A quick and easy build for my local high school. The cost of renting a lit up prom sign was $900! That's crazy! Instead of renting, I made a set of letters they can keep for less than $200 in material cost (150-ish for melamine and electrical + the lights they bought). I donated my labor cost to help out.
Each letter is made from 3/4" melamine and lit with a chopped-up string light kit that was provided to me. Each letter plugs into the next one so next year it can be used without the 22. Or a 3 can be made to add to it. ----------
my local high school is having prom this
year and one of the things that they
wanted to use for decoration is a light
up
prom sign that you can take photos in
front of so they looked into renting
them and was kind of shocked to find out
that it'll be 900 to rent well i'm going
to make a prom sign in this video and
i'm only charging materials cost i'm
kind of donating my labor uh to the
local community so it's a way for me to
give back a little bit and it's also a
way for them to get something that they
can physically keep and use year after
year if they want to so
the hardest part of this project is the
design work actually building it there's
there's nothing to building it's very
very basic but designing it was kind of
a time consuming process because uh once
we figured out the correct the height
for the letters i wanted to kind of get
as much height as we could on the width
of a sheet we settled for 46 inches in
height
but the problem or the time consuming
part was spacing out the lights so that
you have this balance or the symmetry
for everything and how far do you space
the lights well that depends on
the size of the bulbs uh we ended up
going with i'm not mistaking a seven
inch spacing on all this which
for these lights i think we could have
got i think i could have gotten a little
bit tighter spacing but i was also kind
of worried about using too many lights
and then not having enough sockets and
the string lights that was purchased so
a lot of little tweaks here and there
that was the most time consuming thing
but once the design was done we could
actually start on on cutting the
material melamine is the material of
choice for two very specific reasons
number one is the budget we're trying to
save as much money as possible and
comparatively speaking melamine is one
of the lesser expensive sheet goods
number two
assuming you're okay with the exposed
edges
then melamine is a great material to use
and the fact that it doesn't require
additional labor input like finishing
it's it's ready to go right after the
machining process so that's why we went
with melamine i do not have a vac table
vacuum table on this machine so if you
are interested in getting a cnc machine
and you think you're going towards the
production side of things you have to
consider a vacuum table i don't do
production work so it's okay for me to
not have to worry about that i just use
one screw per corner and for the most
part it works out quite well with just
screws as you'll see i made a boo-boo
down the road which we'll get to
but the first sheet was mainly letters a
few rectangles so it didn't take long to
cut it all and then of course there is a
little bit of uh tab cutting labor
involved yeah i don't have a vacuum
table like i said so i use tabs to hold
the pieces together as it's cut and then
i can use an oscillating tool to cut
those tabs and release the pieces right
off the machine the tabs have to be
removed and i use a flush trim bit for
this now i dedicated this
lever router lift that i made
for a flush trim station and i i do that
because of this right here it's it's
next to the table saw so i have a lot of
really wide material support so that for
example these letters i can very easily
cut all the tabs and not have to fumble
around with holding up this big sheet or
this big object uh you know up off in
space while i'm trying to flush trim
these tabs this extra work surface
really is a treat for flush trimming
station i had two boo-boos on the cnc
machine as my daughter would say boo
boos
mistakes mess-ups
first off i placed four rectangles that
were too close
and i ended up cutting through the tabs
cut through all the material support and
then of course the pieces shift
so that's that's a big mistake luckily
it was at the beginning relative
beginning of the program so i was able
to stop it change the vector move some
stuff around
and put them in some of the wasted space
and get them cut
so
the rest of the wasted space was just a
bunch of stars that we decided on using
to fill up the extra you know extra part
of the sheet and those will be used for
decoration
after cutting that
or restarting that i did have one more
rectangle that messed up and
unfortunately this was the very last
vector so i couldn't uh couldn't use any
more of that scrap to recut this because
i'd already used it to cut up all those
extra stars
for this particular piece it's an easy
fix though with some other scraps and
it's a rectangle so i could use the
table saw to to just cut it out really
easily out of the scraps one million
tabs that's what i have on my notes here
as i'm doing this narration it sure felt
like one million tabs each one of these
stars had i'm not mistaken i had it set
for a minimum of four tabs
and some of the bigger bigger stars had
six or eight tabs so
there's a lot of a lot of tab cutting
and then it's just rinse and repeat for
all the tabs at the router table on to
the assembly process now each letter
gets a box built on the bottom back side
and that box is what's used to kind of
counterbalance it and hold it vertical i
don't want these to fall obviously and
they're only three quarters of an inch
thick the the letters are so that's not
enough of an edge to uh to allow it to
stay vertical so each letter gets a box
and i wanted to
reduce confusion and the opportunity for
error so i laid out every one of the
letters all of the box components in the
orientation in which they will be
assembled so that way i can very easily
grab and cut the pocket holes in the
correct orientation now this particular
pocket hole machine is a low angle
pocket hole machine and the whole point
of a low angle pocket hole
is to to kind of make assembly a little
bit easier because it reduces shifting
especially when doing stuff like face
frames and such in this case
i'm not really seeing much of that
benefit because melamine is just so darn
slick so i still had to clamp all the
pieces together now most of the letters
are super easy to knock out in this way
you just just cut all the pocket holes
clamp it together
you know clamp the box structure
together and then secure it to the back
of the letter um goes by really quick
but the o
in prom the letter o it had to be
assembled vertically because there was
no flat spot on the bottom of the letter
there's no way i could just kind of
eyeball this on the table and make sure
that it is
it's going to be vertical so i set the
letters up side by side and sandwiched
the letter o in between two letters and
then installed the box
as is on the floor and that worked out
pretty well here's the first layout of
all the pieces stuck together and you
can get a better idea for the size of
the project at this point it's it's
quite long actually i wasn't expecting
it to be this long i had to get out my
wide angle lens so that i could fit it
all in the shot the easiest way to do
all the electrical with this is to get a
string light kit and cut it up as needed
and that's what i recommended that's
what they bought and brought to me
so when i first saw this my initial
thought was
oh goodness those those light bulbs are
pretty tiny i was picturing a little bit
bigger bulbs
but this ended up working out all right
now the size of the holes for the
sockets and the melamine i chose to go a
little bit on the large side that way i
didn't have to to fuss at all with these
sockets fitting if there's any variance
in the size of the sockets
and i didn't really have a plan on
attaching it so it's kind of a figure
out as i go thing
and what i figured out or what i decided
to do was
to put the socket through put the bulb
in place and then position the bulb
flush into the circle so push it down as
far as it can go that'll center the
socket in the hole and then i can secure
the socket with some hot melt glue on
the back side with the game plan in
place
uh string the lights all the way through
the letters cut everything as needed
install the bulbs which man that took
forever i'm putting all these bulbs in
here and i had to put them in and take
them out a couple different times and
then finally push the bulb back secure
the socket with some hot melt glue rinse
and repeat over and over and over
and over and here we are it's done and
i'm going to show you off and on of
course to show that it all works but
i kind of just skipped right through the
electrical it's kind of monotonous and
kind of boring but every one of these is
done the same way i'll go to the back
side
you'll see i have an extension cord
right here for power
every letter
has a male plug in the bottom right if
you're looking at the back bottom right
we'll have a male plug so i'll plug in
right here for power
power will go through all the lights
and then it terminates right here where
i spliced in
some more wire and a female plug
so in this orientation here that this
setup is just draped into some of the
stapled wire so that way
during storage this will plug into
itself and all the wires are kind of
contained and not dangling anywhere
because this female end is
a little bit long and it's left long on
purpose so that
it can go through
that hole down there
female plug will come through here into
the next letter
where this
this letter gets its power source plugs
in right there
again it goes through the same thing
through the whole letter
and this one i've already plugged it in
so i've got the female end the extra
can just be tucked down into these boxes
female end will come out of this hole
out of this into this hole
where it plugs into
this this male plug
i also added a little sticker
to the back
of every one of these boxes
now these boxes are here just because
this particular design i don't want to
fall forward so you can put a brick in
every one of these
and just as it is without any weight
they're pretty solid of course you don't
want to bump into them or anything
it's just kind of a photo op really
but let's let's plug them all in and see
what it looks like i haven't tested this
so hopefully don't have any
busted bulbs or anything
and i am five foot six these letters are
uh 46 inches tall so you kind of get a
size comparison
or an idea for the size
in that regard
p plugs into r
and then r
plugs into o
o
plugs into m which
did i already have them all plugged in i
do
all right so it looks like we have a
couple
dead bulbs
oh maybe they're not dead
all right
one thing that i do wish
i could have or would have done
differently is the boxes on the back
side
i wish i would have used something like
black melamine or something something
that wasn't white because if you're
looking at an angle
sometimes it depending on which way you
look especially on the p
the white box behind it kind of
looks like it's part of the letter and
it kind of goes to the back which it's
not supposed to be separate so there's
that uh this was a budget build tried to
reduce costs for our local high school
rather than renting them the rental
price for one of these setups not
exactly like this probably a little bit
better than this
was like nine hundred dollars to where
this instead
is something that they get to keep and
materials cost was a little less than
two hundred dollars
also
uh because these are kind of chained
together next year is obviously not the
year of 22. so we can either cut a three
and add it to it or simply disconnect
the two numbers and then you have this
that you can use every year going
forward
you