Simple hack for lapstrake boat building - Building Gannet - Episode 9

Nomad Boatbuilding
98 followers
3 Video Views·Apr 14, 2025
My website: https://www.nomadboatbuilding.com
Instagram: https://www.instagram.com/nomadboatbuilding/
It's not about the money but living isn't free...
Here are some ways you can support this channel.
Get 5% off TotalBoat products here: https://www.totalboat.com/?sca_ref=3715732.xvvNNHFDPJ
Get 10% off Starbond Adhesives. Use the Coupon code NOMAD10
Shop here: https://starbond.com/discount/NOMAD10
Buy some merch: https://www.nomadboatbuilding.com/shop/
Support these videos with monthly or annual pledges at Patreon: https://www.patreon.com/nomadboatbuilding
Or make a one time donation: https://www.paypal.com/paypalme/nomadboatbuilding
welcome to Nomad Boat Building I'm Mark
Ruden and today I'm going to share with
you a little hack that I came up with
Boat building takes a lot of time and so
anytime we can find some place to save
some time it's well worth it Today on
building Ganet I'm going to show you how
to make buttons for lap strike planking
In lap strike planking one of the most
timeconsuming activities is clamping and
unclamping the plank that you're
creating in order to do the fitting
process You may hang and unhang a single
plank a dozen times or more to get that
fit just right And in doing so the
standard method is to use some sort of
clamps to hold that plank in place Well
using clamps to hold it in place is a
huge time suck Now I've got a simple
simple little hack that I figured out
for saving a lot of time during this
process This is so simple it might even
seem too stupid to do a video about it
but I'm going to share it with you
because I've never seen anybody else use
this little technique in their lap stake
building process This is something I
came up with on my own So let's jump
right into it So when we're lap strike
planking there's quite a few moments in
the process where we need to clamp our
planks in place often in the exact same
place that we had them a few moments
before Now there's a bunch of clamps
that we use for fastening planks at the
laps There's F-body clamps deep C clamps
there's cam clamps Brener clamps and
clinker pins So there's your Fbody clamp
there's your deep C clamp there's your
cam clamp there's your Brener clamp and
there's your clinker pin These are all
great clamps for clamping at the laps
but they're often quite bulky and they
can really get in the way of a lot of
the different processes that we use And
there's quite a few times where I don't
need the plank necessarily clamped at
the lap I just need it positioned on the
boat and held in place For that purpose
we use a a little shopmade jig called a
hutch A hutch is really just like a
clamp pad with a screw going through it
The point of the hutch is that it
spreads the load over a larger area So
you can screw through the face of a
plank and it and it prevents the screw
from bearing itself into the plank Now I
use a variation on a hutch that maybe is
more accurately called a button And
buttons are something we'd use for like
holding down floorboards in a boat So a
button at its simplest is just something
like
this And the purpose of this particular
style of button or hutch is that I can
fasten this to a stem or a mold and then
it catches the plank here in the notch
And so your hutch or button needs to
have a notch that is sized to fit your
planking We're using 38 planking on this
boat So I need a 3/8 deep notch Now the
length of this doesn't really matter but
normally it's twice the thickness of the
planking which is the size of our plank
laps And the purpose of this is to be
able to fasten the plank quickly and
simply without a lot of stuff getting in
your way And you can leave this screwed
onto the mold or onto the stem while
you're messing around with fitting the
planks That allows you to have the plank
butt up to the edge of this button and
locate the plank if you will Now quite
often it's nice to be able to get that
right out of the way It might be hard to
slide the plank into the button So for
that reason sometimes I will make them
like this with a little rounded inside
corner that allows me to pivot this out
of the way so the plank can drop onto
the mold and then the button pivots into
position and holds the plank in place So
today I'm just going to make a bunch of
buttons for this particular project
They're the kind of thing that I tend to
make them and then they just they
disappear after the project So I usually
end up making a fresh set each time You
can make it out of the planking scraps
quite nicely because that's already the
thickness of your plywood So you can
just use a bunch of that I haven't done
any cutting of my planking yet so I
don't have any of that scrap available
And I find I like hardwood ones quite
often because they're just a little
tougher Any piece of hardwood will do
for making our buttons Got a bit of
locust here This 3/4 in square Sometimes
it's better if it's a little bit wider
but that's fine So the first thing we'll
do is we'll draw a line down the center
approximately And that's for drilling
fasteners on And then we're going to
start putting in some division lines So
I'm just going to use my little miter
square here with a 3/4 inch wide
blade And I'm just going to step these
off for as many as I feel like I
need Each one of these will be either a
hole or a cut off Then on one side we
need a line that's the same depth as our
planking
38 So draw that line on
there And then if each one of these is a
fastening hole we need to offset that a
little bit So I'm going to offset it
by 38ighs of an
inch So that centers up my
holes And then we need a
hunch and a cut
off and a
hunch and a cut off and a
hunch and a cut off and so on Our hole
is going to pass right through And then
we're going to chop away the
waist and buck these into little pieces
So each of these will get a hole at
every second
marking And on the side each of these
will get a chunk cut out and the length
bucked off Now you could set up your
table saw for doing this but I just do
it on the bandsaw Fast and easy Doesn't
need to be fine furniture Over here at
the drill press we just need to drill a
hole in every other spacing that's large
enough for the average screw to pass
through Like 316 of an inch is about
right
Now we have to do a little rip and a
notch and then a cross cut for each one
of
these
Rip
notch cross cut
We just do all the notches first
Okay lastly we need to clean these up a
little bit While rounding these seems
like a hassle it is well worth your time
because the amount of time that you save
not having to remove these in order to
get the plank in and out is huge This
will only take a minute or two per
button And so compared to removing them
all the time makes a big
difference Just soften the saw cuts a
little bit
Now of course you could build these out
of two pieces of material say plywood
round over the ends of half of it glue
it together drill a hole through it but
I've tried it and there's no time
savings really in the end So I find it's
easier just to use solid stock and go at
it with the sanding stick like you see
me do
here There we go
That's all there is to it Buttons or
hutches A super useful thing to have on
hand And if you're lucky you won't lose
them between
builds I know that's a pretty darn
simple thing And yes probably not really
worth making a video about but the
reason I'm making a video about it is
because I've never read about it
anywhere I've never seen anybody else do
it And so for that reason I think it's
important that I put it out there It is
by far the most time-saving little hack
that I have come up with in lap strike
construction Now in the next video we're
going to dive right into the full
process of glued lap strike planking I
hope you join me again on building Ganet
here at Nomad Boat Building See you
later folks
