Compare Model Rocket Recovery Methods | Science Project

Terrific Physics
40 followers
1 Video View·Jun 11, 2026
AI Generated·May contain errors
Video Summary
AI GeneratedThis video demonstrates how to conduct a science project comparing different model rocket recovery methods. Using affordable craft materials, viewers can build simple rockets to test how tumble recovery, streamers, and parachutes affect descent speed and drift, providing a low-cost alternative to using engine-powered rockets.
In this video, I'll show you how to do a science project to compare different recovery methods
for model rockets. While you can do this project with normal model rockets that lift off using an
engine, you don't have to. For a lower cost version, you can simply drop homemade rockets
made from craft materials. In addition to a parachute, we'll also show you how to test a
streamer and simple tumble recovery, although there are other methods you can test we'll
discuss at the end of the video. To make a rocket like the one you see here, you'll just need a
paper towel tube, four three-toilet paper tubes, tape, scissors, string, and some paper. Start by
cutting three or four trapezoidal fins out of the paper. Note that these aren't triangles, they are
trapezoids with a short side here. As I'll show you in a second, we're going to use that to make
them easier to attach to the cardboard tube. Cut a short slit in the edge of each fin, as you see
here, and then fold two tabs in opposite directions. This will make it easier to tape the fin to the
body of the rocket. Tape all your fins evenly spaced around the rocket like this. Next, we're
going to make the nose cone. First, cut a circle out of a piece of paper, then cut a wedge like a
slice of pie or pizza out of the circle. The wedge should be about 90 degrees, but the exact angle
doesn't matter. Once you've cut out the wedge, this makes it easier to fold the circle into a cone.
Use a piece of tape to hold it in place. Now, with a normal model rocket, the nose cone would be
attached to the body of the rocket during flight, and then an ejection charge would eject the nose
cone at apogee, or the peak of the flight, allowing a recovery method like a parachute or streamer to
deploy. However, since you're not going to be launching this rocket, just dropping it, you don't
need to do that or worry about an ejection charge. Just take a piece of string, tape one end inside
the nose cone, and tape the other end inside the front of the rocket. Now, you can either build
more identical rockets, or test multiple recovery techniques with the same rocket one at a time.
The simplest method is just tumble recovery. The rocket loses its aerodynamic shape when
the nose cone pops off, and will just tumble to the ground instead of falling straight down like
a dart. So you don't need to attach anything else to test the tumble recovery method.
Next up is the streamer method. Here, you can simply take a piece of ribbon or crepe paper,
and tape one end of it inside the nose of the rocket. This adds surface area, therefore adds
more drag, slowing the rocket's descent as it falls. It also helps make the rocket more visible,
which is easier when you need to spot and recover a real model rocket.
Finally, you can test a parachute. I have one here, made from a plastic bag, with four pieces
of string tied to four corners of the bag, and then tied together in a knot. I can take that knot,
and tape it inside the nose of the rocket to attach the parachute. Again, with a regular
model rocket, the parachute would be bundled up and tucked inside the body, and then deployed
by the ejection charge. If you're just going to be dropping the rockets, then you don't need to
worry about that. Now, with adult supervision if necessary, you can take your rockets to a
high location, like a deck, second story window, or playground structure, and drop them to compare
the different recovery methods. For a science project, you'll want to choose a variable to
measure, like the horizontal distance the rocket drifts, or the time it takes to fall and hit the
ground. Be sure to conduct multiple trials, especially since wind will be a big factor in
this experiment. When you're done, you can compare your results for different methods.
Check out the rest of our YouTube channel for more rocket science projects,
as well as hundreds of other projects in all areas of science and engineering.
If you prefer written instructions, or you need help picking a science project,
you can also visit our website, www.sciencebuddies.org.
