This is three quarter inch melamine and the reason I'm using it is because it's the least expensive
engineered panel or sheet that I can get locally. That for the longest time was three quarter inch
we're talking about the three quarter inch thickness three quarter inch MDF and that is
now $45 a sheet. This I believe I paid $32 a sheet and I've got some some non-aesthetically
important projects that I want to get done so I don't care what it looks like I just want a three
quarter inch panel that is stable that I could use. So I picked up some of this to experiment
with. This is my horizontal belt sander and I've had it for a couple years now. It's a Hammer HS950
really really nice machine topic for another day. But the belts that it uses I've never had a storage
spot for them so as this has moved throughout my shop the belts have been put here and put there
and put here and put there and they lived right here for far too long. My daughter is starting to
run them over with her tricycle so today's objective is to make a storage solution for
these belts. Right next to the sander is my dust collector and this looks like a very convenient
spot to store the belts because it's right next to it. And also the frame that the dust collection
system is sitting on the dust collector is sitting on is kind of skeleton in design so it's it's wide
open and looks like a good structure to build upon. My thinking is to put some type of panel
on the front of here with some type of hangers on the top to slip the belts over and have it
at a height in which the bottom of the belt is somewhere right here so it does not interfere
with the use of the dust collection drum. On this side of the dust collector as you can see I hang my
my aprons up over here I have some PPE that I always just drape over one of these rails
and I've gotten the bad habit of storing a bunch of randomness on top of the barrel which I don't
want to continue so it would be very convenient if I'm already building a wall over there to build
a shelf to go right here for the little bits of randomness as well as my safety glasses PPE and
stuff like that. So a wall over there a shelf right here. I don't have a vacuum table so I find that
just one washer head screw on either corner or a clamp is all that's necessary to hold this down.
I prefer screws rather than clamps because I find that the clamps actually compress the
spoil board a little bit whereas the screws have a physical vertical barrier to stop it from
shifting as well rather than just friction from the clamp. This is the cart that I made for my
CNC laptop as well as some bit storage and just various other storage but it uses two main joints
for all of the construction a mortise and tenon joint and a box joint or finger joint whatever
you want to call it. So here you can see the tenon on the drawer bottom sticking through a mortise
on the drawer front. Same with this over here you have a tenon on the drawer runner sticking through
a mortise on the case side and on this side over here you can see box joints finger joints where
the side piece extends all the way through the thickness of the front piece and vice versa. Once
you have the material thickness dialed in and you use that material thickness for all the modeling
for designing the actual components cutting it out is and then assembling it is very satisfying
because everything just just kind of clicks together and it's it's just a very satisfying
assembly process. But you need to know the sweet spot for the material thickness to use to actually
model on the computer because you you don't necessarily want to just use calipers and
measure for two reasons number one the ends or the edges where the calipers can actually you know
fit on some sheet goods is typically a little bit thinner than the center area so that's number one
number two you don't necessarily want to have a one-to-one fit for for the sizing because that
could be too tight you may want to have just a little bit of play not so much that the joint
becomes sloppy but enough to where it's a little bit easier to assemble. So every time that I use
new sheet good I'll run some tests to determine the exact thickness that I need to model with
for whatever project I'm going to use going forward with that particular material I'll put
it in a spreadsheet so I always have it but I need to get that done because I've never used this
particular melamine panel in this particular way. The average thickness according to these calipers
is about 0.762 inches but this is on the edge where it's always a little bit thinner so I'm
going to start the experiment at 0.765 thickness. I went ahead and cut several pieces to do all the
testing and let's talk about the results. So there's a few things that I wanted to test number
one the quality of the edge on a conventional versus a climb cut, number two the the quality
of the edge with the bit that I'm using, number three the size of the the width spacing of the
based upon the tenon which will also correlate to the length of the tenon and then also the edge
what can I do to the edges to make them a little bit more durable I don't want these sharp edges
on something that is just going to be exposed I'm not putting solid wood edge banding on this so I
want to make this a little bit more a little bit more durable and I think a simple roundover will
solve that so what bit can I use to create a nice roundover without it chipping out. So a few tests
but let's just jump right into it this is my gauge block I guess you could say with different sizes
I started with 0.765, 0.764, 0.763, 0.762 these are all inches and then one open-ended slot right
here because sometimes these fit a little bit differently than mortise and tenon joints so
this is the male piece to this and I'm going to do all of these just I'm going to show you them
with it seated just like this not seated all the way down so the way I'm going to test this is it's
partially seated and if I'm not coordinated here there we go I if I put it in just a little bit
and just wiggle the top that's how much movement I have a little bit more than what I want
so I'll go to the next one 0.764 barely started in the joint it's better but still a little bit
of wiggle 0.763 inches this one I think is the money so it's again just barely in there
and little to no wiggle very little wiggle but at the same time you can see the joint properly so
0.763 I think is the the number now I did this slot at 0.765 it fits just fine so I'm going to
slide all this away and talk about this little slot joint I cut another one at 0.753 after
getting the information from that first piece and this is the mating piece and what's cool
about these joints is they slip together kind of like legos and this right here
that is so satisfying just a nice perfect perfect joint but what I like to use these for
these particular style joints is when you have gravity working in your favor so in this case
a slip fit is okay there's no mechanical fasteners necessary if this goes with gravity
so gravity is going to push this down or keep this push down and this would work well with
something like an arm sticking out an arm sticking out quite a bit like this to hang the belts so I
think this is the style of joint that I'll use for the belt hanging on top of the piece or on
top of the project and then these mortise and tenon joints will be used for the shelf to vertical
piece connection oh also this is the first one that I cut and I screwed up by making them all
the same size I forgot to offset them but I use this piece to test the round over and just a
basic round over bit that I already have works just fine and I think the round over will be
a little bit more durable long term to prevent any type of damage if something was to just
bump into the edge you see there I damaged this one but I didn't damage this one so that round
over I think is actually pretty functional here in Sketchup I already have the the stand and the
dust collector this isn't 100 perfect the dust collector isn't but it's close enough and I
downloaded this from the 3d warehouse I modeled this really quick not much to it just a bunch of
rectangles but I can use this to determine the exact sizes of all my pieces so I know my material
thickness is 0.763 and I just need model within the constraints of this particular
this particular model so I'm going to make the bottom shelf and I want this bottom shelf to
R for rectangle from this back corner to this front corner P for push pull and I'm going to
this up by the thickness of 0.763 inches enter everything has to be 0.763 inches
for the the model to be accurate I want this shelf to actually extend out by just a little
bit so I'm going to give it one inch and I'll put a little radius on there once we get into v-carve
now one thing that I do need to do is create a a big u shape to go around this and I haven't taken
those measurements yet but I'll do that right before I transfer everything to v-carve no need
to show that the front piece right here R for rectangle from this corner to this corner down
here P for push pull and I'll pull this out by the thickness of oops let me back up control z to back
up I forgot to make this a component so let's spacebar triple click G for component enter now
I can do this R for rectangle from here to here P for push pull and I'll pull it this direction
0.763 inches enter T for tape measure and I know that I have like a a 48 inch length inside the
belt so I want the bottom of the belt to be here which means the top needs to be about 48 inches
so I need to P for push pull and it's extended this top face to this line right there spacebar
let's grab that and press delete that's the basic gist of the structure now we need to add
the connections here so let's spacebar triple click G for component enter H for hide I no longer
need to see that and I'll double click to edit this part and I need to add some some box joints
here so let's go let's just go with R for rectangle and see just drag it in this direction and if I
snap to this bottom edge all I have to do is type in the first dimension which is the width here
let's do 1.5 enter let's do 2 enter and then 1.5 enter so now I have these three that I can hold
shift to select M for move control brings up copy and let's hold shift to constrain to the red axes
and drop it off over here P for push pull and let's pull this out by the thickness of 0.763
enter and double click to repeat my last push pull on these fingers let's click to get out of
our part U for unhide the front and now we have something we can trace so let's double click to
edit this front piece R for rectangle and let's just trace these I can grab this M for move control
brings up copy right there and grab both of these M for move control brings up copy from here to
there and now P for push pull I'm going to push this in the backwards direction stopping at the
thickness and I can double click double click and double click just to give it a little bit of
contrast so we can see the inner side so we can see these two pieces interacting with one another
I'm just going to throw some color on here and now you can see the mortise and tenon joints
for the shelf to the vertical piece now these connections I'm going to put a screw right in
the middle to connect to this piece so I will also have the screw itself acting against gravity to
stop this panel from falling down I think that should be plenty enough just those four mortise
and tenon joints and two screws now what's to stop this thing from falling in this direction
well we've got a connection there but I'd like to make some hooks that go around this and I can do
that in two ways I can do a mortise and tenon joint through here secure it with a screw and
then just make a hook that comes down or I can come from the side and make a hook that comes
around all of this stuff that'll reduce the amount of mechanical fasteners there's not that many in
so I'm just going to go ahead and do the mortise and tenon joint so let's go with camera parallel
and then go to a right view so now I know that I'm in a normal two orientation and we will go
with L for line come here and this is one and a quarter inch square tubing but I have some tabs
right here so in all honesty this is more like more like that I haven't taken that measurement
yet so I'm just going to assume that that's about a quarter of an inch quarter of an inch and I will
just add the extra back here now if this is too much of a gap right here I can shim it with tape
or something this is just the one off so it's not that not that important but this will all make
sense in just a minute so L4 line let's come this direction holding shift to constrain to the
right axis or you just press left on the keypad and let's go with it's one and a quarter inch
square tubing so let's go with 1.5 enter and then we'll go down making sure the blue axis is
selected and we will go down let's see it's one and a quarter like I said so let's go let's just
go with two inches and over by one inch just for some material mass and did that okay I was just
making sure that this didn't snap to the background here let's go back to this L4 line you know what
let's just go ahead and hide the cyclone we don't need to see the cyclone L4 line and let's go up
our initial two inches plus plus four inches let's go six just making this up as I go
hold shift to go over to here and then down to here so now I have a piece that I can p4 push
pull and go this direction by the thickness of 0.763 enter spacebar triple click g for
whoops spacebar triple click g not h for component enter m for move and I'm going to move this in to
the inside of this and then just give myself a little bit of leeway by going in 0.25 inches
now I need to add the mortise and tenon joint so let's go ahead and hide this front piece
double click to edit this part and r for rectangle let's go this direction by 1.5 enter
and grab this m for move control brings up copy what does that leave me in the middle that leaves
me one inch in the middle that's fine I'm gonna put a screw right through that so p4 push pull
and I'll pull this out by the thickness which is 0.763 enter and double click to edit to to copy
that I'm going to add roundovers and all that once I get to the cam software let's go with u for unhide
to bring this back and I need to put one over there before I add the mortises so let's actually
let's back up so it's still hidden and let's grab this m for move control brings up copy
I'm going to press the right arrow on the keyboard to constrain to red and I'll drop it off right at
the right where this this other member is and I'll push it back that same 0.25 inches enter
now I can unhide now I can double click the green piece r for rectangle and I'll draw my pieces here
m for move control brings up copy p4 push pull and I'll double click whoops wrong direction
ctrl z to back up let's push this direction constraining to this back edge and there we go
so that should work and and you know what here I think that there is there is room for a
measurement conflict let's just say that whatever this measurement is what do I have here
the space in between the space from here to here I have at 27 and 3 8ths let's just say
that it is 27 and 5 16ths it's just less than that well one of these two is going to hit and
not the other one so just to guarantee that all the weight will be on this bottom shelf
and not these up here I think I'm going to elevate these by a quarter of an inch and I'll still get
the mechanical connection here to prevent rotating forward so let's grab both of these
m for move and let's move them up by 0.25 inches enter and I can do the same thing with
these mortises let's double click to edit this part use a window to select all of them at once
m for move and let's move them up 0.25 enter so that looks like the structure
complete now I need some hangers for the top piece that's where I wanted to do those
kind of like a slip fit those slip connections slip joints so let's just go ahead and go back
to the right view and let's draw this l4 line from here to here let's go down
1.5 that sounds good come over one inch enter that sounds good and we're going to go up
let's see I'll just constrain to this and then an additional two inches and then we'll constrain
to this so now I'm at the front of the piece and I need to go an additional they're six inch wide
belts I'm going to go seven inches just in case they're not laying flat or whatever seven inches
enter we'll go down 1.5 enter we'll come over all the way to I'm going to add more and then just
start subtracting lines it'll make sense I'm just trying to use these snaps to measure from so I'm
all the way at this point let's go back by 1.5 let's go back by one and then from here let's go
down to let's see what is this measurement down to bottom right corner of the screen says that's
two let's go down three inches enter let's come over to here back up to here and there so I should
have if everything was done properly or if this was all traced out which I'm not sure if it was
or not there it goes so now I have this shape let's add a little bit of radius to it I don't
know if I should draw an arc here in SketchUp the reason I don't like putting arcs or anything with
a curve in SketchUp if I know I'm going to the VCarve or the CAM program is because all of your
circles and arcs in SketchUp are segments not true circles and sometimes that does translate
sometimes it does not translate to circles when you import it into VCarve so I'm not going to I'm
going to actually add a radius to this so it looks a little better I'll round over all of these
but that's the shape of the bracket p4 push pull we'll go this direction by 0.763 because I used
a bunch of segments to make these other lines I've got this other stuff to deal with and space
bar triple click G for component enter M for move and we're going to grab this press up to constrain
to the blue axis axis and drop it off right there so now let's let's come in you know what let's
start from the other side because I think I don't have enough room as it is and let's come in by
one inch enter and then from there M for move control brings up copy let's copy this all the
way to here move it over one inch enter now I want to divide these out and I can either put a little
line here there's two methods to do this first I could give myself an end point to snap to right
so then when I grab this M for move control brings up copy I can stop it on that end point and then
press like divide by six and then get even spacing but I never add these what I end up doing
let me back up what I end up doing is putting my start putting my finish and then just doing it
once more M for move control brings up copy put it right there and then press divided by six
that gives me one two three four five six seven I think I have eight so let's press divided by
seven now I have eight evenly spaced but because I copied one I've got a duplicate
over here so I'll just click and delete hopefully that made sense um what's the spacing in between
here two and some change so let's I'd like to do a probably more than what's necessary
actually you know what I can just add some over here the filter stack the filter stack is on this
side and it can be moved anywhere on this side if I have something vertically hanging it's going
to get in the way of the sander so on this side yeah let's just do that let's just add some more
space over here so let's grab this let's grab this corner right here this edge m4 move control
brings up copy and let's copy another one down 12 inches p4 push pull and let's pull this out
in this direction I don't know 10 inches eight inches we'll just do that just give us some more
space over here all I need is another hook up here that's fine the the filter stack is right
there so now let's redo this spacing let's move this over to here let's move it there by one inch
enter let's go top down so I can grab all of these and press delete let's grab the first one m for
move control brings up copy from here to there divided by I already did eight I already did seven
rather so I had eight that's divided by eight so I have nine nine should be more than enough
and that gives me some extra space in between up to three inches that sounds good I like that
so now I need to make the slots in the green piece let's double click to edit the part
and we're going to press k for hidden lines so you may or may not be able to kind of make this
out but you see the hidden lines of of where these two pieces intersect so I can press
r for rectangle and start right there and end right there and if I press y to hide everything
else that's I think that's a custom keyboard shortcut but as I'm editing a component I can
hide everything else so you see that rectangle that I just drew and I need to cut this away as
a slot for this to slide down from the top so I'm still editing the green part so if I click here
I'm actually selecting that face that I just made that rectangle not this white piece m for move
control brings up copy and I'll grab one right here and set it right there I press x nine enter
oh that's too many x eight enter and now I have all my my slots drawn out let me press y to hide
everything else once again p4 push pull double click control z I forgot I did some other stuff
so let's p4 push pull let's push it this way all the way through and now we can double click
to get rid of all of this other stuff press k to turn off my hidden lines press y to bring
back everything else and click to get out of the part so that's that's basically it kind of an odd
design definitely a one-off for this particular situation but this will give me something to
mount all of my belts to at the top there's no there's no screws or hardware necessary for these
connections they'll slide in from the top and gravity will keep them in place I will put one
screw in between these mortise and tenon joints for the hooks onto the the rack there the stand
and I will put one screw in between here I will take the measurements for this cyclone and then
just make a u-shape to delete this center section I'll do that off camera and then we'll I'll meet
you over in v-carve as you can see I added the horseshoe cutout or the u-shaped cutout around
the cyclone and there's one final thing that I forgot to do before we go to v-carve and that
is put everything on its own layer or now called tags I'm using sketchup pro 2021 and they've
changed I don't know what year they did this but they changed the layers to tags same thing
different names so what I want to do is only select all of the cnc components for me I've
already got everything else as a group so I'll just hide that select everything that I want to
have cnc cut and I will create a new tag or layer and I'll name it cnc with everything selected I
can go to add entity info and change it to the cnc layer or tag and that's it I just need to
save this file but what this what the layers or tags do is they allow you to import only those
only that specific layer or tag so I have other stuff in the model that's fine it's not going to
be imported so I'll go to file save as and as you can see I've already named it sandpaper rack I've
already saved this but I'm going to save this as a sketchup version 2017 my particular version of
v-carve pro requires 2017 or older files from sketchup to be imported so I'll save it as
sketchup version 2017 and I'll actually make notation in the file structure of su2017
press save and now I can go into v-carve pro so this is my file in v-carve pro a couple things
to note here I have a 10 foot long machine so the whole white area is 10 feet long and it's not
quite centered I have a vertical table up front so this red boundary is the sheet that I'm working
with let's turn off some stuff that's not needed I'll turn off the dogs and the plywood so this
red boundary box is the sheet of melamine that I'm working with now as far as all this stuff
that's already on here this stuff you already saw me cut out this is the testing that I did
this stuff you didn't see me cut out but this is stuff that I got distracted with and was playing
around with while making this video so while this doesn't pertain to this project I did cut some
stuff up on this sheet already and that's that's the result of that so disregard this but I need
to keep it here because well that space is already called for already taken care of already
designated it's already been cut out there's a couple different ways to import the sketchup file
you can go to your drawing tab and click on this import vectors button and just find the file but
I typically already have the folder open every time I'm working with this stuff so I just drag
and drop sketchup 2017 file and from here you get a couple different options the only two that I
really care about in this case is auto orient the largest face on top and then import only visible
data on the selected layers of cnc press ok and it imports I'll press hold shift and move with the
arrows and uh-oh looks like I won't be able to get it all on here is that real is that for real
did I goof up oh no I goofed up
all right that's what you get for getting distracted and cutting some other stuff
like I shouldn't have done so what's more important um I think getting everything on
this sheet is more important than having this space right here in front because the first
darn that sucks the first solution is to just break this horseshoe piece
into two side pieces and then that should fit no problem oh man oh well I guess that's what I get
one thing to note is if you see a solid line that's a group if you see a dotted line like
these are dotted lines that is not a group that's just a closed vector or a selected vector I should
say for modifying this I need to you for ungroup it actually I need to ungroup everything so I can
put uh fillets or radiuses in the corner so you for ungroup keep in mind that I did ungroup it
so if I go to move this one you know move this it's not going to move the the inside is going
to be independent now that they are ungrouped so don't accidentally move one and not all of it
I was just moving it back and forth with arrow key so I didn't change its position
I need to break this up there is a gadget called explode vectors so this is just one solid closed
vector all the way around but I can break it up into a bunch of different line segments so I'm
going to do that gadgets explode vectors and I'm going to delete this center section here
we're going to add a line from this end point right why is it not snapping to this end point
add a line from this end point there we go snapping to that end point and I'm gonna go a
little bit further just because it's easier to do that I gotta use the trim tool to trim this back
delete this other one over here now I have a bunch of independent vectors that I have to join
together so I'll select this press join it'll it says that the vectors after joining will be one
closed vector that's what I want so now I have a left or a right and I need a left so ctrl c for
copy ctrl v for paste and I'll just use the arrows to move it side by side the top and bottom sheet
of the melamine are the exact same so I don't necessarily need a left and a right but however
it's just easy to do with h to flip it horizontally now I have a left now I have a right
and now this should be able to fit basically anywhere yeah there we go basically anywhere
with no problem now there's kind of a rule in cad which is you don't draw what you can copy for the
majority of times it doesn't make sense to draw anything that you can copy copying is always
faster why do the work multiple times so I have a bunch of copies here as a matter of fact that's
five and five I've got one too many I think I only needed nine one two three four five six seven
eight nine yes so I have too many here I'll go ahead and delete one of these so never draw what
you can copy meaning I'm only going to modify one of these and one of these and then I'll copy
as necessary it doesn't make sense to modify all of them and then and yeah that's that let's do
first just the regular radiuses or regular fillets roundovers on the edges we'll change
we'll go with a normal fillet add this to let's just say we're going to go with 0.5 as the standard
radius for all of these the big panel all four corners here one two three four can be the 0.5
I want to add just a little bit more of a sweep here the front two corners on both of these shelves
those are 0.5 this is the holding bracket I'll put a 0.5 there and there and one up top that's fine
this is the the hanger for the actual sandpaper 0.5 0.5 0.5 I want to add a larger radius here
0.5 and 0.5 that sounds fine let's change this larger one to what does two inches look like
that looks fine one cool thing about this uh fillet tool is if you've already made a fillet
you don't have to go back in there and delete it and redraw the corner to do a different size
the icon you can see the cursor changes to an x and that cancels you can add cancel add
cancel as you change different sizes and that's just very very convenient uh let's add where we
two inches let's see what two inches looks like here that looks fine looks a little bit more
finished now I need all the dog bone fillets so there is a tool here gadget dog bone filter and
you can select all the kinds of stuff and it'll do all of your interior corners based upon your
specifications and dog bone then dog bone them all at once however I want to show you the slow way
just because there's not that many and I get them done pretty quick so you can go to fillet
dog bone fillet and change your tool radius to whatever the radius of the tool is I'm using a
quarter inch diameter bit which means the radius is 0.125 inches but I always do 0.13 just to give
a little space no need to be exact and the reason why you need a little bit of space here is because
this is a mortise and I'm using a round tool to create the mortise so I can't get crisp corners
crisp interior corners however the pieces that are going to go in them will have crisp corners
so what I need to do is add a little bit of leeway on a little bit of room for that sharp corner to
actually come into play so all this does is as the bit comes down it just goes in a 45 degree angle
basically to create a little bit of extra space on all of these interior corners it's called a
dog bone fillet and there's a couple different styles there's a t-bone fillet that doesn't go
on a 45 degree angle the t-bone goes to the side in either direction doesn't matter and that gives
you that same interior 90 degree corner I just prefer the look of dog bone fillets so that's
the route that I am going and again never draw what you can copy however there's not that many
of them here so I'll just go ahead and swing through this I also if I've got a few to do I
like to do them in rows and columns versus going around a single part just because it's less
direction change with the mouse so knock these out really quick and there's not much to do after this
piece because remember all the above pieces are going to be copied I need one two three per shelf
here and you kind of get a you kind of get a visual feel for this after you do it a couple times
this is the bracket hanger and these are the uh what the the sandpaper hangers so these need it
right there as well now again never draw what you can copy I don't know why I did it up here that's
the copy one so I'm going to delete this one grab this ctrl c ctrl v copy paste and we'll put it up
there now we have nine of these to do total so delete those copy paste and now I have two copy
paste now I have four copy paste now I have eight and we'll just get one more copy paste right there
so now I have my nine my two hangers I have all of my parts and they are done before I nest this
I want to make this into a group because I don't want this to move around independent of the
mortises that are inside it so I'll select all this g for group and now I can use the nesting
tool but I want to specify where the nest actually is I wouldn't really have to use the nest tool I
can bring this down here manually and it's pretty simple enough to get it done but it's cool to use
the nesting tool and I want to show you that so what I'm first going to do is create a boundary
for it to go into because I do have some other stuff to to be in the way so let's go with
something like this and say that this closed vector is my boundary box so I'll select this
first hold shift and then select this it's important to select the boundary box last
press the nesting tool and check this box that says last vector is nesting boundary
I've got a bunch of different options here the tool diameter the clearance in between parts I'm
going to change that to I've got plenty of room so just 0.5 border gap of one inch because I don't
want them to be right at the edge and auto orient the parts 45 degree angle sure whatever x and y
you can you can change all this stuff click preview and it'll automatically put put it on
there in a nice efficient way now this gives me a long strip what's going to be more beneficial
a long strip or a wider narrow strip I think a wider narrow strip so you can change x or y
press preview and I think I like this a little bit better it gives me a little bit more extra
space I guess I don't know in this case it doesn't matter we're splitting hairs here
so auto orient is done from the nested parts press okay now I need I want to do different
tool paths with this and with this so I'll u for ungroup it and I will I've already got some
vectors or some tool paths from this testing stuff that I've already done so what I can do
instead is just open this up and change what I want these are the pockets so I'm going to use a
tool path to remove all this stuff that way I don't have to worry about tabs and small pieces
flying around that's fine small stuff we'll get rid of those I'm using a one inch length of cut
bit and I have my cut depth set to whatever the z is plus 0.01 so I'm going to cut into the spoil
board by 0.01 and em25 pockets I always name my tool paths the tool and then what it is em250
means it's an end mill quarter inch pockets there we go nothing much to specify here oh
one thing to consider is I'm using a a compression bit that has a shallow up cut right at the bottom
of the of the bit itself sometimes if you don't specify whatever depth the passes are it will
automatically adjust them as necessary so let's let's uncheck this right here so now I have
evenly spaced it took all the entire depth and divided it by four based upon my maximum depth
per pass and that tells me that some of my pass depths are actually lower than the compression
so I won't get that compression effectiveness on my particular bit so what I want to do is
is maintain the exact tool pass depth so instead of distributing it by four it's going to give me
my specified quarter inch depth per pass and then the last one's a super tiny one that's fine I just
want to make sure that my first cut is lower than the height of my up cut in in the compression bit
that I'm using hopefully that makes sense so that's one thing to note here so those are my
pockets let's press calculate it'll give me an error saying I'm going to go to I'm going to go
a little bit further than the material thickness and that's fine I'm going to go into the spoil
board I know that let's press close I have my set to where it doesn't close that window automatically
by the way and now I can go to the perimeter which is this box that I was testing and I can select
different vectors we'll get all of this I'm holding shift to get all of this and I'm going on
the outside this is a profile tool path again z plus 0.01 for the cut depth same bit once again
I made sure my edit passes are set so that they maintain an exact tool pass depth of one quarter
of an inch I did add let's see I did add ramps excuse me ramps so it doesn't plunge and I am
going to add tabs and I'll simply just go to constant distance between tabs eight inches sure
that's probably too many but I have no complaints with that one thing that I do want to do is make
sure that none of these are down inside the small little areas of these notches here so
the number of tabs is fine and the majority of the placement is fine I just want to make
it sure that it's in a more convenient location to cut off with my method of cutting the tabs
which is a one of those oscillating multi-tools I think that's it so let's press close with the
tabs let's go to calculate it's telling me I'm going into the spoil board I know that
press okay and if I zoom in you can see the dotted line is the vector on the right side left side is
the bit travel which is correct in this orientation and then these green areas are the tabs I like to
make my tabs one eighth of an inch long and quarter inch tall that's basically for all
tabbing operations that I do and that's it I want to cut the pockets first and then the perimeter
without without stopping so I'm going to save this as save visible tool paths to one file
and I'll click save and load it up in mach 4 and then go ahead and cut it out looks like I goofed
up staging this shot to clone myself in so let me go ahead and draw a line and then I can delete the
background over there then I can put the actual cnc working underneath it so it shows up and now
we can begin so first off the estimated time to make these cuts on the computer was 16 minutes
and 21 seconds there's a value you can change or a multiplier that you can change to really dial that
in 16 minutes 21 seconds estimated the actual time to cut this was 15 minutes and 51 seconds
now that is at a non-optimized tooling setting I just used my standard setting but if you are
in a situation or if this was a manufacturing situation where time is money and you're trying
to just batch these out as much as possible there's many areas where this could be tweaked
first off is the feed rate for the pockets I don't know why but my tooling for the pockets was set
at 150 inches per minute and all of the profile cuts was set at 300 inches per minute I've really
pushed this machine to see what it can do and I'm confident at a full quarter inch depth of cut on
this material because there's not much resistance I can get away no problem I'm confident at 500
inches per minute now for the smaller sections where the pockets are the mortises you're not
really going to have as much time or as much distance travel to actually get to 500 inches
per minute so it may not make much sense or you may not see much improvement with smaller areas
like that but for all these profile cuts majority of the segments in these profile cuts you can see
quite a bit quite a bit of improvement by increasing that to 500 inches per minute so
I put those two values in and the estimated time went from 16 minutes 21 seconds down to 10 minutes
and 19 seconds you do the math to figure out what the actual would be and increasing it to 500 would
go from an actual 15 minutes 51 seconds to an actual 10 minutes even so five minutes savings
on that entire job if you're doing this over and over and over and over again you can see how that
can be very beneficial to speed up the process and that's just one of the a few different ways
like nesting that can increase or decrease the overall time of the cut next all of the pieces
can be cut free by cutting the tabs with an oscillating multi-tool then all of the tabs
are removed at a router table with a flush trim bit and finally most of the edges are eased with
a one-eighth of an inch round over bit as of right now I don't have any screws oh man I left something
up there I don't have any screws in this but it's held together quite tight with the joints
and I forgot to move the
filter stack so let me undo the bungee on the filter stack and try not to knock anything over
now what are we on okay we got to put the uh clips over the top spin this side in
and voila that worked out really good spacing right there is oh that's perfect that couldn't
have gotten any better that's luck all right let's put some screws in this thing
switching over to my cell phone to wrap this video up it's just a little easier to walk around
with this uh I am uh very very excited to get that done uh simple stuff like this right those
belts I've just been moving around and around and around for two years or so year and a half
and they've always been in my way and well it's about time I do something with a simple project
hopefully you enjoyed the engineering process or the design process uh for this solution and
hopefully you got something out of it I think that two shelves instead of one that wraps around is
is is still a big win in my book um mainly just wanted to stop putting stuff on here
get in the habit of not putting stuff on there mainly my spray bottle for water and then my
my bottle for sharp objects I'd rather fill this up and throw this away
with all the sharp stuff in it rather than putting screws nails and that type of stuff
in into the uh trash bin by itself just less opportunity for flat tires with that
anyway very clean install it's not secured at all it's not fastened at all to the
stand it's just held in place by gravity I think it's plenty strong enough to
to do the job as intended anyway thanks for watching you guys take care have a great day
I'll talk to you in the next video