xTool just sent us their new xTool P3 80W CO2 Laser, and they told us to go big. So we did. We used the xTool P3 to build a massive 8-foot-tall Haunted Halloween Arch and pushed this machine to its limits.
In this video, we show you how to set up and use the xTool P3 pass-through system, cut large sheets of MDF, and assemble a full-scale project with precision. The xTool P3’s 80W CO2 laser power, auto pass-through alignment, and integrated chiller make it the ultimate workhorse for makers who want big results fast.
What you’ll learn: • How to install and use the xTool P3 pass-through system • Cutting full-size MDF sheets accurately and safely • Why the xTool P3 is ideal for large projects and small businesses • How to paint and finish oversized outdoor decor using Foxy Hues Paints • Step-by-step assembly of our giant haunted arch for Halloween events or displays
Materials Used: • Three sheets of 1/4" MDF • 1x2 lumber for framing • Screws, wood glue, and basic tools • Foxy Hues Paints in Twilight Train, Midnight Bandit Mask, and Goose Gourmet Gray
xTool P3 80W CO2 Laser Specs: • 80W CO2 laser with 36x18 inch bed • 24 inch by infinity auto pass-through • Integrated inverter water chiller • Fire detection and suppression system • Modular lens system for cutting, engraving, and marking • Dual cameras for automatic height detection and positioning
The xTool P3 performed flawlessly, cutting through MDF like butter while maintaining precision across multiple passes. This laser truly lives up to its reputation as a professional-grade machine for serious makers.
FYI: We are not professionals, and we don’t claim to be. This is what we found worked for our project. Yours may need a little different approach. We have just enough woodworking skill to make some basic furniture. Safety first!
FTC Disclaimer: This is not a sponsored video. All opinions are genuinely our own. This post may contain affiliate links and we earn a small commission if you make a purchase after clicking on my links. It doesn't cost you any extra. Thank you for your continued support to keep Making It!
X-Tool just sent us the new 80 watt P3 CO2 laser and they asked us to go big.
So how big could I go? Let's find out right now.
What is up? Welcome back. Do you like to make money? So do we. This week we got the new X-Tool
P3 and we're gonna go big. How big? 24 inches by infinity and beyond. This is X-Tool's newest
biggest laser yet and with this new bigger bed comes the new ACS system, the automated creation
system. You literally place your material and go. You don't have to set the focal height and you
don't have to adjust your bed size. The machine will do all of that for you with its intelligent
automation. The auto positioning uses two onboard cameras. It has a 16 megapixel sky view camera
as well as a close-up camera. It will auto focus your material using lidar and it will measure
the precise distance to your material and then it auto lifts the bed to the perfect focal height.
And right now X-Tool is providing a $500 reward if you want to upgrade to the P3. This week we
are making a haunted Halloween arch that's seven feet tall, oh no it's eight feet tall, seven feet
wide and we're doing it all with the X-Tool P3. We're literally thinking outside the box.
Step one. We're gonna gather all of our supplies. We needed three full sheets of quarter inch MDF.
I'm using the good stuff. It's the light stuff. I want to go big with this guy but I don't want
to kill him on his first go so I'm not gonna use any dark stuff. We also needed some one by twos,
a full eight foot. We're gonna need some screws, some glue and of course we'll be using our Foxy
Hughes paints to paint the whole thing. And that is it. Step two. We're gonna make all of our cuts.
We're gonna have to cut down this quarter inch MDF. We ripped it down into these long eight foot
by 24 inch sheets and we're going to use our 80 watt X-Tool P3 to cut these out. But to do that I
think we have to install the pass-through system. Which is so easy to do. So I really wanted to
quickly demo how easy it is to use the pass-through system with this machine. So there's one unit that
you install on the back. It's already installed here and it stays there. You won't have to install
it again. You're going to open up the front door here and once you open this up, X-Tool Studio
knows that you're using the pass-through system. There is a set of rails here that's going to, when
the bed auto raises, it's going to kind of, I guess they're textured a little so it kind of grips it a
little going through. Kind of rides on it. And the pass-through system in the back will clamp it as
you begin your cuts and auto pass-through. You're going to have to install these little rails here
when you use it. Again, this is so simple. I'm just going to slide it in here, slide it down,
twist down these little knobs to keep it in place. So I know I'm doing the full 24 inches so I'm going
to have my rails wide apart here. And then yeah, I'm just going to slide these little knobs here,
clamp it in so they're in securely. And I'm going to do the same thing with two rails on the back
side. Now for this, we could just, this is also magnetized now. So the pass-through system is
already installed in the back. So you're just going to tighten those knobs down and you are
ready to go. Because we're using a full eight foot sheet of MDF, we are going to use our expansion
rails. So this will sit on the front end, the back, just to give you a little more
smooth surface. These wheels roll, they roll really easily. So the board will be supported
at both the front end and the back end. Another great thing about this new conveyor system is that
you don't need a ton of extra material on either end. With the P2 pass-through, you had to have
about 12 inches on either end. Now you really only need four inches at the front, just so that
it has enough room to grab the front of it. And that's it. I really don't need a lot of extra
room or really any extra room for the end cuts. I just need the four inches in the front and it's
good. Now we don't have the AP3 exhaust system for this bad boy. So we're going to open up this door
and we're going to vent it out into the parking lot. And I hope our neighbors don't mind.
We are using the IF2 inline fans to help push this material, the smoke and debris,
out through the hose and kind of get it out and down the sidewalk a little ways. In the right
hand corner, you can see that the P3 recognizes the automated conveyor system is installed.
When I click the measure, it's going to raise the Z-axis and auto set the height of the material.
You can see it's at 0.26. Now I'm going to click the feeder stitching, make sure the sensor cover
is open so it recognizes the length of my material. And then it will start passing the material through
the laser bed, taking images as it goes through and stitching those images together. So you can
see your full design on the material. So if there were already cuts on this material or some other
design on this material, you'll know that you have your design positioned correctly. It will feed it
all the way through until it gets to the end of the material. Push it back to the beginning and
then you can click process. The Hextool P3 is an 80 watt CO2 laser with a 36 inch by 18 inch bed size
and pass through capabilities of 24 inches by infinity. It has an integrated inverter water
chiller, so it maintains stable high power performance over long cutting hours. It also
has a modular design for limitless expansion. You can change the lenses from small, medium to large
and even IR for metal engraving. We're using the medium lens here for cutting our quarter inch MDF.
And as always, Hextool keeps safety as their number one priority. So there's an onboard fire
detection and suppression system with real time monitoring and auto response to fire risks to
deliver top tier safety. The automated creation system is hands free. The P3 uses two onboard
cameras to auto detect the material and adjust the bed height to the proper position. Step three.
Now we paint. We're going to be using our Foxy Hughes paints. These are outdoor indoor paints,
so they do have those outdoor additives that will keep it from fading and it's weather resistant. So
we're going to paint the whole thing with Twilight Train, which is purple, and then we're going to
give it some Midnight Bandit Mask, which is black and some Goose Gourmet Gray, which is a darker
gray. It's a lot of painting. It's a lot of acreage right here in MDF. Luckily we got this big table
makes it so easy. Step four. Time to assemble. We're going to glue all of the MDF to MDF pieces
with this Starbond Thick. It's really just these window frames and some accents on the front of the
front ones, the front pillars. All right, let's get gluing. Let's get gluing.
Now we're going to take these one by twos and run them down the sides and use some wood screws to
screw them in and then we'll attach the back and the front. Then we'll take it outside and hang
the arch. What do you think? Eight foot tall. Hey, we both fit in here easily. I think we put that
P3 through its paces. It did a great. I'm super stoked on it. The 80 watt cut through the MDF like
butter. Yes. 80 watt laser, 18 by 36 inch bed with a 24 inch by infinity pass through.
And look what we were able to create. That P3 did a great job cutting through this MDF. It was super
fast and super efficient. I'm loving the new pass through. I think it did a great job of
setting it up super quickly and pushing the material through quickly. Now they said it was
the ultimate workhorse and I think that P3 might be your ultimate CO2 laser workhorse.
Big thanks to X-Tool for sending us the P3 to test out. We enjoyed it. We have more to come. We have
a lot more to come, but I'm about out of time. I got to go create some more accents and learn how
to make some fire for the top. You got to go make your own archway. And a big thanks to all of our
patrons. We love you guys. That is the best way to support this channel. This file will be up there.
I don't know if I'm going to put it on the website because who's actually going to build this thing,
but I'll give it to the patrons. I can't, I can't balance this thing. Too big. Can't
even balance one side of it. Let it go Garrett. All right. I'll find something.