I recently completed a matching farm table base
and an outdoor kitchen sink island,
and I timed the build of these
so that I could spray them at the same time.
For the color, we chose Tuscan Red Milk Paint
by General Finishes, and the can itself provides
a lot of info on how it can be applied,
including instructions for spraying,
which is the route I'm taking.
So with a 1.8 millimeter tip installed in my HVLP system,
I can load the sprayer and get to work.
Here's a tip for pouring from a can.
Use a wide strip of tape to act as a spout.
Just cut a V-notch where you want to pour
and use an awl or a knife or a screwdriver,
something sharp, to poke a hole in the rim of the can.
Now, when you pour, the tape will act kind of like a spout
and drain the majority of the excess back into the can,
and the hole in the rim will allow you to,
it'll allow it to kind of drain back into the can
if you want to loosely place the lid back on.
The strainers I'm using make the pour process
a little bit long.
The strainers are a bit fine for this application.
In this case, it's okay because I'm trading my CNC labor
for some moving labor to help get these projects sprayed.
While the milk paint drips into the cup,
I started some of my CNC work.
Now, Zach and Jason are from Back 40 Customs
in Tupelo, Mississippi,
and they make a lot of epoxy river tables.
These walnut slabs will be for those tables,
but before the tables can be poured,
they like to lightly flatten the slabs
so that they will rest flat on the bottom of their forms.
After one slab, we're back outside to start spraying.
Now, first is the table base.
I found out quickly how well the coverage is
with this milk paint.
It's pretty darn good.
And I'm spraying outside with a slight breeze
on a rare low humidity day,
so the paint is drying super fast.
I could probably have gotten away
with spraying the second coat immediately after the first,
but because there is other work to be done,
I switched back to the shop to keep moving.
Another slab with the same goal.
Flatten without removing a lot of material,
and in this case, the SF-525 bit that I'm using
is it's just flying through the material,
so the rest of the cuts,
I gradually increased the aggressiveness.
Back outside for a second coat of Tuscan Red,
also making sure to really seal the bottom of the legs.
Now, I'll have leg levelers installed
so they'll never actually be sitting in water on the patio,
but I want to seal them just to be safe.
Slab number three gets flattened,
and by now I had a pretty good idea of how many passes
and how much material to remove.
This was the most aggressive cut
at 0.2 inches depth of cut.
One and a half inch step over and 500 inches per minute.
At this point, I'm maxing out the travel of the machine
and can only increase the depth per pass.
Another thing I noticed is how much harder epoxy is
on the surfacing bits.
It cuts the epoxy just fine,
but it cuts through this walnut
like a hot knife through butter.
It really is an impressive bit.
They also brought three smaller slabs
to be used as floating shelves,
which were small enough to be used on my jointer.
Now, this is a Hammer A341 jointer planer combo machine
with a 16 inch long cutter head.
Rarely does a job come up where I need the full width,
but when it does, it is incredibly satisfying.
Flattening with the jointer is always going to be faster
than flattening with the CNC.
The CNC obviously has a much greater capacity though.
After the first couple of boards,
a little extra push was indeed appreciated.
Now, of course, the guards were removed
for photographic clarity,
and you should never take the guards off your machine
just because you saw some doofus like me do it in a video.
Toy box front panels were up next.
These are just MDF paint grade projects
with a personalized front.
The first one said hood, the second one said toy box,
and we waited on the third for a spelling confirmation.
Four chunks of firewood were used to keep it off the grass,
and we rolled it upside down for spraying.
That way, just like the table base,
I could spray the bottom and get a better protection
from the ground moisture.
Now, of course, the leveling feet will be in contact
with the cement floor, not the actual wood.
A quick note about my dogs.
Yes, they do pop into frame here and there,
but know that my wife was outside keeping them back
while I was spraying.
More business as usual.
One coat for the initial coverage,
and then a second coat to ensure total coverage.
Now, overall, I am very pleased
with how well this product covers.
This is my first experience with General Finishes Milk Paint,
so I'm curious how well it holds up long-term.
I read that it does quite well outdoors,
so I'm looking forward to minimal, if any,
maintenance over the next few years.
Pretty productive day today.
I sprayed early enough to where the guys
were able to help me move these back into place.
The finish was already dry enough to move them,
so that was really cool.
I wanted to show you the trim that I added to the back
that I mentioned I would do off-camera,
but I never actually showed, so just the trim here.
Whoops.
Trim inside these panels to kind of give it
a little bit more visual depth, a little bit more interest,
and a little bit of work goes a long way in that regard.
So I like the way that turned out.
The table, of course, matches quite well.
I'm going to leave these here in the shop
for about a week while I go camping,
and then I have to source around 200 board feet of maple
or something similar for butcher block countertops.
So, again, the island is a little bit less
than four foot by eight foot.
It's gonna take up a lot of material.
This is eight feet by 40 inches, if I'm not mistaken,
the finished countertop size, or tabletop size.
So got a lot of repetition in store to wrap these up,
and then we get to install them.
That's it for this video.
You guys take care.
Have a great day.
Go to my website, jayscustomcreations.com slash newsletter,
and sign up for my email newsletter
so you don't miss anything that I publish.
I'll talk to you in the next video.