Previously, my shop was always MY working space. This shop is a family shop and needs to accommodate all of us. This shop was purposefully built 2x the size of my last shop; it has to do twice as much. This is a working shop, warehouse, and living space.
The warehouse side is pretty much done. Pallet racking for vertical storage. And a pallet jack and forklift for bulk movement. Basic stuff.
Eventually, the living space, or apartment, will be a glorified "break room" with sleeping quarters for guests. Until then, we will live in the apartment until the house is built. Before the apartment can be built, the woodshop must be put together, so I can use it to help build it.
Before I finish setting up the woodshop, I need to work outside to get the shop's perimeter buttoned up. I need to bring in about 10 loads of material to finish building up the foundation perimeter on two sides. I plan on getting that started this week. Once compacted and potentially covered with limestone, I can move the camper out of the shop and hook it up behind it. The shop will partially shade the camper as the temperatures begin to climb outside and we begin work inside.
JK Boots Update 4/5/25: My O.T.s are still great. Heavily worn and holding up great. Still my go-to work boot. I recently got a pair of the square-toe western boots (The Buck - Indigo | Chocolate) for days where I prefer the speed of getting in and out of the boots, or days where I'm mostly on hard surfaces all day, or running errands. Very comfortable right out of the box with zero break-in for me. THUMBS UP AGAIN. https://www.jkboots.com/products/the-buck-navy-chocolate?bg_ref=BwlWA71DVt
That explains a lot, huh? Your arm is in
there. Get in there.
Please keep your hands and feet inside
the vehicle at all times. Thank you.
What do you mean? What do you mean? He
had his arm out. That's why he was
sitting up like that.
I need some storage bins so bad.
I know
it.
Heat. Heat.
You move that
truck.
You'll feel our slack and then it's
actually going on. Brakes are way at the
bottom. So that's literally it. This is
neutral. Down goes backwards. Forward
goes
forward. Forward reverse.
I'm going to glance and make sure that
these tires are straight cuz I need to
back up pretty darn
straight. All right, I'm going to very
carefully I'm not giving it any gas. I
haven't given it any gas this whole
time. Just back it off until it starts
to roll like you let off the brake of
the car and it's idling.
You'll feel it starting to go.
[Music]
Got
it.
Good. I want to just go high and all
this stuff so you have no room around.
[Music]
smidging
left. All
right, keep
going. All right, what you want to do is
go straight. So, I'm smidging right
straight. Right. Keep going. Keep going.
Keep going. Keep going. Keep going. Keep
going. Right there. All right. So, I
want you to go forward two feet and then
we're going to do a hard left. I want
you to clear that back side. Basically,
go
forward. Keep going. Keep going. Hard
left. Right there. All the way to the
left. Don't move. All the way to the
left. The buzz is back off. Right there.
Now, that off. All it's going to do is
twist. Twist me in the correct
orientation. Keep going. Keep going. Let
it go. Let it go. Let it go. Let it go.
Let it go. Let it go. And
stop. All the
way. Good.
You're going to tell me, but I can't
see. I got you. I got you.
[Music]
Now I want you to turn turn the wheel
the other direction. All the way. Yeah.
Keep going. Keep going. I can look at
the tires. Keep going. Keep going. All
the way. Your halfway
point. Keep going. Keep going. You're
good. Let go. Let go. Let go. All
right,
stop. Now turn to your
left. Basically, you want to go this way
and then do a hard turn right on hard
turn into your tool
cabin. Neutral kill it.
You have to add forklift operator to
your resume.
Who am I going to give it to? You can
you can put your resume in at Jay's
Custom Creations anytime.
[Music]
I got you. You're doing great. You're
doing great.
Okay.
I got it.
We are
done. I've been waiting so long to cut
open this wrap on the dust collection.
I'm okay.
[Music]
Heat.
[Music]
Heat. Heat. Heat.
[Music]
[Music]
Hey, hey, hey.
[Music]
Bye-bye.
[Music]
[Music]
[Music]
[Music]
Yeah, Tyler, we're not going to do
school today. I just don't feel it. I
need to, but I don't feel it.
We'll just catch up as we got this week.
I have more history for me tomorrow.
That might mean to test it.
Did you like test this when you were in
school? Tests. Tests. Yeah, you did. Oh,
no. I was saying yes to the way you said
that.
I like tested except it isn't tested. It
doesn't have that extra e in it. Yes. I
don't really care for math test,
but I like all of the other things. It
is many, many days later. And I I got to
be honest with you, this process right
here, setting up the shop, has been one
of the hardest things that I've done on
this entire property. It really has
because this shop is so much more than
any of my other shops. On this side of
the shop, this whole side of the shop
has to be a working space, a woodworking
space. On that whole side of the shop,
it has to be a warehouse where I can
conveniently access stuff for not only
the business, but for household stuff.
On that corner over there, it is
currently the living space in a
rectangle that goes this way, which will
eventually be a rectangle that goes that
way. uh the the whole apartment uh the
whole apartment layout and all that has
just evolved into all kinds of craziness
and what we find out is the original
plan seems to work the best. So, we're
reverting back to that. So, what about
all this stuff going on here in the
working space? Well, there's so many
hurdles that are coming to light and and
I want to set this space up so that
there's no deal breakers. every time
that I have put put it all in SketchUp
several times and there's three layouts
that work perfectly on SketchUp and then
I'll put it in place here and there's
there's one deal breaker that I just I'm
not going to do it. So anyway, it's it's
delayed me quite a bit which is okay
because I have no pressing need right
this second or in the immediate future
to really get back to woodworking. The
time will come. The time will come, but
it's not right now and that's okay.
There's a lot more pressing issues
outside. So, let
me let me
uh explain the method of this madness.
First off, the dust collection the dust
collection was on that back wall and it
went to the opposite wall. Still using
this first pllin as the main line, but
ultimately what the deal breaker was
there is I eventually want to get to a
point where the fine particles are
exhausted outside. I'll still have the
cyclone separation for the large stuff
so I'm not just making a a mess outside,
but ultimately the fine dust has to go
outside. There's no convenient way to
get the fine dust outside on that wall.
Plan B with that was to put it
underneath the lean to over here. Well,
that works and it'd be great to have
that outside under the leanto. Um,
however, that would require some type of
extra cost to get the outside exhaust
pipe from there through the, you know,
out the back and then also twist it in
such a way that it doesn't blow into any
anything right there. So, the solution
is why not just put it on that back
wall. I can use the filter stack for
right now. And when the time is right,
when I have everything set up, ready for
me to really make a nice outside
connection, all I have to do is twist
the motor on top and point it outside
basically. So, it's over
there. This has also been kind of not
frustrating. I I don't want to use the
word frustrating. Challenging.
challenging is a better word because one
of the deal breakers was setting up I I
did not want to dedicate permanent space
to a large CNC if that ends up not
happening. It's a big budget concern and
I'm still it's still a coin flip whether
or not I'll get another big CNC. I want
one, but it's a coin flip. I just want
to throw that out there. The plan with
that was originally to put it on this
wall over here. Right as you come in the
door, there'd be a long CNC right there.
And that's because I can bring materials
in through the door and just turn the
forklift and go right there. The problem
with that is I don't want to dedicate
that space to it and have a temporary
layout for the shop tools and then if
that doesn't happen then I have to redo
all the shop. I I just want to do this
once and be done with it. Right? So I'll
put an image on the screen that is the
final without question. It is going to
be laid out that particular way. And as
you can see, the dust collection is off
on a on its own in the corner. Has to
run, I guess, about 25 or so feet before
it hits the woodworking tools. But I
have the option, it's an option. It's
not baked in 100% where where everything
else is going to change if it falls
through. I have the option of if the CNC
happens, that's where it's going to go.
Straight direct path from the big door.
Um, everything, nothing is being
blocked. It took me way longer than
expected and also it took a lot of
putting stuff in place to realize
obstacles. Again, deal breakers was what
I was after. Find a deal breaker and
make sure that it's eliminated. Make
sure that that is addressed before
anything is set in stone. The tools are
finally where they're at and I'm going
to show you how much that all of this
truly does make sense. Made the lens a
little bit wider so you can see what's
going on. So once again, uh this is a
huge challenge because this is temporary
living space. This rectangle will
eventually be on that wall opening up
all kinds of other space. But dust
collection's always going to be tucked
away right there, right next to a door
to get it out. Also a clear path this
way to get it out. If wherever I want to
get the dust bin out, that's going to be
fine. Uh I I put a little uh a little
text on the screen earlier. I'm not
subject to any building code
restrictions, any any electrical
restrictions, any code restrictions at
all. I'm really not. So, I know that
that is kind of close, but it's also
plenty far enough
away that it's not in the way. I'm okay
with that. I know some of you out there
are probably screaming about that. Well,
keep screaming cuz I'm I'm okay. Uh
anyway, dust collection comes up. This
gives me a nice permanent location for
my office, which is actually awesome.
Um, there's going to be a wall here
about where this 2x4 is. And it comes
out, if I'm not mistaken, to uh the left
side of this window. So, right about
right about where I'm standing. This
will be a a pathway to get in and out.
This gives me a nice little office area
tucked away. I still have a window to
look out, which I absolutely love while
I'm working. And then it opens up into
the wood shop. So, dust collection has
started. And then I This is when I hit
the roadblock and I had to stop. This
will allow me to branch off to the left
if the CNC is a thing. And if it's not,
nothing changes. If the CNC is not a
thing, nothing changes. And that was
that's a huge deal. So dust collection
comes through. And I have my first uh
cluster of tools. This is the ripping
station. Now in keep in mind everything
one of these tools I wanted no deal
breakers. So I had to have good infeed
and out feed for absolutely everything.
back side of the table saw, I've got
like 15 feet of infeed. Great. Perfect.
On the front side here, I have eight and
I actually nine feet from the back side
of the blade to the front side of the
jointer. And that's only for wide stuff.
So, if I'm ripping a full sheet of
plywood, which I'll never do anymore,
but if everything's just, you know,
checking as many boxes as possible, if I
need to rip a full sheet of plywood,
nothing's going to stop it up there.
There's going to be my 4T by 8 ft table
right here. I love a 4T by 8 by 8T table
in the shop. It's going to be right
here. And that gives me some out feed.
I'll use this out feed table in the
meantime. But it'll give me a bunch of
outfeed to support that before it hits
anything like that. So, what about stuff
that's longer than 8 ft? Well,
everything's positioned perfectly. The
the blade is Where's the blade? Blade's
somewhere right here. And if I'm ripping
something long, that length goes in
between those two tools. And I don't see
ripping anything super wide that will
hit both of those tools. So this this
fits that. Also, the planer is further
that way uh to give me even more ripping
length. I measured this. I think it was
like 12 1/2 ft before it hit anything.
So that's great. Right here is my band
saw. This cluster right here, this
orientation table saw bandsaw is
absolutely perfect. I've done this many,
many times because at a band saw, you're
never using the lefth hand side. At a
table saw, you're never using this right
hand side over here. So, this is all
dead space. And once again, a band saw,
dead space left. I have it tucked in
here into the rails. This these are
52-in rails, and I can probably count on
my hand the number of times that I've
used 52 in of capacity. So, I actually
posted these on Facebook Marketplace.
I'll swap with anybody who's got 36 in
36 in rails. In the meantime, I'm just
tucking the bandsaw in. So, again, a
ripping station with plenty of in and
out. Go to this big bandsaw. That's my
ripping bandsaw. Ripping station, plenty
of in and out. This is my curve cutting
bandsaw. Curve. The biggest thing that
I'll ever do on a band saw is a big
circle tabletop. I don't know if I ever
I'll know if I'll ever do one
again, but here's the space for the big
circle tabletop. So, no deal breakers.
No deal breakers. No deal breakers. This
also gives me uh as much wall space as
possible. I only have two tools up
against the wall and I'll show you in a
second. So, this creates a nice little
cavity to start building shelves and and
a wall for storage like I did over
there. Um, this particular shop
construction because I'm not heating and
cooling it and I'm not worrying about a
tremendous amount of insulation. That's
basically all the insulation that I
wanted, which isn't much at all. Uh,
just to keep the temperature change when
the sun beats on it, right? Uh if if you
go outside underneath that in the dead
of summer, you might feel a little bit
of heat difference when the sun is on
this versus when a cloud passes cuz
there's nothing there and you can feel
the heat uh radiating down. So what this
little bit of insulation does is it
checks that box, but it also gives me
these cavities, these I'm calling them
closets to be honest with you to build
these out in various different ways. Um,
this sounds so simple, so so so
insignificant, but for me, I finally
have a little closet, a little cavity
tucked away for all my cameras and
tripods to be out of the way.
So, doggy number one and doggy number
two don't plow into them, which they
have been doing. Tucked away, stays
away, everything. H, I like it. It's
very basic right now, but I like
everything that's going on. Then we have
the router table uh with a essentially a
closet behind it to build out some
shelves or anything that's necessary. A
whole section here to build out anything
that's necessary. I really really really
like this. Got one of my cord reels
mounted and that's already just been
Man, you should have done that sooner.
The simple things in life, you know. Uh
the 4TX 8t assembly table here. These
rails on the table saw are 7 ft if I'm
not mistaken. And it's going to start at
the that side over there. So, it'll be
another foot this way. So, depending on
where I position the bandsaw, like
inches, we're talking about inches here.
I may or may not have some out feed um
out feed support by this big table at
this. Regardless, that big table is
staging for materials out on the band
saw and of course in and out at the
router table. So, this I've talked about
this in previous shops. I love a 4 foot
by eight foot table as a big assembly
table or a catch-all table or just a
general work table as the center spoke
of a workflow wheel, right? A center
spoke of a wheel uh of a center hub of a
wheel with spokes going all to the
different stations. This table will
serve the table saw. This table will
serve the band saw. It will serve the
router table. It'll also serve the
jointer and planer. So, um moving on to
this next area. There'll be a walkway
right here. And then the jointer. Let's
talk about the jointer. That's one of
the first tools in the um in the milling
sequence, right? One of the
first. So, if I'm bringing a bunch of
materials in and staging them on saw
horses right here, I can either go
immediately to the miter saw, which will
be on that wall I'll talk about in a
second, or to the the jointer right
here. Nothing's in the way. Again, this
table right here will help store
materials or stage materials for this
process. So, I have uh I believe uh 10
ft right now and it will be I'm sorry,
12 ft right now and it will be 10 ft
once that is uh built over there. The
miter saw station built up against that
wall. All of that works. Plenty of
infeed. Every bit of that works. This is
going to be a little tool island with
two tools, the jointer and the planer.
And um it's it's everything's wide open.
Even on the planer, I have plenty of
infeed and out feed. And I have two
material staging areas for this the big
table behind me. And then also my
workbench is going to live in between
these two. Now, this pallet stopping me
from tucking this in, but the arm on the
jointer fence, right? This has to extend
out quite a bit. So you think think
about this when you when you buy a
jointer, the back side of the machine
can't go up against the wall
because the whatever length of uh
capacity you have here, this fence has
to shift back for the most part further
than the back of the machine. So that's
an obstacle. This can't go right up
against one of those walls. It just
doesn't make sense. We're going to have
too much wasted space behind it.
Therefore, this gets tucked in right
behind these four rails. Once that
pallet's gone, this gets tucked in quite
a bit. And this overhanging the bed by a
few inches isn't going to matter because
this is higher than the maximum
capacity. This height difference is the
maximum capacity um of my of my planer
here. Now, well, that height difference
is going to change when I move this
pallet. Yes and no. Because I'm going to
build a little platform for this to sit
on. That way I can move this with the
pallet jack. If if whatever reason I
don't have I've got some major random
weird scenario where I need to joint
something super
long. I want to be able to just lift it
up with a pallet jack and move it say a
foot or two that way and set it back
down. That way I can do everything that
I need to do and put it back without
having to worry about dust collection or
electrical. So again, no deal breaker so
far. Everything is working perfectly.
There's going to be a little bit bigger
than this right here. Even if it was
this space, that'd still be fine. A
little bit bigger walkway this way. Then
there'll be a little bit bigger walkway
this way. So on this wall, we only have
the router table and my horizontal
sander,
which that's a useful tool. This gets
used so much more than what it's ever
been seen in my videos. This is one of
those jackof all trades and I use it all
the time. I'll never give up a
horizontal sand. This is I love this
thing. So, a sanding station and a
grinding station right here. This will
give me um somewhere up here to hang all
my belts. Perfect. Uh maybe even inside
that little closet. There you go. I do
have electrical on the left side of
every one of these windows and doors on
this wall that's not being blocked. It
visually is blocked, but you can still
plug things in no problem. No big deal
at all. Uh my workbench will be right
here, obviously. And on All right, so my
workbench real fast. This is my leg
vise. And if I put something in there
and try and handsaw, my elbow's in the
way. So, I can't handsaw at that vise.
But I can still put stuff up there and
plane. And of course, my um my vice over
here to clamp things on end to plane the
top. This is nothing is blocking this
side at all. If I need to do some type
of hand sawing, I can come to this side
and use this vice. And there's nothing
in my way this way for my hands sawing.
So again, no deal breakers. Uh the left
side of this sander has a an attachment
right here to be able to use this drum
right here. For the majority, I I've
used this several several times in the
past with bigger items, but you pretty
much I only pretty much use a quadrant
of this drum. And if if I need any
length, say I'm let's just say uh you
know a bow and arrow. Like if I'm that
particular shape. I'm not saying sanding
a bow, but that particular shape. You
got something really long with an inside
curve that you want to sand. The window
goes up and you can put stuff in and out
of the window. Super easy for those very
random scenarios. So no deal
breakers. Uh quick little grinding
station right by the door. Sanding and
grinding all right here. Also right next
to all my tools. This is just a very
handy setup. This little triangle here,
uh, sanding, grinding, working,
mechanics tools, and all my other tools
will go up over here. Very, very
convenient. Brings me to this wall. This
wall will be the miter saw station. And
I'm going to experiment with this wall.
This is kind of sort of a low priority
right now. I'll work this out in time,
but the miter saw is going to be
somewhere over here. And I'll have at
least 8 ft of stop block on this side.
and then roller stands on that side. So,
I can have great capacity without
dedicating a really long wall of no
windows. That was another roadblock for
me. I initially on SketchUp on paper it
makes sense to put the miter saw on this
wall at that biggest opening right
there. But it it kind of sort of doesn't
make sense because if it's a sliding
miter saw, it uh it has it it has to
stick out too far in this direction over
there and just it just doesn't make
sense. It can stick out quite a bit over
here and it doesn't matter. So, I'm not
sure how I want to do the storage over
here, but this wall is going to be
themed for storage as much as possible.
I don't know if that cart stays or what.
I don't know if I'm building all a bunch
of bunch of stuff. I I don't know yet.
But this wall will be the storage. And I
want to build some type of almost
passive dust collection for the miter
saw. Uh something that catches into a
big hood and falls down into a drawer.
and the drawer can be pulled out and
emptied. John Heis ibuild it.ca. One of
his his very first miter saw station uh
that he put on his website years and
years and years ago, we're talking
2012ish. Uh he he built a setup like
that and I built it actually in my first
apartment wood shop and it worked great.
It really did. So, I'm going to I want
to do something like that with maybe a
lowowered fan just to create a draft to
pull this stuff down and settle down
into a box and that fan will pull out
the the fine dust and just just keep
that draft going. This side will not be
hooked up to the big dust collector and
I'm okay with that. So, yeah, this whole
wall gives gives me space for the miter
saw. There's a clear path in front of it
for the for egress in and out as far as
getting materials in and out. And if I
spin around, everything that has the
longest in feed and out feed
requirements is in line with the longest
dimension of the shop. Perfect. No deal
breakers. Perfect. No deal breakers.
Perfect. Perfect. Perfect. Perfect.
Perfect. Perfect. Perfect. No deal
breakers. everything is set in stone and
it can finally be hooked up. Hopefully
that made sense. Um, again, I'll put put
the uh layout on the screen and there's
just nothing in the way. Everything has
perfect infeed and out feed. Everything
has long-term resilience as far as where
it'll be, how it'll be used. I don't see
any roadblocks. It's adaptive for the
future if the CNC becomes a thing. And
if not, nothing really changes at all.
Everything has finally found a home. I'm
going to get this space set up when the
time is necessary. Right now, a lot of
the necessary time is spent
[Music]
outside the ground.
[Music]
Alice, this must be
a battle rocks and sticks against my
chest. I'm
Alice. Dear queen of
hearts, I'mma grow you white
roses so you can learn to be kind.