DR #31 - Audio Amplifier Repair - Parasound HCA-500

Duality Repair
132 followers
4 Video Views·Mar 12, 2025
In this video, I document the troubleshooting and repair of a Parasound HCA-500 that needs just a bit of work.
hey everyone welcome to duality repair
this is my first para sound unit this is
the HD a 500 high current discrete
amplifier I've already tested it and
it's got at least one problem may have
two or even more so let's test it and
you can hear the relay engage and
actually this time it worked a little
bit better than last time so I can hear
the left channel right now let you
listen for a second so you can hear the
music that's from the left channel the
last time I didn't hear anything I had
to tap well there you go
tapped on the cover just a few times I
didn't engaged I'm gonna guess that
that's the relay and boy that keeps
going in and out I look through the
cover and I can see the relay it looks
very very similar to the relay that I
had to deal with on my last unit the
Carver and so I bet I'm gonna have to
clean that relay but the other problem
is if I turn the left channel down you
can't really hear anything from the
right if I turn it all the way up and I
turn my input source all the way up oh
it sounds terrible you can hear it but
it sounds terrible so there's a problem
with the right channel and there's also
a global problem that's very likely the
relay so we have at least two issues
let's start by taking the cover off this
unit is rated at 50 watts of continuous
power into 8 ohms or 10 amps of
continuous current and so the large
transformer here is a must there are two
taps off of the secondary of the
transformer one is going to supply the
positive and negative rail voltages for
the amplifier section the other is going
to supply the low voltage for the unit
so it's going to be the voltage for this
LED here as well as the coil voltage for
the relay now as far as work I'm going
to start on this power supply board I'm
gonna remove and replace all of the
electrolytic they're in good shape but
they're all original and they're 85 C
rated so I'll get those replaced I'm
also going to remove inspect and clean
the contacts of the relay I can already
see through this cover here that the
variable contacts are there's a lot of
buildup on those and so I believe that's
causing our intermittent dropout issue
this relay is very very similar to the
relay that
was in the carver unit that I recently
worked on it is a guardian unit however
it does have a slightly different model
number but I think it's going to be
basically the same inside so I'm going
to turn this around
we'll get the service panel off and get
to work all right here's the relay and I
apologize but I've already cleaned the
contacts reinstalled it and tested it
but since it's out of the unit again you
know there's still a problem so I
believe this relay was actually causing
both issues because momentarily I had
both channel sounding just fine however
when I tapped on the cover I still got
it to drop out intermittently and so
I've already cleaned the contacts really
well really as as good as I could so I
don't think the cleanliness or the
surface of the contacts is the issue I
think it's the alignment of the variable
contacts with respect to the fixed so if
we look at the variable contacts here in
the middle you can see that with respect
to the fixed it's it's pretty far off
you can see almost half of the variable
contact there and so really if it slides
out of position like that which it will
after certain number of actuations it's
it's hardly making contact and you can
really see it here it's it's just not
making enough contact I believe and so
any little disruption so me tapping on
the cover
you know prevented complete contact
between the variable and fixed and I've
already looked at the the way this is
mounted I think it's actually a way that
it was fabricated this fabrication flaw
just a little bit of marginality in the
fabrication so I don't think I'm gonna
be able to fix this
and just to avoid any future pain I
ordered a new one I actually found a new
one on ebay and I think this is brand
new it said it was brand new the cover
looks really nice it's it's an exact
replacement so I think this should work
if we look
the variable versus fixed alignment you
can see that's exactly what we want dead
center basically even if we actuate it
it looks perfect so I'm gonna get this
one installed and then we'll test ok the
relay went in just fine and yes I did
recap the power supply board off-camera
I apologize for that I tested this and
the right channel is now working so the
relay was causing that problem but the
left channel still seems to cut out
intermittently so let's check that out
so you can hear this is both channels
they sound really great right now let me
show you just the right channel working
just fine let me show you the left
channel sounds ok but I tapped on it
again and it'll cut out intermittently
so what I think the problem is there's
some sort of connection issue on the
board somewhere down here so we have our
course our relay right here and we have
our output from power supply board to
each channel the red wire is the right
channel the blue is the left so watch
what happens if I manipulate the blue
wire there you go so I'm not doing much
there at all and it cut out completely
depending on where that sits it cuts in
and out so think at a minimum there's a
problem with this connection it could be
the wire to the to the post here or it
could be the post solder to the board
let's zoom in and inspect that a little
further ok I've been chasing the left
output wire there's blue wire here for
quite a while and it certainly seemed
like as I manipulated it it was cutting
in and out but that is not the issue let
me show you what I found
alright here are all four speaker
binding posts the right channel is in
the red and the black and the left
channel is in the blue and the black and
maybe you can already see the issue it's
not the positive signal it's this
negative signal right here this this
negative lead is not even soldered on to
the binding post and so I'm doing a bad
job of showing you there you go you can
see it's yeah look at that it's not
soldered on at all it's just sliding up
and down the binding post so that's
definitely going to be our intermittent
issue with the left channel
I'm not positive but it certainly seems
like this has been this way from the
factory it doesn't look like there's
been any solder on there at all so I
think the owner has just gotten lucky
that it hasn't cut out you know from the
very beginning but either way let's get
the solder on and make sure that fixes
this issue it's been reared so let's
test it now for stability so this is
left channel only it sounds pretty good
let me manipulate both the positive and
negative wires to make sure we're still
stable go down the positive let me try
the negative good there as well sounds
all good make sure the right channel
still sounds okay
[Music]
it sounds great so technically this
repair is complete everything is working
as it should
I've recapped the power supply board
replaced the relay soldered the left
channels ground connection to the
speaker binding post but we can't call
this complete without finishing the
recap so I will be recapping the
amplifier board I have all of those caps
depending on the age sometimes I will
remove and replace the thermal compound
behind the heat sigma2 transistors but
I've already checked this there's plenty
of thermal compound on all four
transistors actual six and it's in
really good shape it's not brittle or
dry so I'm gonna leave that the way it
is those are working really really well
so I'm not going to touch those I'm just
going to finish by recapping the
amplifier section
[Music]
the amplifier section has been recaps so
this one is completely done let's do the
final sound test this sounds great I
appreciate you watching we'll see you
soon
[Music]
you
