Foldaway Desk for the Off Grid Cabin

The Woodhaven
54 followers
85 Video Views·Sep 14, 2025
In this video, I build a new foldaway desk for the off-grid cabin.
If you are planning to shop on Amazon, consider my Storefront:
Affiliate Link - https://www.amazon.com/shop/thewoodhaven
Check out Amazon's Hottest Deals (updated hourly):
Affiliate Link - https://amzn.to/3K5ybkn
Check out Deep Discounts on Open Box Tools:
Affiliate Link - https://amzn.to/3MeYZ3h
Music Links: https://artlist.io/Daryl-3392866
DISCLAIMERS*
This video is for entertainment purposes only. It is NOT an instructional video.
This video and/or description contains affiliate links, which means that if you click on one of the product links, we may receive a small commission at no extra cost to you. As an Amazon Associate, I earn from qualifying purchases.
[Music]
[Music]
all right so you can see here that this
is the desk from my cabin I've uh
removed it and uh brought it back to my
Garage in
Utah and uh the problem is where I had
this installed it's too large for the uh
storage couch that I built so I pulled
it down I was going to move it against
the back wall but uh it's also too large
for that space as well so what I'm going
to do is I'm going to rebuild the desk
going to change it up a little bit make
it a little bit smaller and uh make it
one that mounts bounce on the wall and
folds up so uh
that's what I'm going to be working on
today so let's get to it all right so
let me get this laid out and uh give you
an idea of what it's going to look
like so my previous
desk had storage
underneath this is actually going to be
a desk that sits like this so the
storage will be against the wall and
then I'll close the desk up against it
so it achieves the same thing gives me
some storage but it folds
away and uh I know Frank I know you said
I should have done this to begin with
should have listen to you
all right so it's going to be something
like
that and the thought is is that I'll
have on the left side I'll have two
equal
shelves on the right side I'm going to
offset that so I've got a bigger area
here so it's a place where I can store
my laptop and then I can put some
smaller things up
here so uh let me go ahead and start
putting this together all right so this
is the biggest problem with buying
lumber from you know a big box store so
if I put these together here they're
pretty flush looks nice but over
here you can see that you know I've got
like a 16th of an inch this one's a 16th
of an inch higher than this one and
that's where mistakes get made when you
put stuff like this together and you
know it's no fault of the guy doing the
DIY project it's just you know the
lumber is not
consistent so what I want to do to
alleviate that is I'm going to take all
of the
outside board
so you know these four right
here and I'm going to run these through
my uh table saw so that I can get them
exactly the same size and these internal
ones I'm going to take about an inch off
so that they actually are are ins set
inside uh the storage area so these
three boards I'm going to do the same
thing to but I'm going to instead of
taking a 16th off I'm going to take an
inch
off all right I've got it all set up
I've just run the first board through so
let me get the other three done
[Applause]
[Music]
[Applause]
[Music]
[Applause]
all right I've now got all four
boards with the same w
[Applause]
[Music]
[Applause]
all right I ended up just taking a/ inch
off so I'm going to put that together
over there and we'll see how it
looks all right I like that
it's down uh half an inch all the way
around I think I'm going to go with that
so let me get these put together all
right get some glue going
all right I've got the outside box all
glued up should be able to take this
apart I decided to just single these up
instead of doubling them up that way I
was able to get
three corners and then I used my uh my
Square for the fourth
now I need to get my inside built and
then we'll get that uh in here but
before I do that I want to Route all the
uh outside edges I'm not going to Route
the back side that's going up against
the wall I want to Route the front and I
want to build the internal piece and
then route it before I install it
because once it's installed uh these two
because they're not on the same level
I'm not going to be able to
route you know up against the edges so
let me do that
[Music]
[Music]
there's my outside uh walls so let me
build the
interior and uh we'll route that out and
then we'll install it inside here
for
what
[Music]
[Music]
all right let's see if this fits
all
right it's a pretty good
fit now I just need to attach
this then I can work on the foldout
piece all right there we have it check
it for
[Music]
square that's dead on
looks pretty
good all right so what I did was I cut
the uh the top out of the original
desk and I uh
cut it to size so that I could use it
again for this desk and the cut offs for
these shelves right here that's what
these are and these are just sitting in
here pressure they're not really
attached yet so I've got one in each
place and that's just to keep stuff from
sliding out I've got my two hinges that
will attach the desk
board to the uh H the cabinet I guess
and then I've got this piece left over
and what I want to do is rip it in half
and create two nailers that will go
along the back
here and that's what I'll use to attach
the desk to the
wall so that's where I am I guess I need
to uh get those nailers cut to size and
installed and then I'll probably stain
all of the uh components individually uh
these just snap out because I don't have
them installed yet I just wanted to see
how that was going to
look so uh let me get to
that all right I got that board
split and those are just pressured in
there they're not really attached yet so
what I'll
do I I don't know if I should attach
those before I
stain no I think I'm going to take them
out stain them and uh I think I've got
everything ready so I'm just going to
stain everything and then I'll put
everything together
[Music]
[Applause]
h
[Music]
[Music]
[Applause]
[Music]
[Music]
for
is
[Music]
all right completely done I got these in
glued and pin
nailed got my uh backer boards there
that are also
glued and pin
nailed and I threw a couple of screws
in just for safekeeping
and put a couple up on top as
well because this is going to be holding
all of the weight of the
desk so I wanted that to be uh little
little bit extra so I've got glue pin
nails and
screws I think that's going to work out
a lot
better uh for you know fold down desk
doesn't take up as much room still have
storage you know on the different
shelves upper shelves I've even got a
little guard bar and then on this one
here where I'm going to probably put my
laptop I'll have that guard bar there to
uh keep it from
sliding but uh I think that's going to
do it for this
video so I'll talk to you guys later
