DR #22 - Carver M-1.0t Power Amplifier Troubleshooting and Repair - No Power

Duality Repair
132 followers
3 Video Views·Mar 12, 2025
In this video, I document the troubleshooting and repair of a Carver M-1.0t power amplifier with no power. I miss the target a few times but ultimately find the issue and get this amp working again.
hi everyone welcome to duality repair
this is my first Carver amp for repair
this is the em-dash 1.0 t it's in great
shape cosmetically but it will not power
on I've already pulled the fuse and
discovered that is indeed blown this is
a 10 amp fuse so we know there was a lot
of current being drawn through there at
one point so it's definitely gonna need
some work my plan for this amp is to
attempt to repair it first and if I can
I will also change any necessary
components to make it perform optimally
first step is to remove the cover take a
look around and perform a visual
inspection here's the inside of the unit
and this thing is very very clean I'm
very happy about that
that plus the fact that it's got a
service panel on the bottom means that
this thing will be a dream to work on so
I've looked around the board I don't see
any signs of thermal damage I've
inspected the drive transistors both on
the left and the right bank and all of
them look to be in good physical shape
there's no cracks all of the
electrolytic slick to be in good shape
as well they're not bulged they're not
leaking so physically visually
everything looks to be in good shape
it's possible that somebody just over
drove this amp and blew the fuse we
could replace the fuse and turn it on
and it'll work just fine the first thing
we'll want to do is go over the block
diagram as well as the schematic take a
look at how this thing runs specifically
the power supply section to see where we
want to focus our attention before we
look at the block diagram in the
schematic I thought I would attempt to
rule out the power supply right now so
the service manual does a great job of
identifying the power supply voltages as
well as their test points and so I
thought I would test for those right now
so of course to do this we have to power
the unit on I've already replaced the
fuse I only have a seven amp fuse but
that should be just fine as I'm not
going to apply a load to this I plugged
it in and turned it on and I can hear
the transformer hum but it would not
pass a signal so will not short and blow
the fuse but it also does not pass a
signal so we can test it right now so if
we look at the calibration procedure of
the service manual step one is to look
at the high-voltage points so there's
plus and
one hundred volts and those are going to
be at test points five and six so test
point five is hidden from view under
this wire but it's right here
test point six is also hidden but right
here so those will be easy to check next
our positive sixty one and thirty volts
and negative 30 and 60 volts those are
going to be at D 126 128 130 and 132 and
those diodes are right here all in a row
also very easy easily accessible and the
last two voltages are going to be plus
and minus 12 volts this is the inverting
version so I'm going to be looking at IC
301 pins 11 and 4 for those voltages so
let's go ahead and plug it in turn it on
and check for these voltages all right
so let's plugged in I'll turn it on you
won't be able to hear anything have my
meter on and we'll start probing so
again I will start with the high voltage
so we're gonna look at test point 5 for
positive 100 volts test point 5 is here
do that 3 volts I think that's a problem
let's look for the - 100 volts at test
point 6 - 3 volts a little bit of a
problem let's check the other voltages D
126 the anode should have positive 61
let's see what that's that nothing D 128
anode should have positive 30 volts half
a volt D 1 30 cathode should have - 30
volts - half a volt and D 1 32 cathode
should have - 60 volts nothing obvious
problems already so let's look at the
last two voltages IC 301 pin 11 should
have - 12 volts and we have nothing
millivolts and IC 301 pin 8 should have
positive 12 volts alright so we have
nothing on almost every test point
except for the hundred volts we have
just a small amount of voltage there's
something there three point three and
negative three point three otherwise
everything else is nearly zero so we
definitely have a problem so now we can
go over the block diagram and the
schematic of the power supply section
try and identify some key sections that
we want to test here's the block diagram
for the unit let's take a look at the
power supply section so we have our line
cord coming in on the left it enters the
fuse on the non-inverting units as a
noise filter goes through the thermal
protection and it enters AC power
control AC power control is going to
drive the primary of the magnetic field
coil or the transformer secondary is
going to supply three different taps one
for high voltage one for mid voltage and
one for low voltage now this AC power
control works by taking its input from
this regulator section up here this
consists of an opto coupler and a sense
amplifier the sense amplifier is going
to sample the low voltage it's going to
sample the high voltage and it's also
going to take an input from this DC
protection circuitry the DC protection
circuitry is tied to the output of each
Channel and it's just looking for DC on
the output so if there's anything wrong
with any of this circuitry here we're
gonna have a problem if I had to bet I
would say we're gonna have a problem in
either the AC power control or the
regulator circuitry so let's take a look
at the schematic and I believe this is a
scanned copy so the resolution isn't
that great but it works for this purpose
again I'm not gonna look at the audio
signal circuitry at this point we're
just concerned with the power supply
section so again we'll start on the
right this time with the line cord
here's our 10 amp fuse and here's the AC
power control circuitry consists of this
bridge rectifier these transistors of
course all of these resistors and these
two diodes and most importantly this
triac so I've never worked with a triac
I had to do a little bit of research on
it and seems to act pretty much like a
relay although it can conduct in both
directions which is useful for a seed
drive circuitry Laci is going to be
driven through the primary of the
transformer here the secondary as we
said is gonna have the three taps one
rectifier here one bridge rectifier here
and one down here one for the high mid
and low voltage respectively so if we
want to look at the regulation section
so again the AC power control was fed by
the regulator section we consisted of an
opto coupler which is right here as well
as the sense amplifier which is going to
consist of this IC 301 which is made up
of four op amps so again we know that
it's gonna sense or take a sample of the
high output so this op amp is gonna take
if we follow it down it's going to take
a sample of the minus 100 volts and the
other input is going to take a sample of
the positive hundred volts
and so it's gonna regulate based on the
inputs of those if either of those is
off its gonna send an output to the
photo coupler which is going to send a
signal to the AC Drive control and it's
going to regulate the transformer
accordingly there's another op-amp up
here which is going to sample the low
voltage and it's going to do the same
thing and then these two right here work
in tandem to sample the output for DC
voltage so with that in mind again my
suspicion is that we're gonna have a
problem in either this circuitry the AC
control or the regulator circuitry which
consists of the photo coupler and
basically I see 301 which is the sense
am the first thing I'll do is test the
pry-on of the secondary of the
transformer to make sure we have some AC
voltage we should because we had
something like 3 volts on the hundred
volt output so we should have some sort
of AC voltage here this is the secondary
of the transformer so we'll measure
Orange - Orange for AC we should get
something we'll measure brown to brown
that's the mid and we'll measure red to
red and then we'll move backwards we'll
check the primary of the transformer and
I think the transformer should be
working since we have some voltage so I
should be able to rule out the
transformer by measuring that and if so
we'll move backwards and we'll check the
AC control circuitry and the regulator
circuitry
I'll start by looking at the secondary
of the transformer here's the high
voltage rail and
only about three point nine volts ac way
too low let's check the mid rail only
0.9 volts AC let's check the low rail
one point seven volts ac much too low on
each output rail let's check the input
to the transformer the inputs good and
the outputs bad the transformer is
probably bad but no the input is too low
six and a half volts AC is not going to
give us what we need on the output so I
believe the transformer is working it's
just not getting the appropriate voltage
to do its job so we have to go backwards
and take a look at the AC control
circuitry previously I mentioned the
regulator circuitry as well but we don't
need to be concerned about that with
this start up this is a start-up problem
and so that regulator circuitry actually
needs the unit to be powered up before
it to operate so it needs the plus and
minus 12 volts to even operate so that's
not going to affect our power up what we
need to look at is the AC control
circuitry so to perform any other
measurements we're going to need to flip
it over so I'll flip the unit over
here's the schematic again let's take a
look at the AC control circuitry we have
live AC coming in at the top of our 404
you have two sets of transistors q 401
and 404 and Q 402 and 403 these are
going to work to alternately charge and
discharge capacitor C 405 and I turn on
this circuitry is going to send pulses
to the triac to the gate of the triac TR
401 and these pulses should allow the
track to conduct sufficiently to turn
the unit on now of course any component
in this circuitry could have failed I'm
going to start by trying to rule out the
triac so what I have setup now is I have
my oscilloscope probe hooked up to the
gate of the triac and I'm going to turn
the unit on if the AC control circuitry
is working properly we should see
positive and negative pulses at the gate
and if it's not we probably won't see
anything or it'll be misshaped so let's
turn it on and see what we get and we do
get nice pulses the positive a negative
pulses you can see they alternate there
so I am definitely leaning towards the
triac being bad since it's getting the
that have a negative pulse is that it
needs to conduct so I will order a
replacement I'll replace it and I'll be
back to see if that fix the issue
replacing the track did not fix the
issue here's the old one and let me just
run through the test with you on the
Atlas SCR meter so it does detect the
triac gives you the pin out it does
trigger at a current of somewhere
between ten and twenty five milliamps so
no problem there got a gate voltage of
about one volt at twenty five milliamps
and it shows you the load condition so
anyway it shows you that it's good and
so we wasted a little bit of money and
time on replacing that triac but now I
have a spare a good one
I did check all of the other components
in the AC control circuitry so those
four transistors that are critical the
capacitors that are critical the
resistors the dials I checked all of
them they're all measuring fine so I had
to kind of rethink what I wanted to do
where I wanted to go next so I thought
about maybe something on the output or
the secondary of the transformer that
might be pulling this down and so what I
did was I started checking for shorts to
ground and I found one and maybe I
should have done this right away or
sooner but I didn't so here we go if we
go straight to chassis which is ground
the short I found is right here and if I
put it in continuity mode there we go
definitely short so this is connector
p4o for pin three so if we look at the
schematic this is the this applies the
negative sixty volts and so there are
multiple components in this rail here
and I checked all of them the last one
that I forgot to check is the most
important and there's the one that I
believe is the problem is the only
component that goes straight to ground
which is capacitor C 414 and this is one
of the big ones
it's the 3300 micro farad at 63 volts so
you can see the capacitor here
or you can see the leads of it it
actually goes straight from this pin so
here's the pin here and it goes straight
to this in here that's the negative lead
of the capacitor and then there's the
positive lead so obviously they're
shorted so that doesn't necessarily mean
that the capacitor is the problem but
even if the capacitor is fine and we
have a short somewhere else down the
line in resistance mode we should build
up a resistance along that or across
that capacitor and I'm not getting any
so I'm pretty sure that this capacitor
is shorted I'm going to remove it just
to be sure
strike two the capacitor is just fine so
I have to get that reinstalled I took
another hard look at the schematic and I
found two more components that I hadn't
yet checked these two diodes and of
course these are the problem
so these are diodes D 408 and D 409 and
the junction of these two diodes is the
negative 60 volt rail so that was the
problem as I mentioned before I checked
all of the components on the negative 60
volt rail downstream of these and they
were just fine I also went backwards and
checked D 410 and D 411 to make sure
those weren't shorted and they were fine
as well and finally I checked again for
a short across pin 3 of P 404 2 chassis
ground and the short is gone so that's
great effectively what we had with these
two shorted is the two red taps off of
the secondary of the transformer were
shorted I'm still working on a theory
for why that would cause the failure
mode that we've seen but I'm still
thinking about that this one you can
even actually see a crack in it but I
show you that before I move on there it
is
so I have the replacements on order I'll
be back once they get them installed the
new diodes are installed and I
reinstalled the capacitor and check it
out it turns on now let's see how it
sounds
[Music]
alright it sounds great everything's
working as it should as I said I'll
probably recap this before I let it go
but I'm not gonna document that I just
wanted to document the repair and so
this one is finished thanks for watching
[Music]
you
