Building a Countertop For The Off Grid Cabin

The Woodhaven
54 followers
99 Video Views·Sep 14, 2025
In this video, I build the countertop for the off-grid cabin kitchenette.
If you are planning to shop on Amazon, consider my Storefront:
Affiliate Link - https://www.amazon.com/shop/thewoodhaven
Check out Amazon's Hottest Deals (updated hourly):
Affiliate Link - https://amzn.to/3K5ybkn
Check out Deep Discounts on Open Box Tools:
Affiliate Link - https://amzn.to/3MeYZ3h
Music Links: https://artlist.io/Daryl-3392866
DISCLAIMERS*
This video is for entertainment purposes only. It is NOT an instructional video.
This video and/or description contains affiliate links, which means that if you click on one of the product links, we may receive a small commission at no extra cost to you. As an Amazon Associate, I earn from qualifying purchases.
all right so I've got my
panel all uh set up and uh ready to glue
so I've got uh
these and uh they're holding it straight
on the ends and then I've got two in the
center here and I've got those uh
clamped to my bench and that'll help
flatten it out and then I've got uh
these two parallel clamps that I'm using
to uh squeeze them in and uh I've got uh
Dow rods in these just like I did on the
uh
shelf all right this is uh sat all
overnight and half today so let me get
these uh brackets
off they added a couple of these on the
joints keeps them nice and flush
all right I got all the clamps
off that looks pretty good that's
probably the uh flattest one that I've
done yet so uh yeah I think those worked
out pretty
good all right I've got to scrape off
the glue and start sanding
[Music]
dang
it all right guys I just sliced my thumb
open so I guess this is uh this
Project's on hold for a little
bit we'll bring it back later
[Music]
all right so I got this nice and uh
sanded and uh feels pretty nice along
there nice and
smooth got all the glue
up got my thumb
bandaged but uh now I need to cut it to
length I've already put a straight edge
on here and just cut it um cuz the edges
were a little bit Jagged you know where
the boards didn't line up 100% so now
I've got a nice clean cut and I need to
cut it to length needs to be 85 in long
so let me measure that Mark it and get
that cut
okay I need to mark my
offset cuz the blade is
offset pretty close to an inch it's not
exactly an inch
that looks good right
[Music]
there all right now what I want to do is
put this kind of a border around the
edges so that
it'll give it the appearance of
being 2 by material versus one
by okay it's actually going to go
underneath like
this so it'll it'll be like
that and that'll be all the way
around uh at least on three edges it'll
be on the front and the two sides it
won't be on the back
back's going to be up against the wall
you're not going to see that and I don't
have
enough width to do it all the way around
and fit around the
frame all right I've got my pieces cut I
flipped
the countertop over and I've got those
in place so uh now what I need to do is
glue and uh pin nail those to the
underside of the countertop
and uh again I'm just pin nailing them
so that uh they don't
slip and then I'll clamp them and we'll
let the glue dry and then we'll
uh round the corners
off make that a round Corner we'll do
that on both of the front corners and
then we'll uh get it all sanded up
stained and uh ready to take it and get
it installed for
for
C
[Music]
[Music]
w
[Music]
[Music]
all right there's the raw finished
item so you can
see that it has the appearance of being
two byy
material even though it's only one
byy so I just need to uh clean it up a
little bit more with the sander
and uh get it all cleaned off and ready
to
stain so I'm going to let this dry and
I'll come back and I'll give it another
light coat and then uh we'll let it dry
again overnight then we'll come back
tomorrow and uh put some finish on it so
this stuff I don't know if you've looked
at this type of uh polyurethane before
but it's it's milky looking it looks
like milk so when it it goes on kind of
white and then it dries so I started
over here and this is already drying um
clear and it's a semi gloss finish so
it's not going to be really
a really high gloss finish but uh takes
2 hours for this to cure so I'll come
back in 2 hours and give it a second
coat and uh I'll probably end up giving
this uh at least three coats cuz I want
it to have a nice thick uh finish to it
all right I've got some 150 grit and I'm
just going to GL over really lightly
[Music]
all right going to get a just a damp
cloth wipe it down let it dry off and
then I'm going to give it another coat
[Music]
[Music]
all right so you can see how milky this
looks inside the
can and it goes on a little bit milky
but
uh it does dry to a nice clear
finish so I'm going to
uh give this another coat and then uh
we'll bring you guys
back all right I've got two complete
coats
on and uh you can see where I started
it's already starting to look clear and
dry and uh this side here is still a
little bit
milky but uh I'm going to let
that fully cure for another few hours
I'll come back and give it another code
I'm going to do that off camera
though uh you guys have probably seen
enough
varnishing it's not the most exciting
thing but uh yeah this is looking pretty
good I like it you know it's
rustic but uh I think it's going to do
the job and uh you can see I got a
couple runs here where I was uh sealing
the backside as well even though that's
going to be up against the wall I want
to seal it anyway but I think this came
out pretty nice um it's nice and flat I
think that uh those unri calls worked
out well for uh keeping it relatively
straight and uh I really like that
General Finishes stain this is Antique
Walnut
that I've got on it and then I've got
water-based polyurethane as my top coat
and uh you if you're going to be putting
this on anything where you might be
preparing food waterbased is actually
better than oilbased because it doesn't
have any voc's in it so it's
non-toxic so I think that's going to
wrap up this week's video so we'll leave
it here
and uh I'll talk to you guys later
