STEM Stomp Rockets Part 1

Terrific Physics
40 followers
1 Video View·Sep 29, 2025
Hi, I'm Jared. Welcome to Fun Science Demos. Today we are going to talk about how we turn a pile of
recycled plastics into a classroom size version of a stomp rocket. Now there is a lot of science
in these stomp rockets and most of it has to do with forces and motion. The energy from my hand
slamming into the bottle forces the air through the straw and launches the rocket. So how do we
use these recycled plastics to make our own desktop size stomp rocket? Now if we zoom in
and take a closer look at this I think we are going to find it is a very simple build with very
basic materials. My rocket is just a post-it note. My straw is a straw but you are going to notice
here when I take it out it fits perfectly into the nozzle and I did that by adding some tape
to the end of a straw and now I just have a recycled plastic bottle that is going to be my
launcher. So what kind of plastic containers can we use for our desktop stomp rocket? Well we need
something that can hold air but also something that is strong enough to take the force of my
hand slamming into it again and again and again. So these are some of the containers we thought
would work pretty well for our stomp rocket. Juice pouches, little plastic juice bottles,
even some applesauce or yogurt that was stored in pouches that have a nice opening
and seem like they are easy to blow up, put the air back in and they are going to be able to hold up
with the force of my hand pounding into them. So we are going to pick this little pouch and a straw
and the straw is going to be our stem that is going to hold our rocket. You are going to notice
something when I put the straw in the opening it fits but it is pretty loose so the question is how
do I make this straw fit tightly so that I get a nice clean seal so all the air is forced through
the straw and pushing my rocket instead of seeping out where the straw goes into the container. We
decided we were going to try and use tape to make the outside diameter of the straw bigger so it
fits better in that opening. Now you can use any tape, duct tape, we decided we are going to use
masking tape that most people would have in a classroom or their house. We have zoomed in so
you can take a closer look at how we are going to do this. So I am going to go to the end of my straw
get the tape started just very carefully wind the tape around the straw. I did not pick a super
long section because I am not sure how big I have to make it so I am going to test as I go.
Yep, getting there. I need a little more tape.
What is nice about this if I make it too big I can always pull the tape off. Let us give it a try.
Now I am getting a nice snug fit. I think this will work. Now it seems like I have a really
snug fit but I might want to reinforce this with a piece of tape just on the outside.
This is where I might want to use some colored duct tape just for a splash of color.
So let us test this and see if our design for the launch system works. I can smash it,
put air back into it again and again and again and I think we have a working launcher.
Now it is time to make the rocket. Now in another video we are going to talk about
making different types of rockets that we can launch from our desktop, a stomp rocket. But
today we are just going to use post-it notes. You are going to need a stapler and a straw
and maybe a piece of tape. Now we have zoomed in so you can get a better look at how we make
rockets but we are just going to use post-it notes. You can use longer ones or square ones.
For this I am just going to use my square ones. Now the reason we use post-it notes is because
they have a little sticky part and that is going to help our rocket stay together. I am going to
take the same size straw I am using for my launcher and that is going to help me wrap up
my post-it note around the straw. I do not want it to be too tight but at the same time I do not
want it to be too loose. You are going to see the sticky part. I am going to end with the sticky
part so it actually helps hold my rocket together. I slide it off. I am almost there. Now I just need
to run a piece of tape to hold my rocket together and now it is time to make the top part sealed
off. To do that I am just going to pinch the top, fold a little bit over and how do I keep it
so it does not open back up on me? Well I could tape it but in this case I am just going to use
a stapler, put in one staple and my rocket is ready to launch. Now comes the best part in any
stem design challenge, the testing, especially when it comes to rockets. Let us see if my rocket
slides over my straw. It feels like a good fit. Three, two, one. I have a powerful launching system.
Now we have to test it again just to make sure it works. Charge the system, load the rocket.
Now the nice thing about using a bendy straw is now I can change my launch angle.
We are going to try launching right at the camera. Line up my sights. Three, two, one.
So we built our desktop stomp rocket but how do we tell how good it is? Well,
scientists gather data and we need to gather data to see if we can make this better. We need to look
at things like how high the rocket goes, how far the rocket goes, how long the rocket stays in the
air and how much force I apply to my launcher. Real scientists who build rockets look at those
kind of things and we can look at those things too with our desktop stomp rocket. Now we found
that our rocket easily hits the ceiling and if we want to get a better measurement for how far
it goes we are going to have to change our launch angle and that is the nice thing about this bendy
straw. It seems to hold the angle pretty well when I adjust it but you will notice it does not
quite hold it perfectly. To change that, to modify that, we are going to use a paper clip.
All I am going to do is just unbend this paper clip. The paper clip is nice because I can
bend the paper clip and it is going to maintain that angle or shape that I bend it to.
So if I attach this paper clip to my straw I can now change my launch angle and measure
with precision using a protractor. So I have attached my paper clip with tape to my straw but
you will notice something. I really do not have much space left for my rocket to slide onto the
launcher. I think I might have to go back and modify this and make a little extension that
lets my rocket sit nice and securely on the launcher. Now to make our extension I pulled
out a bunch of different straws of different sizes and we are going to test it out. I might
want to use a skinny straw that actually slips down into my launcher or I could use a bigger
straw that slips over top of the launcher. I can try out all these different ones. Now if one is
really too big I might be able to make a slit in the end and that allows me to change that opening
of the straw. Once I find the perfect size now all I need to do is tape my extension to the launcher.
I might be able to trim it and I am ready to go. So we have our extension secured to our launcher.
I can now precisely change the launch angle of my rocket. Now because this straw is bigger in
diameter I had to make a new rocket that custom fits our extension perfectly. Now we are ready
to give this thing a test fly. Here we go. Three, two, one and we have liftoff. There is so much
more we could do with our desktop stomp rocket. We could try using bigger pouches. In another video
we are going to talk about modifying the rocket itself to make bigger rockets, heavier rockets,
lighter rockets, adding fins, adding nose cones and then in a third video we are going to talk
about how we made a stomp rocket for our desktop on a 3D printer. If you want to learn more about
forces in motion or other rocket design challenges and stem builds check out our YouTube channel Fun
Science Demo. Science is so cool especially when you get to launch rockets.
