德拉克講海軍歷史 海軍炮術 - 阿華級戰列艦的測距系統
王者风范
22粉絲
12 次觀看·2025年11月20日
大家好,我們之前看了關於火箭控制和尋找範圍的一整套
我們還看了火箭控制電腦的探測裝備
尤其是USS紐傑西的Iowa級戰鬥艦
還有我們看了為什麼你可能會失敗
當你以為你擋住了火箭 而你可能被擊中了
但我們還沒有在探討火箭控制電腦的一整套探測過程中做了一件事
就是到前線去看電腦採取的範圍數據和其他數據
然後將這些數據傳送到火箭控制電腦
當然,是這些數據的質素決定了火箭控制電腦如何探測
所以今天我們要來看看兩個探測系統
我們回到USS紐傑西
我們會去到Spot 1
是一般情況下最主要的尋找範圍
然後我們還會去到康寧塔
是一個防禦位置
如果Spot 1無緣無故失敗
我們會去到Spot 2
Spot 3
Spot 4
Spot 5
Spot 9
Spot 24
Spot 25
Spot 26
Spot 27
Spot 28
Spot 29
It's a half feet long and it's a stereoscopic rangefinder
And it's what you see projecting out of the arms or ears of this director
When you look at it from the outside
I am sitting right now in the pointer or levelers position
As you see here
There are a number of hand wheels and a telescope
And when a target was obtained by control
And by the Combat Information Center and by the plotting room
The bearing of that would be transmitted to the director officer
Who's actually standing behind me
In the after portion of the director
He could then verbally indicate the bearing
And I would turn
The trainer would turn his hand wheels
And we'll look at the trainer's position in a second
And bring the director on target
At that point I would be looking through my telescope
And if we were on target
I would align the crosshairs at the waterline of the target
Which is also the horizon
And choose a position
Usually approximately at the waterline
Where the fire control tower forward
On the enemy battleship target would be
I would then continue to move the hand wheels
To maintain that
Which would be sending a signal
Down to the Mark 8 rangekeeper
In the plotting room
That I was leveling
There are a number of other ways that I could level
If I was not able to see this
The stable vertical in the plotting room
Could send up a signal on these dials
And I would simply match the pointer
Maintaining the director level at that point
Of course it is important to maintain the level of the director
In order to get an accurate bearing on the target
There are also other controls for opening
The armored shutters that normally are closed
To protect the optics
And ventilation motors, etc.
The pointer is one of the persons in this director
Who can fire the main battery guns
And he has a firing key
Which my right hand is on right now
And a trigger at this point
If you were going to be using selected level
Or pointer fire from the director
Now the director is 116 feet above the waterline
And the reference point is actually in that central
Periscope director in the top level of the conning tower
So there is a vertical distance between them
And that has to be corrected for parallax
And so there is an instrument here
So I can set the range
Which will be transmitted actually on a series of dials
Which we will see in the trainer station
And based on that
That would match up the vertical parallax close enough
That then the Mark 8 rangekeeper
Could, when it is shifted over into automatic mode
Automatically maintain the vertical parallax
At the correct value
For whatever range the target was located at
We are also so far above the waterline
That when we look down at a target
Depending on the range
There is an angle, down angle
And that also has to be corrected for
That's part of the vertical parallax system
Now I'll move over to the cross levelers position
Now I am sitting in the cross levelers position
And this is the center position of the three
Forward operators in the forward portion
Of the Mark 38 director
I have a telescope
And this telescope can be switched
From one side to the other
And look 90 degrees either to the left
Or to the right
This maintains cross level
90 degrees across the level of sight
Again I would look through the telescope
Put my crosshairs exactly on the visible horizon
And move my hand wheels to maintain that
When I had it maintained
I would then squeeze this trigger on my left hand
Which would send a signal down to the plotting room
That I was maintaining cross level
If I could not see the horizon or it wasn't clear
I could get a signal from the stable vertical
Down in the plotting room
And follow the pointer
To maintain cross level
Also if we were firing in the selected cross level mode
In other words when the cross levelers optical sights
Came on the position that we wanted to fire at
In my right hand there is a firing key
And I could also fire the guns from the director here
I'll now move over to the most important
Of the three operators in the forward portion
The trainer's position
I'm now sitting at the trainer's station
Of the Mark 38 director
I have an optical telescope
But if you'll notice it's connected to this device
Which actually is connected through shafting
To the motor that stabilizes the range finder
This basically stabilizes this telescope
In the line of sight
And make sure that I can maintain level on the target
As I'm tracking it
Again upon an order
I could either turn my wheels to match
A target bearing that was transmitted
From the combat information center
Or from the plotting room
Or from control
Or the director officer
Could be looking through his periscope
Telescope
Train it on the target that he wants to do
Read off the bearing
And tell me to train left or right
In order to match the bearing that he sees the target
When I see the target in my sight
And I'm aligned on it
I then call out the words target
To let him know that I'm on target
And although they're missing
There's a key here
Which I would then squeeze the trigger of
To send a signal down to the plotting room
That I was now on the target
And then I would say tracking
And I would continue to follow
The bearing of that target
Keeping the crosshairs
Where they're supposed to be
That would send all that information down to plot
The Mark 8 Range Keeper
Would start computing a solution
When that happened
There is a light up there
That would come on
To tell me that they have a solution
At that point
I would switch to following the pointer
That the computer says
And I would be looking through my sights here
And upon given the order of match bearings
And switch to automatic
I would then flip a switch
Which would then put the mode into automatic
And now instead of the hand wheels
Tracking the target and rotating the director
This would all be done
Through a receiver regulating mechanism
That I'm actually sitting on here
And the computer would be training the director
I would still continue to follow
Looking through my telescope
And if the crosshairs did not maintain exactly
On position watered on the target
They started to drift either ahead or behind
I would then turn my hand wheels
To make a correction
That would send a correction signal down
To the Range Keeper in the plotting room
And the solution would be corrected
I would continue to watch
And once I got it
We would have basically
Know we have the correct solution
Now what would happen
If I could not see the target
This was night or optical conditions were poor
Well over here behind me
I have a Mark 13 radar scope
And this is the same type of gated radar scope
That is in the plotting room
And the director officer also has one of these scopes
So I could look through here
And turn my hand wheels
Until the target was in the exact center of the gate
And then I would continue to follow
On the radar scope
Even though I could not see the target
I could also make the same correction
If the fire control system was in the automatic mode
If I saw the target start drifting off the center point
I could make corrections with my hand wheels
To bring it back on to the center point
And that would send the same message down
To the plotting room
And the Mark 8 Range Keeper
To correct its solution
So essentially it almost does not matter
Whether it's day or night
The tracking system is the same
It's just whether you use optical
Or you use range finding
In addition there are again blower motors
There's things to open the shutters
For the trainer's position
And there is also one other piece of equipment
Which is behind here
Is that we are of course at a different position
Along the length of the ship
Than the central reference point
In the center of the conning tower
At the periscope telescope
So we have to correct for that for range
There is actually another person
Who sits in the after compartment
Who acts like a sight setter
And sets the range to the target
On the horizontal parallax corrector
He also matches pointer dials
And in the same way
That the pointer
The cross level of the trainer
Match dials to switch to automatic
He does the same thing
After that the Mark 8 Range Keeper
Continually corrects the horizontal parallax
If you imagine the triangulation
That we are using for
Solving the fire control solution
If the target is very close
The angle between this director
And the reference point is quite large
If the target is very long way away
The angle between this director
And the reference point is very very small
But it has to be corrected for
And this mechanism does that
Automatically and continuously
We are now in the after portion
Of the Mark 38 director
Behind the 26.5 foot
Stereoscopic range finder
Which rests on this
Giant thick steel arm
I beam in order to
Maintain rigidity
Which is required for the accuracy
Of the range finder
Normally there would be
Three people approximately in this position
One would be the operator
For the horizontal parallax
Who also functions as a talker
There would be the range finder operator
Who would actually be
Standing a little bit forward with me
But there is an open hatch right now
And he would be standing on that hatch
Which would normally be closed in battle
He would be looking through his eyepieces
And since he is a person selected
To have perfect equal stereoscopic vision
In both eyes
He would use the stereoscopic range finder
To find the range
There is another person
Who would be standing approximately where I am
Who would be reading off this dial
The range reading
Now that is automatically transmitted down
To the plotting room
But if that automatic transmission were to fail
Then the reserve range keeper
Who by the way also can be swapped
With the range keeper
Range finder operator
Back and forth when they get tired
Would also function as a talker
And could send that information down by voice
In addition there was a radio operator
Originally over in this position
When radar was added
It became more and more important
For a while radar components
Were actually up here in the director
They needed to be close to the antenna
Because waveguide transmission
Was not very good
In the early parts of World War II
Once waveguide transmission
Became much more efficient
All of that equipment was moved down
To the main scope
Which we have seen in the main battery plotting room
And only the portions of the system
That have the scope
That indicates the gated position of the target
And used for spotting of shell splashes
Were up here
So that relieved slightly more room in the director
But not much
Reaching forward here
You'll notice this handle
Now this optical range finder
Is normally stabilized in level and cross level
By a power drive
And the cross level is done by rotating the prisms
This can be fed either from the pointer
Or leveler
And cross leveler's positions optically
Directly from this director
Or it can be fed up from the stable vertical
In the main battery plotting room
And automatically transmitted to the range
To keep it on target in level
If however all of that mechanism fails
Then this handle can be pushed up and down
And you can manually rock this range finder
To keep it level enough
So that you can make a range reading
We are now in the after portion of the Mark 38 director
We are looking at the back wall of the director
In this area
There are basically a number of units
Concerned with communication and control
There is switches to select various circuits
On the sound powered phone network
So that the director can communicate with control
With the plotting room
With the combat information center etc.
They are also selecting power supplies
And selecting set up for the director
Selecting whether or not
For example the Mark 41 stable vertical
Down in the plotting room
Might be doing all the stabilization
And leveling and cross leveling
For both the director
And for the optical range finders
It also allows the spotting officer
Whose position we'll see next
To have communication verbally
With all of these other stations
I'm now standing in the last operator's position
This is the spotter
Who's also the director control officer
In the Mark 38 director
My right hand is on a periscope
That projects through the roof of the director
And can be trained in 360 degrees
This is used to acquire the target
And also to spot gunfire
Relative to the target optically
If for example the director control officer
Acquires the target
And wants to designate it to the director
He would acquire it in his periscope
He would then transmit the bearing
To the trainer
Who would bring it on to the target
The leveler and cross leveler
Would then make sure
That they have their crosshairs
Properly aligned with the horizon
In both level and cross level
And then the director
Could send all that information
Down to the computer
Or if the main battery plotting room
Was knocked out
And the range keeper was not operative
This could actually be sent directly
To the turrets
And then they could calculate
Their own solution
From the information
Being provided by this director
And the guns could be fired
Either from the director itself
Or they could be fired from down in the turrets
Depending on what was selected
All of the communications equipment
That you just saw on the back panel
Is mostly here for the spotter
To be able to communicate
With the rest of the fire control system
He normally has a sound powered
Blown headset on
And does that directly
But if that fails
The reserve range finder operator
Is also a talker
As is the horizontal parallax corrector
And either of them
Can transmit his information
Down to the rest of the fire control circuit
Now if the spotting officer
Is not able to see the target optically
Or if conditions are not ideal
Behind me
There is another one
Of the gated
Mark 13 radar scopes
And again
This would normally be positioned
By the trainer and the director
Who would be keeping the target
In the center of the field
But when the salvo arrives
Splashes that are 300 or 400 feet high
Occur as the shells hit the water
And those splashes are visible on the scope
And their relationship to the target
Is also visible on the scope
So that one can make spotting corrections
The mark 13 radar was so good
That one could spot individual shell splashes
And therefore you could count
The number of shell splashes
Versus the number of shells
That you fired in the salvo
If the number of shell splashes
Was less than the number of shells
That you fired in the salvo
You knew how many hits that you got
This gave terrific advantages
In spotting and range
Because that's very difficult to do optically
But the radar makes it almost easy
Now you may have been noticed
How crowded everything is
In the mark 38 director
Well there's a reason for that
All of this equipment
Is protected by an armored shield
Which is an inch and a half
Of STS special treatment steel armor
And this director
With the mark 13 radar antenna
Which sits on top of the director
About six feet higher
Than the optical line of sight
Weighs approximately 50,000 pounds
Or over 20 tons
Now remember we're 116 feet
Above the water line
So you can imagine the effect
That every pound up here
Has on the stability
Even of a huge ship
Like the battleship New Jersey
Or the other fast battleships
So it's important to minimize
The dimensions of this armor box
And the weight of all the components
In order to help preserve
The ship's stability
Luckily neither myself nor Dr. Skull
Suffer from claustrophobia
But we are not immune to heat
And since we filmed this
While the ship was in dry dock
And therefore had very limited shore power
There was no air conditioning
Up there in spot one
So by the time we finished
It was a little warm
So we were very grateful to get out of there
And head down to the comparatively roomy confines
Of the ship's conning tower
Which is where we'll pick up the narrative
We are now standing in the upper level
Of the conning tower of battleship New Jersey
And we are in the last
Of the director positions on board this ship
Spot one of course
Is the Mark 38 director
At the top of the fire control tower forward
Spot two is the Mark 38 director
At the top of the aft fire control tower
And this is spot three
Which is a Mark 40 periscope director
Located in the top level of the conning tower
In the original World War II design
This was the main battle station
Of the ship's main gunnery officer
Who controlled basically all of the ship's gunnery equipment
And all control was directed through him
This however in terms of its use as a director
Was actually considered an auxiliary or backup mode
If spot one spot two or the range keepers
In the main battery plotting rooms went down
This has the ability to track and bury a target optically
But does not have direct attachment
To the fire control radars
In order to track it and range on it
With radar
There are basically four operator positions here
And three periscopes projecting through the roof of the turret
In addition there are two additional periscopes
That are located in the next level down of the conning tower
That project through its roof
And then through the roof of this level of the conning tower
Let's first start looking at
The most important periscope
The one in the center of the director
Which is where the trainer and the spotter
Who is also the ship's gunnery officer stand
I'm now standing at the trainer's position
His hand wheels will rotate the periscope in front of me
And he can optically line up his crosshairs
On the water line of the target
Now in order to compensate for the ship's rolling and pitching motions
This periscope and director system
Is mechanically geared to a level and cross level periscope
One on the right side and one on the left side
Either one of those periscopes can perform
Either the level or the cross level function
If one is performing the leveling function
Then the other is switched 90 degrees of rotation
To perform the cross level function
If the view from either the leveling periscopes is blocked
It then can reverse and become the cross leveling scope
And the cross leveling scope can become the leveling scope
So it's a very versatile system
There is also on this particular periscope
The ability to transmit bearing and tracking information
Down to the main battery plotting rooms
So that that information can be run through the Mark 8 range keeper
And the level and cross level information
Can also be sent to all the other components of the system
Including the turrets and the plotting room
To substitute if the stable verticals
In the plotting room are not operative
Or if optical conditions are considered so optimal
That it's better done here
Than down at the automatic stable verticals
Now this periscope has a mirror system in it
So that its image is also transmitted to the other side
And I'm now going to move around to the position of the spotter
And you'll see that there is another periscope here
This is where the gunnery officer would sit
Originally when this was first built for the fast battleships
This periscope was connected to a spotting scope
Basically which looks like a stereoscopic range finder
And actually has a stereo viewing function
But does not actually function as a range finder
Because it does not have a range transmission unit in it
It is used to spot the target
And then spot shell splashes
And see how far from the target they are
This works very well
If the shell splashes are to the right or left of the target
In other words they miss in deflection
And there's a graded scale where you can measure that off
To get the exact distance that they fall
However it is very difficult to spot
How short or how long splashes are
Splashes behind the target
Oftentimes cannot even be seen where they hit the water
So they are very difficult to tell how far they are
Long from the target
And even the ones that fall in front
Where you can see exactly where the shell hits the water
You still have to use a stereo vision estimation
Of where that is
And most people found that fairly challenging to do
Once radar was available
That provided a much better view
When you had precision radar
And you could actually see on a scope
As if you were looking down like a bird
At where the shell splashes were
Much much better for determining
Spotting by range
This of course is being trained
And because it's connected to the leveling
And cross level periscopes
This is kept on level
So the spotter is having a continual view
Of the target through this
Now in the other fast battleships
Of the North Carolina and South Dakota class
This director unit
In addition to sending electrical signals
Down to the plotting rooms
Also had a mechanical shafting
And there was an auxiliary fire control computer
Known as a Mark III
Sitting about here
Which was mechanically geared to this
So this could take over
The entire fire control problem
In case of an emergency
With the plotting rooms being knocked out
Remember that the North Carolina
And South Dakota classes
Have only one main battery plotting room
If it was so unfortunate
As to be knocked out by battle damage
This would have to take over
The whole fire control solution
The Iowa class however
Had separate forward
And after main battery plotting rooms
Giving much better protection by redundancy
And therefore this station
Did not really need to take over
The whole fire control problem
And therefore it did not need
Its auxiliary computer
And this opened up a great deal more space
In this room for other equipment
Such as radar
Now on the North Carolina
And South Dakota classes
And originally on the Iowa class
There was a radar
That actually was on the top roof
Of this level of the conning tower
It was a Mark 27 radar
Which originally was a range only radar
It would only give you range to the target
This could substitute in part
For an optical range finder
Which this station does not have
However during World War II
Some very clever radar men
Figured out how to rewire the Mark 27 radar
So it would produce information
Both for range and for bearing
And would actually give you a B scope
Or plan position indicator
The typical radar sweep scope
That we all think of radar
Was actually be able to be produced by the Mark 27
This made it a great deal more useful
Even though its bearing readings
Weren't really accurate enough
For full radar control of gunnery and bearing
It did give range
And there were some additional functions
That it could do
It could function as a backup navigation
Or surface search radar
Now that it had this B scope presentation
So that made the Mark 27
Auxiliary fire control radar here
Much more useful
Now as you remember
This station was intended to be
The primary battle station
Of the ship's main gunnery officer
The Mark 27 auxiliary radar
Provided some radar information
But it really was not optimal
So that was removed later on
In the Iowa's career
And instead
Scopes for the Mark 13 fire control radars
Were installed here
One for the forward radar
And one for the aft radar
Again these are the same gated scopes
That we've seen
In multiple areas
Of the fire control system
Putting the target in the center
So it can be tracked there
And also allowing you a view
Or window of all of the shell splashes
Around the target
This is actually the information
That probably was most valuable
To the ship's gunnery officer
In terms of spotting
Better even than he could do
Optically especially
In the range function
Okay on the back portion
Of the upper level of the conning tower
Are control and communications
Information
There are telephones
To the ship's main circuit
There are multiple jacks
For sound powered telephones
Because this position
Is on the main battle circuits
It's also on the main fire control
Control circuits
So it needs to have a lot of communication
With other stations at the ship
It also needs to communicate
With the turrets
And the turrets need to communicate
Back with it
And we have a set of turret ready lights
Up here
Each one of these has a lamp
Showing whether the turret is not ready
Or whether it is ready
And depending on
What type of salvo pattern
Or firing pattern
You're going to use
You're going to be looking for
Whether all three turrets are ready
Or whether only selected turrets
Are ready and able to fire
There are also
The ability to fire the guns
From here from both the
Levelers and cross levelers position
And they also could be fired
By the ship's main gunnery officer
At his spotting position
If he wanted to
Moving over further
Again we have
Turret train indicators here
We also have information on the ship's
Secondary battery directors
And where they're trained
We have a gyro compass
Showing the ship's course
And we have multiple rotary switches
To set up various
Fire control positions
Kind of an auxiliary switchboard
And also many of these
Are also rotary switches
For all the communications circuits here
I'm now standing at the left hand
Level or cross level
Stabilization periscope
That is mechanically linked
To the primary training
And control periscope
I have again a set of hand wheels here
And I'm looking through my eyepiece
If I'm doing leveling
My crosshair is vertically
Should be on the center of the target
And my horizontal crosshair
Should be exactly on the waterline
Of that target
Which is the same thing as the horizon
If I'm the cross leveler
I should be looking at the horizon
And keeping my crosshairs
Exactly on the horizon
I have two triggers here
One trigger is to signal
To the transmitter of this scope
Which is transmitting
That bearing information
That I am at level
And therefore the information
That's being transmitted is correct
The other is a firing key
In case we were going to use
Selected level to fire the ship
And I would be turning my hand wheels
And when I was exactly in the right position
I would then squeeze this trigger
And if the circuit was rigged up in that manner
That would fire the guns
The right hand periscope
Is essentially identical
And can perform exactly the same function
If this one was set for level
That one would be set for cross level
But they could be switched at any time
Upon direction of the gunnery officer
Now the conning tower
As you might remember
Is an armored cylinder
With walls up to 17 inches thick
And how do you see out of it
Well not very well
There are slits cut in it
Which you see here
Notice the tremendous thickness of the armor
This however does not give you much of a view
And you have to move around to each slit
To see even a small window
Because of this limitation in vision
Many commanding officers
Did not like to use the level below
As their main battle station
Because they could not see very much
And even some gunnery officers
Did not prefer this
And they preferred to be in other positions
Because they would have a better view
Or some of them like to be
In the main battery plotting rooms
So that they would be able to see
All the information going into the rainkeeper
And have the most information
About the gunnery situation
Unfortunately or unfortunately
That was not the approach
Of the world's most obvious terminator
That was in fact the crane operator
Signaling that if we wanted off the ship
That was our time to leave
And so we're going to wrap up there
You've now seen a bit more of what's involved
At the sharp end of the stick
When it comes to actually spotting the enemy
Locking onto them
Tracking them
And supplying all that data
Down to the fire control computers
So that the big guns can do their business
Hope you've enjoyed that
And see you again in another video
That's it for this video
Thanks for watching
If you have a comment or suggestion
For a ship to review
Let us know in the comments below
Don't forget to comment on the pinned post
For dry dock questions
Control and communication circuits
There is links to sound powered phone
Did we lose our
That's it
Okay
Hopefully we've got enough to finish here
We've got enough line
Okay
Let me start over again here
Okay
Not in your eyes
Yeah that's good
I can use the periscope here to keep it out of my eye
Okay that's it
So we'll use
