🔧 Repairing Cracked Lapstrake Planks with Epoxy | Traditional Wooden Boat Repair In this episode of Nomad Boatbuilding, Mark Reuten tackles cracks in a traditionally-built Acorn dinghy using time-tested techniques paired with West System epoxy. This classic wooden boat, once built at the Cowichan Bay Maritime Centre, suffered sun damage during dry storage—leading to several split and cracked lapstrake planks.
Mark walks through a careful repair using Dutchmen (splines), epoxy filling, and heat-assisted saturation for tight hairline cracks. With a blend of traditional craftsmanship and modern epoxy methods, this is an excellent deep dive into wooden boat repair for anyone restoring or maintaining traditional planked hulls.
▶️ In this video, you’ll learn:
When and how to use splines to reinforce cracked planks
How to flood-checks with unthickened epoxy
Tips for using heat to thin epoxy without weakening it
How to stop cracks from spreading
When to choose spline vs. fill-and-seal techniques
Smart clamping and jigging techniques for awkward repairs
Why grain orientation and end-grain saturation matter
This video is the first of a two-part series focused on bringing this traditional dinghy back to life. Stay tuned for Part 2!
Chapters: 00:00 Intro 02:06 Roll the hull and plan the repair 06:46 Making the router template 08:36 Using the router template 10:00 Double sided tape tip 13:44 Cutting the dutchman slot 14:21 Inspect the progress 18:18 Make and fit the dutchman 20:07 Marking the length with a masking tape trick 23:59 Gluing the Dutchman 35:10 Fairing the dutchman 39:35 Outro
Howdy folks. I'm Mark Ruden. Welcome
back to Nomad Boat Building. We got an
interesting project on our hands here.
This is an Acorn dingy built at the
Couch and Bay Maritime Center. This is
one of the boats that is the result of
their traditional lap strike boat
building course. Now, this is the same
course that I teach there. I've built a
couple of these so far with the center.
I did not build this one, though. This
one would have been built under the
guidance of Eric Sanderlands. This boat
was actually into the shop a couple
years ago. At that time, I prepared a
bunch of the planks. We gave the
interior a fresh coat of paint and the
customer took care of the rest of it.
And maybe you'll remember this dinghy
from my video on how to strike a water
line. This is the boat that we did that
on. Anyhow, I got a call from the
customer. This boat has been sitting in
storage out in her yard for the last
little while and she discovered there's
some cracked planks as a result of that
storage that we need to deal with. I
think the primary reason for this is
that this is basically stored in the
direct sun and uh previously this boat
had been living in the water for the
bulk of its life. So these are not good
combinations. At the very least, if
you're going to pull a traditional boat
out of the water and store it out of the
water for a while, you want to start in
a cool place that is not too bone dry.
Uh preferably with a lot of ventilation
around it. You don't want to put a
plastic bag over it, like a tarp or
anything like that. um at least not
tightly. You know, if you got to drape
one over loosely, that's okay. But this
was stored essentially where direct sun
can pound down onto it. And we'll see
the results of that when I flip this
over. Now, this boat represents two
unique repair challenges. So, we're
going to tackle this in two separate
videos. Let's start with the simpler
one, which is fitting some splines or
Dutchman over the cracks on the port
side. Before we do that, you got to
check this out. Is that not a beauty?
I'm hoping this is no longer a viable
wasp nest.
So weird.
I was looking for better ways to roll
these things.
So I haven't quite determined exactly
how I'm going to fix this yet. There are
some methods that I am inclined to use
that would be sort of my default, but
you know, every boat's a little
different. Every every
repair demands a slightly different
approach.
This one's got some challenges for sure.
And so those challenges is what makes me
unsure as to exactly what my approach is
going to be.
It's going to be one of those rules.
It's a bit of a gong show. I can tell.
Little bit of a gong show.
Worries always about your straps
slipping off the end.
So, we got this crack running all the
way through here.
Another small one there.
One there, one there, one there.
These are all fairly concentrated. If I
push down on them, you can see the plank
closing up. So, is that another one
there? Looks like there's another one up
there, maybe.
The way I usually deal with checks like
this is by putting a spline in them. So,
routing a slot that doesn't go all the
way through the planking, but say, you
know, half to 3/4 of the way. And that
just helps to maintain the orientation
of the planking because I don't want to
punch a hole all the way through. And
because I can't clean up on the inside,
if I put a spline all the way through,
I've got all the ribs in the way.
There's no way I can clean those up like
clean down the inside. So, I go I leave
the inside intact and then you you still
see a bit of a crack, but at least it's
it's filled, right? I think that's what
we're going to have to do on this side.
But because there's multiple cracks, I
think I might go with like a wide one.
Normally, I would just make them as thin
as possible, like a quarter inch.
But given all these different ones here,
I think
probably like a full inch wide.
Yeah, one inch wide. That gives me like
a little quarter inch overlap or so.
I think that would be good. So, we can
do that all the way down here. So, I
think we'll make plywood template.
There's like a hairline crack here. I'm
really Oh, man.
I'm reluctant to try and
put a spline on those because they're
they're right right up against the keel.
So, it's really hard for me to do
anything about those. I almost never do
this um because I I'm always unsure
whether or not it's the best idea. But I
think what I'll do for these guys is
just take my saw and open them up a tiny
bit. And I think we'll just
sweat some epoxy down into those. Get
the heat gun on them. Try and really
just bring those together cuz they're
cuz they're dead tight. The reason I
don't typically do that is when there
when the cracks are open like this, I'm
afraid of putting in a hard epoxy,
like a big glob of epoxy that
potentially then could cause when the PL
planks swell could potentially cause
like a crack happening elsewhere. Um, I
maybe I'm alone on this. Maybe other
people were just like, "Oh, I need to
just fill with epoxy and call it good."
But I've always gone with the the
Dutchman spline idea and I haven't had
that ever kind of fail on me. So I'm I'm
inclined to stick with that. And that
way I can control the the orientation of
the grain and the of the spline, too.
I'll usually make it vertical grain. So
it so it can't it's not going to swell
laterally. It's only going to swell
vertically and there's no that won't put
any pressure on the planks.
All right. And I've cut a couple of
strips to be the uh main body of my
template. Now I'm going to make some
ends to fill in the ends. I'm going to
put a scarf on them so that I have
proper kind of scarf taper at the ends
of these splines.
[Music]
[Music]
So, it occurred to me I'd like to make
these tail ends, these splines a little
shorter.
So,
all I'm basically doing is making a
bird's mouth scarf or a bird's mouth
tail on it by
having the ang or having the length of
of it by making it like a bird's mouth.
I'm not sure if that makes any sense.
It'll be clear in a moment. I'm
essentially creating this template in
two halves. And then I'll connect the
two halves together to give us our
finished shape.
So, what we do is we take this
and we'll secure it in position here.
Probably put it down with um
maybe some double-sided tape and then
we'll use that to cut our slots at the
rotor. So, this way I can juggle this
until it looks looks just right. Just
have to make sure that all the things
that I want to address land within the
void.
And I've often used my 28 gauge pin
nailer to hold these on, too, because it
leaves such a small hole, you can almost
ignore it. You just put a drop of CA
glue or something in the hole to fill it
back up.
I've got my router set up with this
little patterning bit. It's just got
like a the bit itself is maybe only
quarter of an inch long. It's intended
for like doing hinges. So, it's just for
shallow mortises and it's exactly
perfect for what we want with my
pattern. I'll do it in like two passes.
First pass is going to give me eat about
an eighth of an inch of depth. And this
planking is
usually on the thin side is the way it
these boats were getting built. Like
5/16 or so. So, I'm going to be careful
not to go all the way through. So, we're
going to leave a little bit on the
inside.
And that's just so that the the spline
that we put in has got something to
bottom out on. So here's our pattern.
I've marked out normally where it's
going to go.
So I'm going to start with some
double-sided tape. So here's a little
simple trick with double-sided tape.
If you cut it into little
parallelograms,
it's about a million times easier to
peel the backing away.
Backing
when you do it in just cut it straight
across the tape. Uh, for some reason,
it's just I don't know, the paper just
doesn't want to peel back easily. And I
found when you just have the skewed
angle, it it's just easier to tease the
corner off and and peel back the tape.
So that's what I'm doing. I'm going to
put a few pieces on here along the way.
And I think I'm probably going to use
just a few pin nails as well because I'd
hate to have the pattern suddenly decide
to shift while I'm cutting. So
probably just a couple of them at one at
either end maybe to just be 100% sure
the pattern doesn't go anywhere. And
when I did the splines on the outside of
this, I didn't bother with
making a pattern like this. I just used
a batton and use the edge of the router
running along that bat. And so that's
when I'm just doing a quarter inch deep
spline or quarterinch wide spline,
that's kind of easier to do. Or if I'm
doing any spline that's just the same
width as the better bit, I'll do it that
way. Uh, but because this
spline is going to be considerably wider
than the router bit,
I opted for making the pattern. It's
amazing. It's amazing how much easier it
is.
Those of you who know know,
but I wish I had,
and I don't have any on hand, um, is
double-sided masking tape.
I think I can get it from Uline. I just
believe it was kind of like one of those
things where you had to buy several
rolls to get it. And I
cheap skate stopped me from doing it.
Okay.
We want to make sure we're several
inches beyond our split just to make
sure we got getting a good result.
And I'm juggling this around so that I
cover all the splits here.
Don't worry too much about necessarily
being in line with the grain of the
planking because I can't see it
underneath. But yeah, see the twist here
is such that I think I'm going to have
to pin this down in order to get it to
stay put.
And what I should be doing is just is
checking that it's actually an inch wide
in the middle and not spllaying out.
Yeah, that's good. Perfect. Yeah. Now,
this tape is not going to hang on on its
own. I'm going to have to pin it.
These pins are only going into the
planking. Maybe about an eighth of an
inch.
I need one here.
[Music]
If you're liking these videos, you can
support me by giving me a thumbs up,
throwing me a couple of bucks with super
thanks, subscribing to the channel,
turning on notifications, and of course,
you can join me over on Patreon. Find
links in the corner or down in the
description.
[Music]
All right, tease this off.
That looks pretty good.
I was able to get deeper at this end
than at this end just because of the the
wind I guess was not letting the pattern
sit down quite as low as it could. It's
still got enough coverage that we'll be
able to patch this up well enough. So,
I'm not going to worry about that.
There's this other fine crack here. I
don't know.
I don't know that I can even get in
there
effectively.
It's the uh the downside of this
technique is you're limited to where the
router can reach.
Yeah, even
even if I wanted to, I can't get the
router into that spot. Uh it's a pretty
tight crack.
[Music]
It's really hard to gauge what's even
there.
Okay. Well, given how tight this one is,
and given the limited financial
resources on this job, I think we'll
just go with flooding this one with
unthickened epoxy.
Get the heat gun in there. And what
we'll do is we'll drill. Could do that
right now. Actually,
zoom in on this crack.
What we do is we put a little we just
drill a small hole right at the end of
the crack. That'll stop it from going
any further.
Now, we'll fill that hole, too. But
this is a thing.
I can't even tell if there's even a
crack here. It looks like this is
already filled with something.
Maybe it's just paint and stuff like
that. I'm not going to try and reef it
out cuz it doesn't look
very reefable. But I am going to try and
flood some unthickened epoxy into these
areas. But this little hole I drilled,
we'll just put a tiny little cedar
plug in there. Just a drop of glue.
Just popped it in real gentle.
And that's all there is to that.
So now I'm going to find some material
to make the spline that goes in here.
And we'll just pop that in.
[Music]
Swipe some of sandpaper.
Although it hardly needs to sand cedar.
It's so
absorbent that it will just gobble up
epoxy.
tail end of these guys. I'm gonna leave
them round because I think that's going
to make for a better result than if I
tried to make them pointy.
So, we'll just leave those the way they
are.
Let's go find some spline material.
Okay, I found some cedar here that looks
like it's same roughly the same quality
as what's there. It was a bit darker.
That doesn't matter. Grain orientation
is the same.
grain density is the same. So, it'll be
a good a good fit.
[Music]
[Music]
What?
Okay, that's ready to go in.
Just got to
fits nice there. It's a little just a
tiniest bit snug here and I want that
cuz this has got some twist and so it's
going to give me a little bit of
friction to help hold it in once I've
slobbered it up with a bunch of epoxy.
Remember that little tape trick I showed
you for trimming off the end, finding
the the end point. It's a good little
trick.
So, that's a nice tight fit. And this
guy,
like other than seeing that there seems
to be a crack, but it's just like it's
totally filled with stuff. So, we'll
just flood that with unthickened epoxy
and warm it up with a heat gun. And
whatever's in there will be the filler.
Little check here. We'll squeeze some
stuff into that. Nothing much I can do
about that one there. I don't want to go
digging.
And then so that'll be that plank, I
think.
And then we got to uh come up with a
game plan for this side. I'm still still
waffling on what that is. So, we've got
our Dutchman, our spline that we're
going to put in here.
I've got that hole cleaned out.
Everything is nice and clean. sanded off
the bottom edges of this ever so
slightly just so they don't get hung up
going into the hole.
So, we'll just put that to the side.
And actually, we can put this in place.
It's always good to do sort of a a dry
run. So, this end kind of fits in there
fairly snug.
This end springs up a little bit.
So, what I want to do is I think to
clamp this in place, rather than putting
nails in or anything, I just want to
shore it down from the ceiling. So,
let's measure for some shores.
Just try and square off the face of that
somewhere. Might have to screw a little
block to the rafters here to hold it.
And that's going to work well.
Good bit of scrap.
Okay, there's one of our shores. And now
down here, I'll do the same thing.
You notice my ceilings are covered in
all manner of
stuff. I'm doing exactly this sort of
thing.
There we go. That'll work. Something
like that.
Cut this other stick down to that
length.
[Laughter]
[Laughter]
Go with the west system.
105 205. We'll go for the faster cure on
this.
Also bit of junk on the end of this guy
that
got to beat off.
Just clean. All right. Always mix your
epoxy a full 2 minutes if you're mixing
by hand. With this mixing wand, I
usually go a good solid 30 seconds
depending on the volume.
Going to start by just wetting out our
hole. I almost always use two-stage
bonding in which we first wet out our
parts but with unthickened epoxy before
using thickened. Now, there are some
cracks
running right through the planking here.
Um, so we are going to thicken up some
epoxy for the final installation.
thicken it up a little bit because I
don't want it running right out of those
cracks.
But for the moment, I just want
everything to saturate really nicely.
Okay. Then we have this little maybe
crack. I'm just going to try flooding
this with a little bit of epoxy. We're
going to hit it with the heat gun.
>> For structural applications of epoxy,
you only want to thin it using heat. If
you use solvents, it weakens the bond.
And that's all we're going to do
because honestly, I can't even tell if
there's a real crack there or if it's
already been filled.
Maybe I filled it before. I can't
remember.
So, with that taken up, I think I'll wet
this out, too.
Especially that end grain
the very end.
really want to make sure that we've got
that that takes up
as much unthickened epoxy as possible.
So, endrain is always the problem with
all gluing. There's very few glues that
will glue end grain very well
except epoxy. Now, there was a guy that
a little while back played around with
end gluing.
Uh he did an experiment just in gluing
with regular carpenters glue and he had
some surprising success
at that. Um I don't know what to say
about that. The chances you get a good
longl lasting bond in of an inglue joint
like that is is pretty low. So uh while
he his experiment might have been
successful, it is not something I would
rely on by a long shot.
This is one of the reasons that miter
joints don't glue very well. That why
they're prone to breaking apart is
because you get a lot of wood movement
across a miter and that um can break the
joint fairly easily and it is basically
an end endrain joint. It's a one one
joint I guess one to one miter. So
that's like it's it's so close to a butt
joint it's it's kind of ridiculous. Um
whereas a scarf joint we'd shoot for a
much longer ratio of you know 6 8 10 12
20 to one depending on the application.
While a short 45°ree
joint might be perfectly acceptable in
the world of furniture making and um
house carpentry. It is not considered to
be very useful in the world of boat
building. And um there aren't that many
occasions where even you find a a miter
joint in boat building actually. It's
it's quite rare.
Okay, so that's looking good.
Make sure there's no junk in that hole.
Okay, I think I'm going to add a little
thickener to this. Then
we're just going to use the standard
406 colloidal silica
anti-sag as it's sometimes referred to.
Don't need very much because we already
used some of this epoxy. I can feel my
pot already warming up because it's a
pretty hot day.
So, I just want a sort of a wet
a wet mix here.
too dry and it might fight me to
actually fit it into the fit the the
Dutchman into the hole.
Okay, it's mostly because there's just a
couple little spots around the edge
at the ends here where the joint isn't
100% tight.
And so you definitely want to make sure
those fill.
So, as you can see, I'm really just kind
of painting it on just like I did the
last batch. which I'm not worried about
massive amount of volume because I don't
think I need it. I do however want to
make sure that I get some down into
these couple of cracks that are a little
more open than the others.
Like this to be mostly wood in the
joint, not mostly glue in the joint, if
that makes any sense.
Okay, so that looks pretty good.
And I'm just going to put a little
dribble out.
Now, let's see. Where's my knife? Just
want to check my end here.
Hit this with the heat gun a little.
You don't want to hit it so hard that it
starts to kick off. You just want it to
start liquefying on you.
Yeah, I don't see it wicking down into a
joint, which suggests to me that there
isn't really a hole there. Just sort of
sitting on the surface.
If there were like an active crack, I
would I would I I would expect to see it
sort of falling into that crack,
especially since it's been sitting there
for a few moments. Just going to throw a
little squeeze out onto this other crack
up here.
Still have to tr that in, but just going
to get it while it's sitting in the pot
here.
Okay, let's throw our Dutchman in
the tight end.
And if you're doing this, of course, you
want to make sure you mark the Dutchman
itself so that you know which end is
which because it's easy to forget and it
may or may only fit one way.
Stop to clean up my fingers a little
bit. Epoxy will easily clean up with
acetone or lacquer thinner, but I much
prefer to use alcohol, either denatured
or methylhydrate,
but you can also use white vinegar. It
works really well, too. Although things
are just a little bit stickier with it.
doesn't kind of cut through the goo
quite as well. Nice.
Okay,
let's push these shores down. Uh,
make sure I don't glue my shore to this.
Now, the other one
kind of relying on the um this thing
having a bit of a spring to it. Looks
like I might have to get another shore
in there somehow.
You'll note the whole thing is a little
bit proud, too, because the idea is that
we'll plane this down flush after it's
all set.
I should probably get another couple
showers happening in the middle because
it's kind of winding, wanting to wind
out a little bit.
In the uh instrument world, these are
referred to as go bars.
People will have what's called a goar
deck, which is like a
essentially a box with a top and a
bottom and no sides that you stick a
guitar top into. when you use it for
gluing braces in and things.
Problem is this got a flexible surface
here and so
things you push one spot down and
another spot loosens up.
Okay.
There we go.
That was the ticket. Just do a quick
clean up here.
I don't want to do too clean a clean up
on this particular
job because the potential for this cedar
to start kind of um sucking the joint
dry because it's such absorbent stuff.
So you want to leave just a little bit
of squeeze out here and there just to
get wicked back in
just in case.
So it's just pulling off like heavy
globs that will make it difficult to do
the uh tidy up later on
and leaving the rest.
Okay. Yeah. And this this whole bit that
I
coated before looks like it's not
pulling in anything.
So, we'll just clean that up. I'm going
to leave just a little on the surface,
though, just in case.
Just sand that back a little bit
afterwards or scrape it back.
Then the last bit is our little crack.
It's a little bit heavier here.
It's looking a little sloppy. So, let's
clean that up. This looks a little
unfinished, but I'll come back and do
another fill later on when I'm doing
another glue up.
All right, that's it. We will leave that
overnight. Let's get a quick peek
inside. Make sure we don't have anything
dripping out. Yeah. So, I got to come in
here, clean that up. Yeah, you can see
that
epoxy weeping through that fracture.
That's dirty. I wish I'd cleaned that
before I did the glue up. Oh well.
Normally, I would have cleaned this
whole thing out a few days before
starting the repair, so it has time to
dry and stuff, but this repair is on a
budget, and that budget precludes me
from taking the time to clean it because
it does take some time. You'll spend an
hour or more cleaning the thing out
properly. Okay, I think that's all I can
do.
All right, we can lose all of these.
So that looks pretty good.
[Music]
[Music]
[Music]
Heat.
Heat.
[Music]
[Music]
Hey,
[Music]
heat.
[Music]
Looks like I got just a little bit of a
spot where it drooled the epoxy in and
left my joint a bit dry, which is odd.
You saw how heavily I mopped all that
down with epoxy, but that's okay. We'll
just come back and we'll wick a little
more in there. Hit it with the heat gun
a bit, get it to soak in, and we'll fill
that right back up. Well, our repair is
done. And after a lick of paint, our
Dutchmen is completely invisible, which
is exactly what we want. So, I'm really
happy about that. Using Dutchman to
repair wooden boats is a timehonored
tradition. Anytime you have a problem
that needs addressing, a Dutchman can
often help to fix that. Of course, you
do need to make sure that Dutchman is
structural, and if you're dealing with
rot, you need to make sure that you're
going far enough past the ends of the
rot in order to make that a reliable
repair. That's a subject for another
video. If you have a hairline crack and
it's absolutely tight, I'm sure you
could get away with just flooding
unthickened epoxy into it and have it be
just fine. I think drilling little holes
at the ends and plugging those is a good
methodology for stopping the crack from
running further because even if you can
flood the bulk of that crack with epoxy,
you may not get the ends and who knows,
it might keep on running. So, that's
definitely worth doing. If this boat
returns to the water and swells up a
little bit, I'm not too worried about
that. Dutchman causing any problems
because the the wood we've used in the
Dutchman is vertical grain. It actually
matches that of the plank. So, it should
come and go along with the rest of the
plank reasonably well. I think the bulk
of the movement that's happening in this
boat that has caused this plank cracking
is in fact not the planking itself, but
the keen that this is all fastened to.
Oak does move quite a bit with the
changes in moisture. And um my guess is
that that oak keson might have come and
gone enough that it fractured the plank
and fractured the uh the fastenings on
the other side in particular and on this
side causing the fractures in the plank
itself. Now the repair on the other side
is considerably more extensive. So we're
going to cover that in a separate video.
Now if you like this repair video, you'd
like to see some more of them, please
leave a comment. If you'd like to
support these videos, please join me
over on Patreon. You can find links in
the corner down in the description. So,
I want to thank you all for watching. I
especially want to thank West System,
the sponsors of this video. West System
make great products and if you have any
issue with them, they have got a great
tech team that will help you
troubleshoot those issues. So, I hope
you'll join me again for the next West
System video. We'll see you later,
folks.