I was milling up some hickory yesterday
and was pleasantly surprised when I
found one board in the stack
that looks like on the surface it had a
little bit of curl to it this is a rough
sawn piece and you can see some curl in
it but you also see a lot of tear out so
I cut out a small section of this off
this board over here to go through the
milling process and see if I could get a
nice surface without a lot of tear out
luckily I was able to do so with a very
very very slow pass at the jointer and I
don't know if you can see on camera but
right here we've got a lot of really
really nice curl to it and on the other
side somewhat there's still quite a bit
of figure in here but I think this piece
would be a perfect candidate somewhere
around in here for maybe a small sliding
lid pencil box something like that so
I'm going to use this and see what we
can come up with
I'll start by using a hand plane to
clean up one of the short faces not only
will this give me a nice flat face for
the rest of the milling process but
it'll also allow me to understand how
this particular board is going to react
with a hand plane I think I'm gonna make
a pencil box something that's about
seven inches by 3 inches roughly and has
a three inch height so I'm going to cut
that three inch height out of the board
right now and then I'll resaw that piece
at the bandsaw to get all of my sides
hello
just to get the pieces down to the exact
same thickness I ran them through my
planer with very very shallow passes
this hickory I know from experience
tears out horribly on this planer
especially with all of this curl so I'm
just feeding them one after another with
just a slight advancement of the depth
with each and every board I went ahead
and taped the two pieces together just
to maintain grain orientation just to
make sure that everything lines up once
again and also I don't need all this
board I need to cut it to its final
length which is one short side plus one
long side and I'm thinking eleven and a
half inches should be fine even with the
curve cuts so I need to avoid this chunk
of tear out that I made last night or
yesterday here in the shop and that's
pretty much it on this side on this side
there's a knot right here which is
pretty much unavoidable no matter which
direction I come from and then I also
have this weird-lookin circled piece of
the grain right here that I want to
avoid so I know that if I just say two
fingers for this grain this tear out
right here plus eleven and a half that
is less than the distance to this ugly
spot that's going to be good enough I'll
just cross cut right here and then add
eleven and a half inches
anytime you put a board on end and resaw
it what you get is those inside faces
becoming a book matched set and anytime
you have a book matched set it is the
closest you can get to having a mirror
image side-by-side now you know take
that with a grain of salt here there's
there's a lot going on with this grain
for example this darker streak right
here isn't really dark on this side and
this darker streak over here isn't
really dark on this side but the overall
flow of the grain should be symmetrical
and you can see this these two veins
kind of get narrow right here widen out
right here and then you continue all the
way up so there is a lot of symmetry
going on and if you have a symmetrical
edge up against each other and you
rotate the pieces in I guess the
opposite directions then you have once
again symmetry over here whatever this
side is should be flip-flopped on to
this side a mirror image and we can use
that for to our advantage with the box
sides so if I put this back together and
instead of just opening it up like a
book if I put one side by side and I now
have the matching faces on the outside
so the grain should wrap all the way
around this and to use that as our
advantage remember that a box has a
short side a long side short side and
alongside the rectangular does anyway so
what we can do is we can cut on this
piece a long side then a short side
continuing the grain around cutting a
long side and then a short side and then
if we miter these together then you
should have a continuous matching grain
all the way around about a year and a
half ago I did not know that and thanks
to some handy research and learning from
other people now I do because I already
cut both of these pieces to the exact
same length all I have to do is cut the
long side out of each one now remember
each one of the along sides
needs to come from the opposite end of
each board
so pretty much no matter what if I if I
don't follow a plan I'm gonna do
something out of order if I just come to
the shop and just just build something
on the fly and have fun
I always do something out of order in
this case it's not the end of the world
but it would have been much better as
far as consistency goes if I cut all of
my grooves for the top panel and the
bottom panel will live in bottom panel
before separating all of my pieces I can
still cut it now but it's just a it's
just a timing thing or sequence thing so
I've got the blade set to 45 degrees
right now I'll go ahead and cut all of
my miters and then go back to 90 degrees
and cut those two grooves all I want to
do is establish a 45 degree angle I
don't want to reduce any length at all
so to help me do that I'm going to use a
stop lock
before making the miters I made
identical marks on this corner for each
board and then on this corner for each
board so I know that these two pieces
form a corner these two pieces form a
corner all of the markings face up that
means there's only one way to assemble
this and it's like so all the miters
turn out great so now I can go ahead and
cut the dados
Hartwood and hickory is more of a
reddish brown color and that's where all
the box sides are made out of and to
contrast that I'm making the top and
bottom panel out of the sapwood in
Hickory and SAP wood and Hickory is it's
kind of like this bright light color and
I made it just a little bit too thick
for these grooves that's because I want
to use a card scraper to clean these
faces up and really get them down to
size sizing the panel is very easy the
distance from right here to right here
on the grooves is our width and then
from right here to right here is our
length now because the panel is so tiny
and it is quarter sawn so most of its
expansion and contraction will be in the
thickness I'm not going to decrease the
size of the panel at all for expansion
and contraction
it'll be fine glued in place just as I
thought might happen the grooves weren't
as consistent as I wanted so I did have
to finesse both the top and bottom
panels here and there to get them to be
absolutely perfect that's okay though I
did get everything lined up all the
miters look good and each one of the
panel's has a little piece of blue tape
to designate its exact orientation so
everything looks good I'm going to take
it apart use some blue painters tape as
clamps and glue this thing together
this is a very easy and uneventful
glue-up so long as you you know check
all your boxes and no pun intended
before you before you do the blew up
distracted oh yes so this is these are
relatively thin sides they're not that
big and it is really chilly here in the
shop so I'm going to let this sit
overnight and let the glue just do what
it wants to do and fully cure before I
stress the joints any further it is the
next day all the joints look really good
and now on to the part of the project
that I'm actually really looking forward
to and that is to make some really
really tiny splines to reinforce the
corners and add a little bit of visual
interest this is a scrap piece of wood
that I was experimenting with to try and
make extremely tiny kerf cuts and
therefore tiny splines so the distance
between these two over here is about 1/8
of an inch which is the distance or the
thickness of my table saw blade so if I
was to cut this kerf cut on my or this
spline cut on my table saw I'd be forced
to have a really wide spline there I
could use a thinner blade but you can't
go that thin not this thin anyway these
were made with one of these Japanese
pull saws a very very very thin blade
and I want to use this size spline on
the box
however the colors are gonna be reversed
my box it has a darker color for the
body and a lighter lid so I'm going to
use lighter splines and and hopefully
they'll stand out there are a couple
advantages of using a table saw to make
splines and that is basically due to the
fact that you have to use a jig on the
table saw you have to have some way to
hold the piece as you push it through
you can't just freehand this so with a
spline jig on the table saw you have
basically two reference planes number
one you're going to reference the side
of the box up against the fence of the
jig or the fence of this saw and that
will position the spline
left and right and then also you're
gonna have a reference face off one of
the sides of the box to determine that
45-degree angle so with that you'll have
pretty much consistent results all the
way around every one of your splines
will look the same so long as you use
the exact same setup for every one of
the cuts we don't have a jig or I don't
have a jig for the handsaw so I'm just
free handing these and instead of
creating a jig it's just gonna be a lot
easier to make some reference marks and
then just stop at those marks to
establish the depth of cut I made a mark
one half of an inch in from each edge
and then extended that line all the way
across the entire face to establish not
only the location of each one of the
splines but also give me something to
visually track as I cut the splines I'm
using a marking gauge set at about 3/16
of an inch unlike most other times where
you use a pencil for layout here we want
to divide the line in half split it
right down the middle rather than
leaving it on one side or the other
so the goal is to join beacons
consistent as possible at the cutting
angle and get down to the reference
lines at the same time on both sides if
we cut a little bit like this we're
going to have down to the cut line on my
side and we cut like this we'll be down
to the cut line on the opposite side and
therefore we're leaving a little bit of
a hump in the middle so consistent
longer strokes
all right I don't need a lot of material
here for the splines but I do want them
to be somewhat consistent and thickness
so I've cleaned up one of these short
edges of this SAP wood board with my
Jack plane and now I've got my number
seven set really aggressive way more
aggressive than what I would ever use it
in any normal operation so what I'll do
is wow its aggressive enough that this
is rocking back and forth quite a bit
anyway I'll start the cut maybe if I can
do this Hickory break this off who stay
in the groove alright break it off and
test it in the kerf still that's a
little thin I'll advance the iron just a
little bit and try and push this thing a
little bit further break it off and test
it in the kerf I think that's it all
right I think that's a perfect fit this
is probably enough but I want to have a
little bit more for reassurance here so
just to finish the cut maybe man that's
ridiculous okay this is plenty enough
kerf material for what I need a little
bit of glue on the spline and I want to
work fast here because this glue will
make the wood expand which is not what I
want and don't want this spline to be
any thicker than what it is because it's
already delicate and now I can start on
one side and kind of hopefully pull my
way through and use the glue somewhat
like a lubricant before it starts to set
up if possible and with a delicate
process
can't tell if I'm all the way down on
this side okay I am yeah so now we will
remove the excess glue from both sides
trying to move quick and then use a
chisel with a paring cut too let's see
how to do this left-handed chisel with a
paring cut just slice that side off and
then slice oh man this is odd
left-handed slice this off and there we
go not too shabby
I only used two splines per edge for a
total of eight of them and they look
really nice but I didn't want to go
crazy with them and really distract from
the wood grain here so just two per edge
that's all I'm gonna do now I need to
separate the top from the bottom or the
lid from the body of this box and I
think it would make most sense if we try
and make a kerf cut the table saw to
slice this knot right in half and
hopefully hopefully remove as much of
this darker spot as possible to make
this process just a little bit safer at
the table saw I like to set the blade so
it does not cut all the way through the
material for these short faces and then
I'll raise the blade just a little bit
so that it does cut all the way through
and then cut the long faces of the box
that way a shoulder or the cut line is
established all the way around but the
pieces aren't being separated just yet I
don't want them to separate as they move
through the table saw so then I can take
the box to the workbench and safely
continue to cut or complete the cut with
a handsaw
because the green is going all the way
around the box that means the cutting
direction is going to go all the way
around the box on the top as far as
clockwise or counterclockwise and that
means to get a nice smooth surface all
the way around and verify that we don't
have any little minor high spots we can
use a smoothing plane to very carefully
go all the way around and make sure
there are no high spots
do the same thing on the lid real quick
for the interior lining I'm using curly
maple I just need to cut these pieces to
an appropriate length a little bit
oversized and then sneak up on an exact
fit with my shooting board making a 45
degree miter not only does this interior
liner brighten up the inside of the box
and maybe make it feel a little bit less
small it also provides a registration
point for the lid so it can close nice
and even all the way around for surface
prep all I'm using is a scraper and I'll
use that on all of the exposed faces and
then I'll use a simple top coat to bring
out the beauty of the wood
you
you
you
you
you
you