Hey folks, this is a Stanley Bailey number 5 hand plane.
It doesn't belong to me, it belongs to a friend of mine, but it's definitely seen better days.
Every bit of it's here, it's just there's something wrong with everything.
It's all beat up and just old and dingy.
So today I'm going to get it back into working order and also try and make it look good while
I'm at it.
Let's do a quick glance over of the original, the V4.
The handle is beat up right here, some of the finish is missing, a couple nicks here
and there.
This front knob is all beat up and destroyed all the way around and it wasn't even really
tightened, which that's part of the screw, no big deal.
This side doesn't look much better and the bottom is in pretty good shape.
There's no major pitting at all, I don't think there is anyway.
The blade is, I think, quite rusty just from the looks of it.
So let's start taking this apart.
This front handle, I'll remake another one of these, there's some surface rust here.
This is the lever cap screw, this is the lever cap, it's in pretty good shape.
The blade is attached to the chip breaker with this screw and it's all surface rusted.
Not crazy bad but there are definitely some dings in the blade.
And this piece right here, this assembly is called the frog, I'll remove it as well.
All of this looks pretty good, there's just a little bit of surface rust and nothing crazy.
And of course the rear handle or tote, whatever you want to call it.
There's many different ways to remove rust off of metal and there's pros and cons to
each one.
I'm going to use just regular cleaning vinegar, household vinegar, and to submerge everything,
this is a 4 inch piece of sewer and drain PVC pipe and it'll be probably the most efficient
use of space for all of this metal to sit in while the vinegar does its magic.
The vinegar does a really good job at removing all of the surface rust and breaking up all
of the deeper, the larger pieces of rust that are on there so we still need to gently
wipe all the pieces nice and clean and all of the crap that's on them should come right
off.
For the spots that are a little bit more stubborn where the paper towel won't wipe off, I'll
dip them back in the vinegar and use a brush on an angle, dip it again, and now every bit
of that should be gone.
I'll repeat this with all of the pieces that I have left.
Once all of the pieces are nice and clean, it's important to get all of the vinegar off
of the metal, that way it doesn't continue to eat away at it and to do so, I rinsed everything
off underneath warm water and made sure everything was absolutely dry, that way the warm water
doesn't add to more rust in the future.
I taped off a couple areas inside the plane that need to have bare metal exposed, such
as where the plane body meets the frog and for the rest of it, I'm just top coating everything
with another coat of black paint.
Next up are the handles and they should be extremely simple to do.
The first one, the front handle, is just a simple turning and I've created a blank that
is nice and square on all six faces and the top and bottom face are exactly parallel and
the center points line up with one another.
That's important for me because once I get this turned on the lathe, then I'm going to
take it to the drill press and drill the top and bottom counterbore and I want their
center points to line up in the middle and that should be pretty easy to do.
For the rear handle, I could use the old handle and trace it out and then just go from there,
however, someone sent me a perfect template that you can also find online for this exact
same plane, this Stanley Bailey number 5 and I can just attach this to my blank and cut
it out following the instructions on the template.
So, it should be extremely simple to do.
All of the dimensions and holes and placements and such are included in the template, so
before I can start cutting everything out, I do need to get my material down to a 4 1⁄2
by 4 3⁄4 inch square and I'll use the crosscut sled on my table saw to do this.
Each one of the handles is mounted onto a piece of threaded rod and the rod goes right
through the handle and to secure the handle to the plane, there's a piece of brass that
is screwed onto the top of it and to check the depth of my counterbore on the new handle,
I can use this piece of brass onto the threaded rod upside down and push it through the handle
to make sure I'm at the appropriate depth before drilling my through hole all the way
through the handle.
Before leaving the drill press, I'll switch back and forth between the front and back
handle drilling all of the necessary holes and if I'm not mistaken, there was five different
drill bits that I needed to use, so there's a lot of switching back and forth and back
and forth depending on the process of what hole I was trying to drill.
I made the bottom cut on the back handle with the table saw and a crosscut sled to make
sure that that cut is absolutely perfectly straight and the rest of the cuts can be made
on the bandsaw before final shaping with some hand tools.
I used a pencil and my finger to trace a little bit of an offset line on both of these faces
that need to be rounded over and this is just a guideline to guide me with the rasps to
make sure I try and make things symmetrical and a little bit more even as I go throughout
the rest of this handle.
To preserve the natural color of the wood and also give the handles a little bit more
protection long term, I'm using a film finish and I'll just spray on a couple coats of satin
lacquer.
I forgot to mask off the top edge of both of these sides, so I do have some paint down
there that needs to be removed and I'll just use some regular sandpaper for it.
And then after that, I can put some self-adhesive sandpaper onto my table saw, which is a known
flat surface, and use that to make sure that the bottom surface is nice and flat.
After sandpaper, you could polish the plane up to as high of a polish as you really want,
but I think I'm at the point of diminishing returns.
This is a side-by-side comparison of the plane I'm working on next to a low angle jack plane
that is relatively new, less than a year old.
It hasn't seen a lot of abuse and they look pretty much the same, not much difference.
So I think right here is where I'll stop with polishing and now I can focus my attention
on the blade before assembly.
The cutting edge of the blade has a couple deep dings in it, so first I'll use my grinder
to remove all of the major defects.
And while I am using the grinder, I am making sure to check my progress with a square occasionally
to make sure that the edge that I'm left with after the grinder is perpendicular to the
sides of the plane blade.
Right before sharpening, I do want to polish the blade, chip breaker, and lever cap.
And to do so, I'm going to use a polishing wheel with a little bit of buffing compound
on my lathe.
I'm not going to go into a full-blown demonstration on how to sharpen an edge because there's
so many different techniques and videos out there on how to obtain a sharp edge.
But I will say I am using Paul Seller's recommended diamond plates and I'm using Rob Cosman's
method for sharpening.
And once the front edge is just absolutely razor sharp, you should be able to feel a
burr on the backside.
And you can remove this burr and sometimes it comes off in a nice long piece like this
one right here.
And I'm not exactly sure if it's going to show up or not.
But this is a nice full-length burr that was on the entire backside of the cutting edge.
And this tells me after this is removed that this is razor sharp and ready to go.
The final step before assembly is to go back to the buffing wheel and polish all of the
brass pieces.
All right, I do believe I'm ready for assembly.
So really quick, I went ahead and put some, just a couple drops of regular 3-in-1 oil
on all of the threads for everything here.
And the first thing to be installed is this screw that will be below the frog.
Now the point of this screw is to adjust the frog forward and backward and therefore adjust
the plain blade forward and backward.
And there's a slot right there on the screw and it interacts with this clip.
So it goes in place like so.
And like I said, as the screw is advanced, so is this, back and forth.
And this gets secured to the bottom side of the frog.
And I may not be able to show this as I'm putting it in place because this screw is
pretty small.
So this gets screwed on and it will sit like so.
Before we do install it though, I want to put the adjustment screw on the backside here.
It is reverse threaded and I need to make sure that as it gets installed, as it gets
screwed on, that it captures this horseshoe shaped piece that on the other side adjusts
the plain blade depth.
So now this is ready to be installed and making sure that this bottom piece lines up.
Now I can determine how far forward and backward I want the frog to be.
And I can see that this reference surface that the plain blade will be on is too far
back compared to the reference face on the mouth of the opening down here.
So I will advance this screw down on the bottom and I may have to adjust this back out a little
bit once I get it all installed, but I'm going to try and get it a little bit closer.
And when it's all said and done, the closer this is forward, the more closed this mouth
position will be down here and the smaller the opening, the less size of a wood shaving
can come through it.
So if you want to take very, very thin smoothing type passes, then it's ideal to have this
thing closed forward.
For just general use, it's not that big of a deal.
So now we need to secure this down and two screws and two washers.
I'm just eyeballing this to make sure it's not twisted one way or the other.
This looks pretty straight to me.
So I'll tighten these up to lock the position of the frog.
And of course you can always take the blade off and readjust the frog as needed.
Now I'll spin this around and install the rear handle next.
And this requires this long threaded rod and a brass screw on one side, or a brass nut
or cap, whatever you want to call it, on one side to go all the way through here.
And this will go into this screw hole here.
There's a small one over on this side that I can get started over here on the front of
the handle.
The front handle is installed the same way.
We've got another brass cap with threaded inside and we'll put a threaded rod inside
it.
Put it through the handle and onto here.
The blade is attached to the backside of the chip breaker with this short and wide screw.
So on the backside of the chip breaker, this screw is threaded on just barely.
And then the backside of the blade gets attached to it and they swing into place so that the
chip breaker does not touch the cutting edge.
You don't want to damage the cutting edge.
But you do want it to be like a 16th or a 32nd of an inch away from the cutting edge.
And this can be changed depending on how you want the plane to perform as well.
Making sure it's nice and square, I can tighten it down.
So now this assembly is ready for the plane.
With the back side of the blade up, making sure not to ding the front edge of the blade,
can be set into place.
And there is an adjustment lever back here that rides inside this slot of the blade.
So making sure it is properly in place before the lever cap is installed.
And the lever cap, this is pretty loose, holds everything together.
It's still really loose.
So with this lever down, I can tighten the screw.
And this needs to be tight enough so that you can still adjust this with one finger
as you're working.
I think it can be a little bit tighter.
And that's good.
So there you go.
The assembled, completed plane.
Alright, this is really hard to show on camera so hopefully you follow along with me.
The plane is upside down and the front handle is facing the camera, or facing my eyes.
And you can see that the plane blade is not sticking through.
So I'll advance the blade.
Sorry for the shaking hands.
So the blade is sticking through.
And from here, this is where you can set the angle.
So if the blade is skewed to one side when you first start, you'll be able to see.
Like right here, you'll see that the left side is quite a bit higher than the right
side.
So you have this handle back here that you adjust left or right to adjust the blade.
So if we are, let's go back to where we were, we're left side high, then you can pinch the
blade towards the high side and it will bring it down a little bit, which results in the
right side coming up.
And all you have to do is eyeball this to be visually parallel with this bottom surface.
And kind of hard to see through the camera here.
Once you have it close, just back off the depth of the blade so that the blade goes
back into the plane and it's not sticking out.
As I was just testing this out, the mouth of the plane kept getting clogged up, causing
me to have to remove the blade in order to clear it.
And that's not what you want.
So this tells me that the frog is too far forward in the body.
So to fix that, the lever cap can be removed, the blade can be removed, and the two screws
holding the frog in place can be slightly loosened.
And then the screw down at the bottom to adjust the frog depth can be backed out just a little
bit.
And I'll back this out by about a sixteenth of an inch.
And that looks good.
Tighten these back down.
There are different plane styles out there that allow you to do this without removing
the blade, but this one is not one of them.
So now we can go through the process again of setting the blade in the appropriate, or
having the appropriate angle on the cutting edge of the blade.
Alright, that's good.
You can very easily dial in the angle of the blade with a scrap piece of wood.
And to do so, just advance the blade so that the middle is getting just a little bit of
shavings.
There you go.
And then put the whole plane to the left or to the right, and only try and use that side
of the blade.
In this case, the left side over here is not making any cuts, and the right side isn't
making any either.
I'll advance it just a little bit.
The right side is making just a little bit of cut, and the left side about the same amount.
So from here, if one side was cutting more and the other side wasn't cutting hardly at
all, then you'll know that that side is further down, and you can adjust it back here.
But this is cutting just as it should.
In the end, the plane works fantastically, and it doesn't look that bad as well.
This is the second plane that I've gone through this entire, I guess, restoration process
on.
The original wasn't incredibly bad, but the outcome definitely does look a whole lot better
in my opinion.
And if you'd like to have some more information on this entire process and links to other
sources, then be sure to check out the website article linked in the description of this
video.
And I'll go into further detail explaining everything that I personally know and pointing
in the right direction for stuff that may be a better source of information.
Thanks for watching.
You guys take care, and have a great day.