Bits&Bits is a supporter of JCC. If you're interested in high quality router bits at a competitive price consider checking them out. I am not an affiliate and gain nothing from their sales. Use the code JAYBATES for 10% off. Link to the SF525 - https://bitsbits.com/product/bitsbits-sf525-surfacing-router-bit/
The SF525 is a 2-1/2" diameter flattening bit that features two Astra-coated carbide inserts. I received this bit a few months before the product was launched for testing purposes. With this bit, I have been able to achieve the most aggressive feeds and speeds for slab flattening. I'm sure you can remove more material and be even more aggressive but these numbers are already as aggressive as I feel comfortable with on my machine.
I prefer to take multiple shallow passes vs a deeper, slower pass. The faster shallow passes allow me to sneak up on the "maximum allowable thickness" which is often the desired result of slab flattening. With this bit (and the original carbide inserts) I've flattened the included items in this video as well as three large epoxy/wood river tables with great results.
A price break is included when purchasing the bit, a pack of replacement carbide inserts, and a wrench with a replacement screw. However, you can purchase any of those three individually.
this is the bits and bits SF 525 it's a
half inch shank two and a half inch
diameter surfacing bit it features two
replaceable Astra coated carbide inserts
each with four cutting edges the Astra
coating reduces friction and heat
buildup which prolongs the life of The
Cutting Edge and it has a Max RPM of 14
500. also available is a replacement set
of carbide inserts the ability to rotate
and change carbide inserts on a bit like
this results in a much lower long-term
usage cost as the more you use it the
cheaper it gets today I'll be testing
the bit to see how it performs the
machine I'll be using is an avid CNC
with Nema 34 Motors and a 6.5 kilowatt
spindle however I'm powering the machine
on single phase 240 volt so the power
output is roughly 4.7 kilowatt testing
will start on a slab of Hickory I
frequently use a bit similar in profile
to this one so I have a good idea of
where to start the Baseline specs are an
RPM of 14 500 a 0.1 inch depth of cut 66
step over which is about 1.65 inches and
300 inches per minute of travel I want
to force a conventional cut with every
pass so I made a series of lines in
vcarve that are offset by the step over
distance of 1.65 inches I also want each
pass to be a different speed so I made a
separate tool path for each line
starting with a travel speed of 225
inches per minute and increasing by 15
inches per minute with each line to the
left this puts our Baseline speed of 300
inches per minute near the middle it
allows some conservative cuts to the
right and faster cuts to the left I let
the program run and to my surprise there
was no struggle to the cut whatsoever
each of the passes sounded the same and
I couldn't tell the difference between
any of them the final pass or the one
all the way to the left had a speed of
390 inches per minute but it did not
count as The Cutting path was mostly on
air which means the fastest full step
overpass or the 66 step over was at 375
inches per minute with no problems in an
effort to push the bit a little harder I
lowered the bit and started the program
over but this time with a feed rate
multiplier of 125 percent in Mach 4.
this will multiply the speed by 1.25 for
all of the cuts the same program is run
once again and just like before I cannot
visually or audibly hear the machine
struggle at all every pass sounded good
on this run the final full step over
pass was 390 inches per minute times the
multiplier of 1.25 for an actual travel
speed of
487.5 inches per minute that is
impressive the surface finish on the
Hickory was good enough to give a slight
low angle reflection but not good enough
to go straight to finish sanding is
definitely required when cutting at
these speeds which is expected here you
can see the depth per pass of 0.1 inch
some will argue that a more aggressive
cut can be taken by slowing down and
taking a deeper bite but that's not how
I prefer to use surfacing bits just like
a planer I prefer to take a shallow cut
to reduce the amount of stress released
into the slab or out of the slab I
should say I flatten a lot of large
table tops and the goal is almost always
to leave as much thickness as possible
I'd always prefer to take 2.1 inch
passes over a single 0.2 inch pass the
next test isn't really a stress test by
any means as I knew it wouldn't be a
challenge surfacing my MDF spoil board
at 500 inches per minute now we're
getting into the realm of the machine
being the limiting factor versus the bit
as my machine's cut speed is limited to
500 inches per minute one final test I
wanted to do was to see how it would
handle a delicate trim this is an end
grain cutting board with various species
of hardwood and it's held at the table
just with perimeter stops and gravity no
top down holding the goal here is to see
if the bit wants to grab or lift the
material like an upcut spiral bit and to
see if any burning results from a slower
speed and a more shallow cut for small
odd jobs like this I typically do not
run a program instead I set the jog rate
the depth and the spindle speed manually
in Mach 4 because these jobs are so
small it's basically faster to manually
jog the machine than it is to actually
create a program and then let it run
manually traversing from back to front
and left to right results in all
conventional Cuts this is a situation
where I wouldn't want to go really fast
because too much lateral force on the
cut May grab and try to pull the piece
up due to its lightweight and the lack
of top-down work holding no grabbing
here though it slices right through the
end grain fibers without any sign of
lifting and the combination of a solar
feed rate and shallow cut did not burn
at all here's my final thoughts I I
didn't go crazy with these tests but I
did prove a few things first I think the
limiting factor for my setup was the
machine X and Y travel speeds maxing out
at 500 inches per minute and not the
actual bit which sounds kind of crazy to
say the max speed I tested on the
Hickory was
487 inches per minute but with no visual
or audio indications of stress
I'm confident I could have flattened the
slab at 500 inches per minute
that's the top cutting speed of my
machine so I'm a little hesitant to keep
the machine maxed out for a full stress
cut like that again with with large Cuts
Like table tops and slabs I prefer to
cut no deeper than 0.1 inch per pass
cutting deeper will require the travel
speed to slow down but I prefer to cut a
little more shallow on large slabs and
tabletops to reduce the impact of stress
relief and also to prevent accidentally
removing more material than necessary
with all that said here are my
recommended feeds and speeds these are
the numbers that I saved in my vcarve
tool library and the starting point for
all of my surfacing Cuts if I'm cutting
something harder than Hickory which is
something like Osage orange not very
common at all or if the first pass in my
cut program is a full width pass and not
a 66 step overpass I'll likely bump the
multiplier and Mach 4 down to 75 percent
and adjust based upon Visual and audio
feedback if you are interested in
purchasing this you can do so at
bitsbits.com use my coupon code jbates
to save 10 at checkout that's a
non-affiliate code by the way it's just
the best savings that I can pass along
to all of you out there take care and
have a great day