In this video, I show the most common cause of why an Electric guitar would stop making sound, how to diagnose, and how to fix that issue.
When a guitar has been played for a long time and has been subject to wear and tear over the years, its very common for a wire on one of the control knobs or the audio jack to come loose from its Solder Joint.
This can be fixed with a soldering iron and a screwdriver, and only takes around 15 minutes of work!
If you have a more serious issue than this, it may be time to consult a professional and take it in to a guitar shop!
Thanks for watching, don't forget to leave a like and subscribe to the channel for tons more great content!
foreign
what's up you guys welcome back to the
Master Tech and in today's video we're
going to do something a little different
and I'm going to show you how to fix
your guitar not making any sound while
it's plugged in
so this type of video is obviously a
little out of place for my channel but
it honestly just sort of happened to me
this week and so I thought that would
make some pretty good content it's a
fairly engineeringy concept and it could
save a lot of musicians a lot of money
on taking their electric guitar into a
repair store when it's actually a pretty
simple fix that you can do with just a
few basic tools okay so nine out of ten
times that you're having the issue that
your guitar that was just working the
other week stops making sound it's an
issue with wires that are behind this
panel and so most guitars are actually
fairly standard here you can access
these wires just by undoing a few screws
obviously this is a fender Jaguar most
fenders have the same little three screw
mechanism I know there's some acoustic
semi-hollow guitars and other brands of
guitars where it might be a little more
complicated than that but most guitars
have a way for you to access the
electronics below the volume knob and
typically you want to find whatever
panel is closest to your volume knob and
your actual input Port okay so let's go
ahead and open this up and take a look
at the wires underneath here so we
understand what's going wrong what we're
going to look at first is what's going
on on the underside of our Jack because
that's what actually takes sound in from
the guitar and moves it to the amp so if
yours looks kind of like mine then the
problem is probably going to be pretty
apparent you'll probably have a bad
solder where these wires are either
loose or they'll lift right off okay so
I know looking at the underside of this
can look like a lot of electrical
engineering scariness at first but it's
really not the things we need to focus
on here are just the two wires that are
attached to the Jack nine times out of
ten if your guitar has completely
stopped making any sound it's not just
fuzzy or distorted one of these two is
going to have a bad solder connection or
it will have cracked or broken off of
the lead entirely for mine one of them
was originally off on its own and the
other one was actually pretty loose so I
just took them both off because for the
purposes of this video I'm going to want
to fix both of their solder joint
connections if you have a bad solder
joint on any of your knobs anywhere in
this circuit you can get this same kind
of issue so what we're doing is
specifically for the audio jack but if
you have a bad solder joint anywhere
along this line you can fix it but if
you have a damaged electrical component
and you're not comfortable with like
electronic engineering then you probably
should take it into a repair shop but
I'm going to show you what to do if you
have a simple bad solder joint like I
have here so let's discuss this while
the solder gun is heating up but
basically what we're going to do is
we're going to take the hot tip of our
solder gun and a little bit of our
actual electrical solder and we're we're
going to try to melt a bit of solder
onto the join point for the wire and the
metal lead that it's supposed to be on
so what can make this a lot easier is if
you have like an alligator clip or
something that can kind of hold your
wire in place or you might want to try
to I know it's going to be hard to see
with the camera but you could try to
bend a little hook into your wire so
that it'll stay in place a lot better
while we melt solder onto it because
getting a good contact right here is the
most important thing to make sure that
this joint takes and that it lasts
because you don't want this to happen
again in a few weeks alright so let's go
ahead and take a look at how to actually
solder these together go ahead and get
your solder pen
and try to get your wires to sort of sit
there again if you have gator clips that
can work but you basically need it
stationary so that with one hand you can
feed solder and with the other you can
melt it with your pen so take a little
bit of solder and your pen and melt it
and you're gonna have to remove the pen
for the melted solder to set up but once
you do remove your pen it does dry very
quickly and so I like to call it the tug
test but just within a few seconds of
you finishing the solder give it a
little tug if it pops right off like
that you didn't take well to one of the
leads so if you don't pass the tug test
you just have to get your lead back in
place re-melt that solder and you need
to get it to where it really has a good
grip not just on your wire but also on
the lead you're attaching it to you
should have a very snug connection that
passes the tug test put it back in
make sure you get all the wires tucked
away
and screw it back on and then plug it
back into the amp and see if you've got
it playing okay so the test is obviously
plug your guitar back in turn your amp
back on
and you should get a pretty clear
[Music]
you should get a pretty clear sound if
you're still getting a lot of fuzz or
you play and it kind of
Cuts in and out then you might have a
bad solder joint that probably means
that you need to get back in there and
make sure that those have a really good
connection this is a silly thing to
check but when you plug it back in make
sure your volume knob is not all the way
down because you can initially think oh
crap it's still not working but there's
a chance your volume knob might just be
down
and it should be pretty clear for you so
if you did the soldering if you open it
back up and you try again and you're
confident that all your solder
connections are still good then it's
probably time to go to the guitar store
and then you're probably at the point
where you need to replace a capacitor or
something along those lines so at that
point it's a little past standard home
repair and it is probably time to go to
the guitar store okay and that is going
to be pretty much it guys thank you so
much for watching I hope that helped if
you have questions about what you saw in
this video or want to let me know what
you'd like to see more of on the channel
going forward feel free to let me know
about in the comments below I appreciate
all the views all the subscribers
consider leaving a like on the video
subscribe to the channel it helps me out
a ton and consider checking out my
patreon link in the description of the
video as well if you want to become a
super subscriber of the channel thank
you so much for watching until next time
thanks bye