all right guys I'm going to start this
project again on the side so let's go to
the blue green plane again arpha
rectangle and we're going to go up
41.25 comma with a depth of 8.25 in for
our side pieces P for push pull this
direction 75 in Enter space bar triple
click G component
enter and oh my my bad I forgot to add
the go back into the part and add this
little rabbit along the back side so
this rabbit is going to be 375 it's
going to be 38 of an inch wide comma .25
for the
depth and that will allow me to have a
38 of an inch rabbit to accept a/ qu in
panel that's going to go all the way to
the bottom all right now that part is
complete M for move I'm going to press
control to copy another piece side by
side and my rabbits need to be opposite
so right click flip along the red now
they are opposite I need to move for a
spacing of 22 in in
between and that's the total width of
the book case r for rectangle along the
bottom here and P for Push Pull I'm
going to say a thickness of 75 in space
bar triple click chaper component enter
this is the top and bottom fixed shelves
so M for move control brings up plus
sign and I'm going to copy another one
up here this bottom one is going to be 3
inches off the bottom and this top one's
going to be flush with the top of the
sides and I'm going to secure this with
pocket hole screws 1 2 3 one two three
and overlay this with another piece so
you'll never see the pocket holes and
I'm also going to put pocket holes this
direction so it'll tie into the face
frame and same width down here except
pocket holes will be on the bottom so
this it's going to secure to the face
frame right here and the side of the
face frame is just going to be glued on
so it'll work out um let's go to the
Bottom t for tape measure off the bottom
3 in M for move from right here to right
there let's delete that and now let's
work on the face frame
so the width of the face frame is going
to be 1.5 comma. 75 in for a thickness P
bush pull
all the way to the top space bar triple
click GF component enter M for move
control brings up copy I'm going copy
another one right here so now I can go
on this plane and draw the top piece
which is going to be 3 comma. 75 in F
push pull from here to here space bar
triple click TF component enter now I
can just move this one copy
it all the way on the blue plane down to
here
all right so there is my carcass of the
bookcase and now let's see I can just
let's work on the bottom right now let's
add this bottom
trim t for tape measure off the bottom 3
in and that is lined up with my bottom
shelf and I'm going to go to the back to
draw these and you'll see why in just a
second I'm going to draw the profile of
the trim piece so Alpha line let go this
direction .125 in
let's go down .125
in now this may get a little confusing
but just hold on one second let's go
this way I've already gone 0.125 and I
need to go a 3/4 inch thickness so I
need to go
625
and
625 and 625 so basically I was just
trying to locate this point right here
for my CA Circle
to
go like so now I can delete this I'm
going to make a little round over
profile
here and delete that alha
line and along the blue axis I want to
stop at the base right
here and just connect the dots so
there's my profile of a 3-in tall piece
with a simple round over and I want to
make this this uh profile molding go
along the side the front and along this
side over here I don't want it in the
back so this is a really handy tool
called the follow me tool L for line
let's make a path we've already got the
profile we need to make a
path now let's select that path control
brings up the multiple
selections and here's my
path follow me follow that path what do
I want to follow that path I want this
to follow that path and there you go now
youve got your nice little molding all
the way around and it's a lot easier
than drawing one copying it over here
and flipping it then drawing this other
one then connecting all the miters and
all that good stuff uh follow me command
works really well for molding that
you're trying to trim something out and
you know you don't need all these pieces
uh individual pieces because you're not
going to Dimension them individually
you're not going to see them
individually in the SketchUp d diagram
so this will work just fine space bar
triple click G component
enter now let's do the pretty much the
same thing on the top except this time
I'm going to change the profile a little
bit so Al for line let's go over 75
in .125 down it's back up here to this
point again let's go 75
in1 25 down or over rather and I'm just
going to reference off of this to locate
my circle see if a circle right here to
right there I can delete my line delete
this and now there's a nice Cove profile
I have real quick for
molding so the same follow me command
Alpha line make a
path for the profile to follow so
there's my path space bar select my path
hold control to multiple select my path
I want follow me follow that path what I
want to follow I want this to follow
space bar triple click G component enter
so now I've got my nice Cove molding all
the way along the
top all right now I want to add my
topmost
piece and for that let's just let's use
the offset command so it's the quickest
way to do this real quick
I just drew a rectangle let's go to
offset click on this rectangle and only
want to overhang of 0.25
in but I don't want any overhang on the
back so I'm just going
to connect these dots and delete this
overhang on the
back I also need to delete my
original lines that I
created and and now I can push pull this
75 in in my direction Enter space bar
trip actually no let's not do that got
ahead of myself again all right now
let's cut out for the top
molding so T tape measure from over here
let's go with 65 enter Alpha line and
I'm going to go
down1 125
enter and see for Circle
just like
so just delete all this extra here and
now I've got this nice little path that
I can cut out so delete this and I've
already got my my uh path
here so select select
select Push
Pull that's the
profile so now I've got this pretty nice
little molding setup right here on
top all right now let's just go ahead
and put the shelves in so R for
rectangle um my width is 22 in according
to the dimensions down there and my
front to back measurement is 8 in
because I removed a/ quar inch for the
back panel so let's go with instead of 8
in let's go with 22 comma 7 .25 that is
the exact width of a 1x8 and it will
also allow me to put a little bit of
face banding on here so P push pole this
direction point 75 in Enter space bar
triple click G component enter and I'm
just going to move it along the blue
plane just off of the base it doesn't
really matter where right
now and now I'm going to put this little
piece of face banding on here uh it's
going going to have a a thickness
of let's go with 1 in comma 75 in this
is not necessarily to hide the wood but
just to give it a little bit more
stiffness uh over time from stop it from
sagging so P push ball this direction 22
in Enter space bar bar triple click G
component enter I want these two pieces
to be a group so now I select one I
select them
both M for move move control brings up
plus sign along the blue axis I'll drop
one right there and drop another one
right there these are going to be on
some shelf pins so they will be fully
adjustable and right now we can excuse
me we can add the back piece so no sense
in drawing something that's already
there you just connect the dots pee Push
Pull
whoops um I never made the top a
component triple click G component
enter now I can do the
back beef push P this
direction and I want it to stop at the
bottom of this bottom shelf right there
space bar triple click CH component
enter and that's pretty much it that's
what I'm shooting for as far as this
design goes so
uh just to make it look a little better
I will control a to select it all go to
my wood
and let's see what this one looks
like that'll look all
right so that's going to be the
bookshelf um not going to be that big
it's going to be 42 in tall roughly 2 ft
wide and I'm going to have about 8 in of
shelf space here so
so uh it's going to be relatively
inexpensive and I'm looking forward to
this one
so that's it