This Philco 41 602 Radio Phonograph Wants To Live!!!

Amateur Repair Time
257 followers
849 Video Views·Apr 6, 2025
We're trying to keep some of the vintage electronics out of the landfill. Many times when something stops working, it can be repaired if someone will simply take the time to attempt to repair it. This channel documents our amateur attempts at repairing vintage electronics we think are cool.
We don't typically restore anything, we're just trying to get them working again. We've found that most of this stuff was well built and with a little help will start doing what it was intended to do.
Radio Repair
Phonograph Repair
Clock Repair
Projector Repair
Ladies and gentlemen, welcome back to Amateur Repair Time. If you didn't see last week's video,
we've been working on this Philco 41-602 radio record player. And in the last video,
we did all of the caps, replaced a couple wires, kind of looked through a few things that were
suspect. And this was sent to me, it was actually given to me by a guy named, a gentleman named
Craig. And his father's name was Kermit. And Kermit kind of messed with electronics and went
to school for it. And whenever he passed away about 15 years ago, this radio was left behind.
And Craig was nice enough to offer it to me, if I could take it on. And so here we are.
So I've recapped it and we haven't put the new line on it yet, new power line on it.
But I think we're good with the caps. But I think the next thing I'm going to do is check the
tubes. This is a Philco, so it's got the Loctal stuff in it. The Shango Special. So,
usually, you know, there's nothing wrong with the tubes. But I think I'm going to check them first.
And then I'm going to, we're going to bring it up slow on a Variac, so we can watch it as
it comes up and see if there's any shorts or anything going on. And just see what we get.
So that's the plan, Stan. So let me get a tube tester out and we'll check these tubes. There's
only five. It's basically an All-American 5-esque set. It has a 7A, I'm not familiar with most of
these. A 7A8, a 7B7, a 7C6, a 35A5, and a 35Z3. So let me get out the tube tester and let's see
what's going on with those. All right, so first we have a 35A5, which is the output tube. Now,
I have found on the radios that I've messed with, at least, that usually the output tube is just
fine. That's pretty good, isn't it? All right, so our output tube is probably fine. Do I need to
test it two ways? Probably not. No, just one way. Okay. Well, that's good. I've got a whole ton of
tubes. I'm pretty sure I've got all of these, if any of them are bad. I shouldn't have said that,
because now I'm going to find... Well, we'll see. We'll see what happens. We'll see what happens.
Don't worry about it. We'll see what happens. All right, so next is the rectifier tube,
which is a 35Z3, which is very common. I've been organizing some of my tubes lately,
and I've got a ton of those. But, you know, the rectifiers are usually fine.
Yep, and this one's really fine. You know, you can't see the glow on these
Loctals, can you? You don't see much juice on the heater. Aren't the filaments slightly
different on the Loctals? I don't know if that's good or bad or what. Okay, so the rectifier is
good. Now let's get on to the 7s. Next up is the 7A8, which is the detector oscillator.
That's not good. That's kind of weak. All right, well, we'll have to think about
looking for another one of those. That's not great. Now we're on to the 7C6, which is one of the ones
that has three. So, first setup. Meh. That ain't great. I probably need to work on this tester.
I don't know that this tester is right. It hasn't been calibrated in 50 years.
Whenever I test them, I always get stuff like that. Now, you saw earlier
that the, of course, the rectifier goes all the way up because it's just a diode, but the
output tube always performs pretty well on them. I run into this all the time. Maybe this is just
how the radios are, but the front end of the radio, is that the front end? The antenna side
of the radio will be weak, but the output tube will be fine on this tester. And then usually
the radio works with the tubes like that. So, I don't know if that's just how they wear,
or if there's something wrong with this tester. I've got some other ones, but I don't know.
All right, so let's set it up for the second test on this. Got it set up for the second test.
Well, that's got a good swing to it. And finally, the third side of it. Also very nice.
Okay, what is that? It is the second detector, the AVC, and the first audio amp.
Okay, so I think, I wonder if that's the detector that I was testing first. Let's see.
So, 7AB was the one that was giving me crappy results. No, 7AH.
7A8. We got all of that. CBAA1. And so, now we are doing 7C6.
Got all this, and then CBAA1. Yeah, so see, this stuff is lined up the same.
And that's what tests weak. But whenever I move it to like, I'm doing like,
with it set like this, it tests nice and strong. So, I'll bet that's the detector part.
So, the detector oscillator tested weak, and then the detector, what I assume is the detector part
of this tube, tested weak. Okay, so. All right, so that leaves us with the IF tube. All right,
so last but not least, the IF tube. Oh, I wonder if it's got a short.
Not good. Yeah, you can hear it. It's making a noise, actually. Let me see if I can find another
one that we can try to just see if all of those are doing that, or if it's this particular tube.
Well, I had the tester set wrong. I had, this was supposed to be on E. I had it on F,
which is slide six. I don't know necessarily what that even relates to. It kind of looks like
that's the pin numbers, because on most of these that are the sevens,
they don't go past eight. And if you look at one of these circles,
they have eight pins. So, the setting is going to be, see how all of pin seven and eight are CBCBCBCBC,
almost for everything? I wonder if that's the filament setting.
No, it can't be. Okay, so C7, C6 there, how you do three different tests. Well,
the filament would be the same for everything. So, the filament could be pin one,
pin seven, or pin eight, because those all stay the same.
One, seven, and eight. And then some of these, it's slightly different, but I know, I think not
all of the sevens are Loctals. Some of them are just regular like miniatures and stuff, I think.
But it looks like almost all of them are pin one is set on A, pin seven is set on C,
pin eight is set on B. So, all of those are going to be seven volt.
Yeah, so that would be my guess. So, all that to say, I'm just trying to figure out what I screwed
up. So, pin six is the one that I, I mean, yeah, pin six is the one I had in the wrong spot.
All right, I can't completely tell. And then on the schematic, unfortunately,
1941, it doesn't give you the pin numbers on this part of the schematic. There may be another part
where they show you the pin connections. You can figure it out if you look up the pin out of the
tube and then figure out, okay, this is the anode, this is the cathode, this is the grid,
this is the heater. So, I don't know what I had wrong, but we'll see. So, I've got another one
here that tests, it's going to make it, I mean, I think it'll probably be okay. So, we'll pop that
in there to replace the one that I, I tested this one afterwards and it's real weak. So, I don't know
if I screwed it up or if it was just weak, but that one tests a little better. So, we'll put it in
there. Okay, so that, they all test, which is typical whenever I'm working on these old ones,
but I think we're ready to try to fire it up. So, we're going to try. So, I'm going to solder in a
power cord for it and we'll see if we can get it to do anything. All right. So, this is my little
setup that I like to use to check these. So, I've got a, what are they calling this thing?
A Veritran, also known as a Variac here. It's actually on, but it's at zero volts and we did
a video where we messed with that and checked all the voltage and everything and it's pretty
accurate actually. So, it has a fuse in it. I think it's a two amp fuse and it's plugged in
right now. So, this has power going in, but no power going out because we've got it on zero
and then it's going into this amp meter, which is down at zero right now. This thing is pretty
cool. It has a variable. You can change this to use different, the different meters. So,
for instance, that low gauge there is zero to one and then it's zero to five, no zero,
zero to two and a half and zero to five. So, there's three different meters, right? So, I've
got it set on zero to one. Now, these radios, they typically only go up to like 0.3 amp or something
like that. It's never, I don't think it's ever even half an amp. So, because of that, we're
going to be way down on the bottom of the scale, right? So, you're just going to see it move just
a little bit, but we're kind of on zero as we speak. So, the whole idea behind it and the radio
was plugged into that right now. So, the whole idea behind it is if there is a short, we'll give
it just a little bit of juice and you'll start seeing the amp meter peg because it's shorting
out. Some people do it with a dim bulb too. That's probably better, but I just don't like
messing with that. So, let's see. I'm just going to turn it on with no voltage and see if
we get anything at all. And I don't know which way you turn it to turn on the
radio or the phonograph. So, I've got it turned to the right and turned up, which I would assume
is the radio. I don't know, but I have it on zero volts. So, I'm just going to give
it a little bit of voltage and we'll watch and see what happens. That's 20 volts. I like what
we're seeing. Okay, that is up to 60 volts. Now, on other ones that I've done at 60 volts,
I have actually heard the radio work. This one, we have the bulb is lighting.
Now, we're not necessarily trying to reform any caps or anything. We changed all of them except
for like the Michael ones, but I just like doing it like this and seeing if anything crazy happens.
So far, nothing crazy is happening and we're using like no average. I can't,
on these tubes, I can't ever tell if they're glowing or not. These 7s and 14s, they just
don't light up all that great. I think it's because the filament is smaller or thinner or something
like that. Okay, so I've got it on 60 volts, which may not even be enough to make it work,
but let's see if we are hearing any static or anything. Nothing. All right, voltage may
still be too low or we may have a bad speaker or just whatever. It could be all kinds of stuff.
All right, so I'm gonna go ahead and turn it up some more. That's up to like 80 volts.
Is it rising? Just barely. All right, we're at 120 and you can see the indicator light.
So I'm wondering if we've got it on the phonograph.
You know, just for giggles, I'm gonna turn it back down
and then try it the other way. I mean, I don't think it would matter, but just in case it matters.
The reason I wouldn't think it's that is because you're turning it and the volume would be going
down up as you turn left. You wouldn't think they'd do the radio like that. You'd think if they were,
if it was doing both, that that weird way would be the record player. All right, so I've got it
turned that way. We'll do the same thing. Maybe a little quicker. Okay, that's at about 120.
Indicator light.
Nothing. We may have a bad speaker.
I'm not getting a peep out of it, folks. Socket problem, like usual. That's what
Shango's always complaining about. Shango knows. He's the man. I have no idea how this works,
and I don't have the antenna hooked up.
Yeah, so the radio is the traditional volume. Here in Charlotte, we have a station 1110
AM, of course. 1110, that is a clear channel station. So at night, it's just crazy strong.
And I suppose these are the antenna leads.
So I think that was our 1110. That should, you know, it should probably be about right there.
I guess you go by those little dots, huh? Hmm, if you do go by those dots, you know,
1110 would be halfway. Oh, she sounds horrible. The speaker has a crack in it, though.
Boy, she sounds bad. Let's wiggle some tubes, see if she sounds better.
Please don't electrocute me, little radio.
Huh. She's working. She ain't working that great, but she's working.
With no antenna. Okay, so the sound, you know, I had that going on. It was just the antenna. So
I, it's supposed to have that loop antenna. So I thought, well, what a, I guess that,
you know, technically it should be connected then, you know. So I just connected it together.
So it sounds good, actually. When we hook it up to the antenna, we should be good.
So it has like, it has a pretty clean sound. It actually sounds pretty good.
There is a, like a filter hum or whatever in it, like a line noise, which is probably because
we don't have this in. But we're going to leave it like that for now. Okay, so it's working. It's
just not getting very good reception. So I guess next up would be, we need to align it. Now,
you're supposed to align it with the antenna hooked up, but the antenna is attached inside
of the phonograph. So, maybe I can rig it up. Maybe I can just set this on top and run the
wires down behind it or something. All right. Well, the problem is that, that loop antenna
is damaged. It's that kind that's almost like a tape. And I don't know what the hell the problem
is, but if you, if you remove these, I've got them soldered back on there, but if you met,
if you test from here to there, it's not connected. So there's a break in it somewhere.
Everything looks pretty good. So I would assume it's right here at the beginning.
And what it comes down to is with it hooked up, it doesn't work. Like it's just,
it's back to how it was. I am getting one other channel,
just barely. And if you go back up to our strong channel,
you've got the auto tune on it again. I mean, I shouldn't say that you might not know what I'm
saying. You've got the robotic voice on again. So that antenna is just not going to work. So I'm
going to have to remove that or maybe remove this end of it and look behind there. Perhaps
it's broke right there. There's also a couple of staples that they've put in it. I wonder if they
broke one of the lines with the freaking staple. Surely that wasn't supposed to be stapled like
that originally. There's nails here, but I think it misses the actual, it misses the actual antenna.
It's in the, it's just in the paper. Yeah. So there's the antenna. You see the nail is out of
it, but I think they may have broken the wire somewhere in it. So I'm going to slowly peel
some of that off and see if I can find the break. And if I can get that reattached, I think it'll
probably help our reception. If not, I guess I could make one, which I'd rather not do because
that's probably a hell of a lot of work, but we might have to do it. I should be able to find where
I got you sucker. Uh-huh. Uh-huh. I've seen it a thousand freaking times. Wire broke.
They ran a staple through it.
All right. So it's kind of hard to see it, but I soldered it back together,
stripped the ends a little bit, soldered it back together. And then there was another one too,
and I soldered it back together. And now I have three ohms resistance between this leg
and that leg. So I'm going to clean this up and lay it back down as flat as I can
and not put staples in it. I think I'm going to gorilla glue the crap out of it
so that it all stays together where the, because this has came loose, you know, from the
strapping. If you watched the first video I did on this, you know that I was already like that, but
so I knew we were going to have to repair this. I didn't know that I'd be able to save it, but
I think I just did. So I'm going to lay it back down as flat and as nice as I can.
And then we'll put the wires back on it so we can do the alignment and stuff. But
ultimately I'm just going to glob a bunch of like gorilla glue on it to hold this where it won't
move. Okay. That's a weird thing for you to come back on. So I've still got it on 1110. I was able
to repair it. I got most of it tucked away. Again, I'm going to put like a huge glob of glue to fix
this over here. But I've got the two wires back on it and it's connected. And so it cleaned up
the signal. The base and treble switch also works.
Okay. So let's see if we get better reception. I've got it. It's kind of how the antenna,
the distance the antenna will be from it, but it will be reversed. So I don't know, you know.
Oh, that's the volume. Duh.
Okay. So we are getting other channels. Oh yeah. So much better. Definitely needs a line.
I wonder if that's our lights. I've never had the lights interfere with anything.
People always say, oh, it's your lights. I've turned off everything in the house,
but I've never had it really help. So that's alignment, I think. Okay.
All right. So I think the next thing I'll do is try to align it a little bit. I found
another document that kind of showed some of that. So let me go check it out.
All right. So I've got the signal generator out. I've been working through it. So this is the
paperwork I was talking about. This is from the yearbook. They called it the Philco yearbook.
And so each year, apparently Philco put out an entire selection of their stuff. There is a really
cool Philco website that just covers all this stuff. If you just Google any of the model
numbers, you'll find that Philco radio website. And this is just, this is actually the stuff from
Philco. So it's showing you everything that they have about it. They even have a part list.
So anyway, I'm doing the alignment. I already did the first part, the RF. No, the IF. I've already
done the IF. Set the, at the 455. You put the receiver on 540. It keeps telling me range switch
broadcast. I don't know how you change that unless it's when this goes back. I don't know.
I don't know how you change it from broadcast to meters. It's on broadcast obviously.
So it says a new type dual volume control and on-off switch combined in one unit
is used to control the sound output of the radio and phonograph.
But it doesn't, it doesn't say anything about a switch. So I don't know. So anyway, we are on the
second one here, which is you turn the dial setting to 1600 on the signal generator and you put the
receiver on 1600. I think this one is a little high whenever I checked it before. Like if I put
it on 450, I'm actually at about 455, which is where you want to be. So 1600, it may be a little
higher than 1600, but we're rolling with it. You got to turn the volume up and you can hear our
signal there. I kind of want to turn it down to where I can barely hear it. And this is our
That right there is the signal generator. Let me bump it up some more. There it is.
Oh, I've got a kind of crappy connection on the wire. Now you're really supposed to do it
with a meter, but I'd like to be able to do it by ear. I think that's it there.
Well, I got it aligned as best I could. It's still got the same issue though. I run into
this all the time. The bottom part of the dial just isn't there. And I've heard, I've seen other
people complaining about that online on stuff. I don't understand. I don't really get how you fix
that. So we're coming up on our really strong channel. I'm going to turn it down a little bit.
Maybe not that far down.
Wednesday through Sunday, George, 10 to 5. And we welcome anyone that has an interest. As always,
one of us, we have an incredible volunteer staff.
So if big portions of this part of the video are missing, it's because
YouTube cut out the music.
That ain't bad, is it? What do you think about 1510?
Oh, you definitely get knocked off YouTube for that one.
How long do you have to be deceased before people can play your music?
Let's go back the other way.
The escalation.
So I hear the noise.
Every time I mention that people go, oh, it's a switching power supply in your house.
I don't know. I've turned off everything in the house.
All the lights. I mean, they're on right now, obviously, but I've chased this like 10 times.
All the lights, everything. So then people told me, oh, it's the neighbor's lights. Well, you know,
I'm going to throw the bullshit flag on that. I don't believe that.
Because I've got some radios that don't do it. So I don't think it's the neighbor's lights.
I just don't believe that. It could be true. If it is, I'm just wrong.
Okay. So it may get better if I reposition the antenna. Like if this was facing the other way,
it might be better or whatever. But I think we've pretty well got the radio working. I mean,
I don't get them working too much better than this to start or to end with.
The 7A8 was questionable. I wonder if, I mean, you'd probably have to realign it if you swapped
that. But I wonder, I thought I looked everywhere, but let me make sure I don't
have another 7A8 we can try it just for giggles. I'll go down to my neighborhood hardware store
here. Check out their tube tester. You know, you open this drawer and you've got them all in here.
Let's see here. 7AF, 7Q7, 7X7, 7S7. I think they're going to need to restock pretty soon.
Getting kind of low. OZ4. No, that's not it. I need 7V7, 7W7. Well, hell, there's a 7A8 right
there. Hey, how much is this tongue saw? $7? $3? Okay. All right. So I swapped in a new old stock
one and it does sound like I'm getting one more channel there now. That's better, isn't it?
And it goes completely quiet at like 80, 800.
Wow. Remember this is a 1941.
I'll tell you another thing I don't understand about these.
That light never lights up the dial. What is the purpose of the dial indicator light
when it never lights up the dial? Like it always looks like this. There's a really bright spot
and you can't see any of the dial. I've fixed like six of them and they're all like that.
I'm wondering if there's something missing. Like maybe there's some kind of reflector missing
that reflected it down over the dial or something, or maybe it was painted white
so it reflects like that. I don't know.
That's pretty cool. I like that. All right, folks. So we got that done.
I think it's working pretty good.
I think we're definitely getting better reception with that new tube.
Okay. So yeah, I think at this point it's an antenna issue, but I don't know. So leave your
comments below and let me know what you think. I'm going to do another video where we work on
the cabinet. We work on the phonograph. So we'll do that next time. But first video,
we checked it out, looked at some of the other stuff that Craig sent.
We took it all apart and recapped it. This video, we checked the tubes, aligned it,
brought it back up. Next video, we'll work on the cabinet, getting it a little nicer and
see if we can make the thing look presentable, get this mounted back in there
and work on the phonograph a little bit. Oh, you may have not even seen the cabinet in this one.
Let me show you the other side. So this is what we're working with.
And here's, it's got lots of issues with the veneer or the ply, I guess.
And of course the phonograph needs completely rebuilt. Yay. I've got the platter
and it's got the old, really old crystal cartridge.
With a nail. So we'll get into that next time. Leave your comments below.
Let us know what you think and we will see you on the next one. Now,
if you want to see another radio that I rebuilt a while back, I did an entire
series on this beautiful little Silvertone here. I was able to get it going, redid the whole thing,
sounded pretty good. And I was able to send a video to the gentleman that owned it. His
grandfather owned it and he was very happy about that. So if you didn't see that video,
we'll put up the playlist for that right here. So you don't have to do without, but we'll see
you back here in a week where we'll work on the cabinet of this one, this Philco. Have a good evening.
