How to Make Easy Coil Pots.

History culture hero
16 followers
3 Video Views·Nov 19, 2025
In this video I'm going to show you how to make some easy coil pots. I'm going to show you how
to make three designs. The first one is this cylinder pot, the second one is this one with
the curved walls and then the third one is this one which has got some coil designs.
So if you like the video please do give it a thumbs up and subscribe to the channel
and then you'll be notified when I upload a new video. So when I'm making coil pots what I always
do is I start off by just making a batch of coils and then covering them up with a piece of plastic
and this is how I make coils. So I just start off with the orange shape and then I sort of roll it
between my hands like that, make it into a sort of a cigar shape and squeeze it at the end and then
when you're rolling what you want to do is you want to start with the tips of your fingers and
roll all the way with your hands. I start off just using one hand, roll all the way with your hands.
If you go like that what happens is you'll get ridges in it from your fingers and it'll also go,
it won't stay round, it'll go into a sort of a flat almost pancake shape.
So roll it with your fingers and the palm of your hand right the way through
so it's a full revolution and when it's long enough you can start rolling with both hands
and you might find that it flattens out anyway. I'll try and sort of squish it so if it gets flat
it'll do that sort of thing where it's going, making like a thudding noise.
If that happens what you want to do is just put it on its long,
on its narrow side, flatten it out a little bit so it's more square like that and then you can
make it back into a round shape by just giving it a bit of a twist like that. You twist it
and then start rolling again, it will go round.
When you're rolling you keep your fingers wide and you're sort of moving your hands
outwards like that so it's stretching the clay out. This clay is actually a little bit dry,
I think it's been sitting in its bag for a while and it's been quite hot so the clay
has got a little bit dry so just spray the surface again and then once you've sprayed
it give it a bit of a wipe down so it's not completely soaking wet. If it's really wet
what will happen is the clay will just slide around on top of the surface. If it gets very long
you can just cut it into two pieces because otherwise it gets a bit awkward to roll.
That's about the right thickness, that's that's about the thickness I usually make a coil,
it's about the diameter of a penny I guess is probably one way of describing it. Can you see
that? About the diameter of a penny, maybe, I mean I suppose it's probably about my pinky finger
isn't it? But it's slightly wider than my pinky finger anyway and then when I've rolled it what
I do is I put it on a piece of plastic and then just cover it up and I cover it up because
actually clay coils dry out pretty quickly and you don't want them to be all dry and cracked
by the time you get around to using them. So that's what I'm going to do, I am just going to
roll out a batch of coils. There's a few different ways of making a base, the first one I'm just
going to put this to one side for now but the first technique I'm going to show you is to make
a coil pot, a coil base and do that by making a spiral with one of the coils that you
made earlier on. Cut the end of the coil on a diagonal, I cut it on a diagonal like that
and then when you start coiling it, spiralling it in, you get the little end
and you spiral the little end in like that and it just makes the inner section
of the spiral look a bit more delicate I suppose. So you spiral it in
like that, I chop it off on a diagonal like this so that it's a bit easier to blend it in
and make it into a circular shape. I just coiled that up, I didn't slip and score, I didn't put
any slip in between the edges of the coil there so when you do that you are going to have to blend
at least one side of the coil in and then the blended side can either sit on the outside of
the pot so you've got the spiral on the inside or you can put the spiral on the outside and
have the blended smooth side on the middle, it's really up to you. So when you're making the base
what I tend to do is I'll use a wooden tool, you can just blend it in with your fingers like that
but I actually find it easier usually to blend with a modelling tool and the reason for blending
is partially to make the clay seal up so that it's watertight but it's mainly to make sure that
the pot is strong enough because otherwise when you dry the pot out the coils, if it hasn't been
blended properly and there isn't any slip joining the coils together, the coils will just crack when
they crack apart when they dry or if they don't crack when they dry they'll crack when you fire it.
So like I say if you want the coils to go on the outside you just put the coils base down
and then start building the pot up like that or if you want the coils to go on the inside
and have a smooth outside then that's fine you can do it like that. The other way of making a base,
I'm going to show you a couple of other ways of making a base. One way is to simply press out
a disc of clay. When you're pressing out it's a little bit like making a pinch pot
I guess so just make it into a circle. You really just use your hand to compress the clay down
like that so press it down until it's about the thickness of again of your pinky finger
transfer it onto a wooden bat and you can cut this is a needle tool
okay so you've got a nice disc base that's one way of doing it that's quite a nice
a nice shaped base and the other way of doing it is of course to use a roller
when you're using a roller what you can do is you can put a couple of pieces of dowel
on either side or you can use these now these are just guide rings for the rolling pin
I don't know where I bought these I can't remember whether they're ceramic for them
specifically for ceramics or they might be for baking I don't know but they're quite handy
you just put them on the end of the roller
and then they work like pieces of dowel would do if you put a piece of dowel on either side
it stops you from it means that you roll an even thickness so again just cutting around with the
needle tool so you get your coil pop it around the base so it's sitting directly on the base
and then you cut it this is just a modeling tool but you can use just a knife a craft knife or a
regular knife is fine what I do is I tend to cut it on the diagonal like this I stack it stack them
on top of each other so I know I'm cutting it to the right length pretty much and then I use
just make sure that you can see it cut it diagonally like that and then what I do is I
tend to move that out the way so you've got a little groove there you know you're going to cut
then I pick it up and support it with my hand and then just cut like that
the reason I do that cut it on the diagonal is that if you cut it straight like that
when the clay dries and it does shrink and it's not joined if you cut it on the diagonal basically
there's more of a surface area for the clay to bond together and it's harder it's going to be
harder for it to slide apart if it's on diagonal if it's just cut at a 90 degree angles it can just
pop apart like that this is just a tool with a serrated edge so you're scratching so you're
where the coil is going to sit
and you're just doing that to box so that the the two surfaces of clay have something to key into
score it so that the surface is a bit scuffed up and sticks really well to the base a couple of
directions so you get that little you get those little raised patches little balls of clay coming
up use a bit of slip slip is basically just water and clay mixed together so it's liquid
so ends together coil in place directly over the base and then just gently but firmly
press the coil the slipped surfaces together just blend the two ends together
because you've done slip and score you don't have to actually blend either side you could
just continue adding the coils up in a cylinder as long as they're really well slipped and scored
however i think it's best practice to blend in at least one side but you use a wooden tool you
can either blend the outside if you want to smooth outside or you can blend the inside
and obviously when you're working what you need to do is use your finger your hand your left hand or
depending on whether you're right-handed or left-handed i use my left hand to support
to support the outside of the pot this is the first coil and what i usually do with the first
coil is i do tend to blend the base into the first coil just to make it look a bit neater
you don't have to do this you can leave the base looking like a separate piece of clay
tidy up the base like that
right so then you're ready to add your second coil
and as i say i'm just going to add it directly on top of this one
to make a cylinder so that's where the coil was joined before
and when you put your next coil on it's a very good idea to position the join at a different point
on the pot because if you put it in the same place each time you end up with
um a sort of like a little bit like a fault line on the pot actually where it's a bit weak
and you don't want that so what i'm going to do now is i'm going to take that off
and what i generally do is i will
make it into a ring
and make it into a coil ring
and then attach the ring to the pot i just find it easier to make a neat join
with the two ends when it's not actually sitting directly on the pot
so slip and school two ends press them together nice and firmly without squashing the clay
and then blend it in
i am going to carry on building this and then i'll start the video up again
when i've put a few more layers on and you can see see what it looks like
so then once i finished i would just go around and just tidy up any slip
that's squeezed through or any little bits of clay that are looking a bit rough
so now that we've made a straight cylinder shaped coil pot i'm going to show you how to make a coil
pot where the sides of the pot curve out like that i'll show you a picture of a piece that i made
just recently with curved sides that go up into a narrow neck the way that you do it instead of
positioning the coils directly on top of each other what you do is you if you want to widen
the pot out that way you simply position the coil slightly to the edge on the outside and if you're
bringing the pot in for when you're narrowing the neck you start to position it slightly on the
inside so if you're widening it out you position it something like that just somewhat to the edge
you can't put it right away to the edge if you if you position the coil too far to the side
it's okay for maybe one or two coils but then after a after a little while once the weight of
the clay is quite heavy there's a risk that the pot's just going to collapse if you're
if you're the side of your bowl is going out like that there's a good chance that the clay is just
going to collapse unless you work very slowly and let it harden up a little bit between sessions
and also maybe support the side so the best thing is when you're starting at least anyway
to just position it fractionally out of center so i'll show you what that looks like
so that's what i'm going to do i'm going to build the sides up in a gradual slope upwards and then
once i've reached the shoulder part of the pot which is the widest part of the this is going to
be a vase the widest part of the vase then i'll start bringing it back in again to create a neck
i thought with this demonstration i wouldn't go through the whole making the base base the base
and the first coil because it's the same process making the base and the first coil is the same
regardless of whether it's going to be a straight up cylinder
or other curved curved sides now before i blend the inside i'll just show you what i
mean you can see there there's a bit of sort of hanging over the side
and then again supporting the outside edge with my left hand and with this because there's a bit
more excess clay on the bottom i blend upwards rather than downwards just check that it's okay
and then
so you can see that that is beginning to
gradually slope outwards and i'm just going to carry on building the walls of the pot outwards
till i reach a point the shoulder like i say the shoulder of the pot and then i'm going to bring
it back inwards so what i'm doing now is i am starting to position the coils slightly on the
incline so it's just beginning the curve of the pot going inwards towards the neck of the pot
and then what i do is i just tidy up the outside to get rid of any slip that might have
might be visible on the outside between the coils and get rid of any score marks that are also still
on the clay anyway i won't tidy up the whole thing right now but that is how you make a
curved coil pot with this pot what i'm going to do is i'm going to do some decorative use some
decorative coils you can decorate your pot in whatever way you like you can use barrels or
rolls of clay or balls or wavy coils and with this one what i was thinking of doing is i was thinking
i might put a row of clay balls so i have a coil here just cutting off a small section of that
and then roll it into a small ball and put these let's position these around
maybe about that you know you could if you wanted to you could put a coil across like that so you've
got some open space you can create a sort of a wave shape across the top like that
so you'll see now that what i've done is i have um completed the swirls around the
top and then i've used some just some balls of clay to fill in the gaps between the swirls
i'm just going to show you i didn't want to show you the whole thing because it would be
so long to show you but basically this is what i did once i'd put the swirls on
i made some balls like that fit them in
either finish it off on with a coil on top or you can leave it with the details around the top edge
if you leave it with details around the top edge it's very important that you make sure it's
securely attached that all of the joins around the top edge are blended well just to avoid
the piece cracking when it dries so you do need to go around just make sure that there's nowhere
that the clay is going to be able to crack as it dries and it's a good idea to i mean it's
always a good idea to dry slowly but i think particularly with a piece like this just dry it
slowly under a piece of loose plastic right
anyway that is how you make a coil pot so i really hope you enjoyed this video
and if you did please give it a thumbs up really appreciate that and do like i say
do subscribe to the channel and you'll be notified when i upload further videos
thank you so much for watching
