DR #42 - Pioneer SX 1980 Classic Audio Receiver Restoration - Chapter 1

Duality Repair
132 followers
2 Video Views·Mar 12, 2025
In chapter 1, I go over the basic layout of this Pioneer SX-1980. I service both amplifier boards and complete a modification for the unobtainable output transistors.
hi everyone welcome to Duality repair
and this is the Holy Grail of Hi-Fi the
Pioneer SX 1980.
my plan is to completely restore this
electrically the owner said he will take
care of the Cosmetic restoration so I'm
not going to worry about that
I know for a fact this is going to be a
very long humbling and rewarding
experience
so let's get started
here's the first look inside and it's
completely Untouched by me
I'm pretty happy as it appears that
pretty much everything appears to be
here and intact
there's a few things that have been
disassembled
this cover is missing
I think I've seen in some photos that
there should be a cover here but I'm not
positive none of that is a deal breaker
the ball caps appear to be original
those will get replaced
the owner has informed me that the unit
does turn on so that gives me a high
degree confidence of the Transformer
which is great
if that failed then this unit is
probably done
the tuner section here looks to be
original there's a lot of electrolytics
that'll definitely need to get replaced
I think I've seen a few that appear to
have failed
taking a quick look at the left amp that
all appears to be original and intact
which is great the right amp
unfortunately I can definitely tell some
work has been done either some or all of
the output transistors have been
replaced and they have not been replaced
well
and so I know that's a big sticking
point with units like this or this unit
specifically these output transistors
are very obscure very very difficult to
find Direct Replacements if not
impossible
and so we may have to do some
modifications there
but overall at least from the top
there's nothing that appears to be
stopping me from completing this
restoration let's take a look at the
bottom
all right here's the bottom of the unit
and
it's looking pretty clean
everything seems to mostly be complete
and original with the exception of the
work that's been done on this right
amplifier board up here so you can see
some of the work that's been done we
have two exposed wires here flapping
around in the breeze
can get a quick shot of these output
transistors that have been replaced
each of them are only actually mounted
with one screw it looks like
I found a wire down here this blue one
which unlike the rest of the unit is
soldered to its terminal
and then this fuse here
is doesn't look to be aligned properly
so that was probably replaced at some
point
so there are some points of concern
I don't know much about this unit yet I
know I will be well acquainted with it
come a few weeks or months from now
looks like we have some
words down here that lead off to the
front controls both on the bottom and
the top
we have the back of the tuner section
here and here
power supply board right in the middle
and I know from what I've seen in some
videos and read on the forums that this
board is subject to several issues so
I'm going to have to heavily scrutinize
this once we get that out I don't even
know what these are yet these two boards
will get to that
not sure what this section is up here
looks like some sort of power
distribution but we'll get to that too
so it looks good looks like I have the
green light to to get going on this
restoration I guess the question is
where to start
for me I'm most concerned with the
amplifier channels specifically with the
output transistor so I think I'm going
to start there
here's the right channels amplifier
board
and it looks to be in pretty good
condition everything appears to be
complete and relatively intact
all of these pins look like they're
starting to tarnish so I'm going to want
to clean all of that off so they're
making as solid an electrical connection
as possible
with the mating female pins in these
connectors here
there's only three electrolytics to
replace these two and the smaller one
here
just due to the age regardless of how
they test I am going to replace those
there's two transistors mounted to heat
sinks I'll pull those off the board make
sure those are measuring properly and
then clean and reapply new thermal
compound
I will measure every single resistor and
diode on here to make sure those are
measuring properly
there's one area of concern
it's this package here
you can see there's a crack starting to
form right down the middle
and inside this package is four diodes
in series
this is part of the BIOS circuitry and
it's mounted to the heatsink so that its
temperature can track with the
temperature of the output transistor so
it's a fairly critical component and
just like the output transistors this is
not available
so I am going to do what I have to do to
get this to function I'll probably glue
or JB Weld that
crack
so that it doesn't split any further I
did measure this and it's reading open
in One Direction and it's got the
appropriate voltage drop on the other so
it seems like it's measuring okay just
want to make sure that crack doesn't get
any worse
so I think recovering this board
shouldn't be too bad
that leads us to
the actual output transistors
all right where do I begin with yelpa
transistors so you can see that these
are not the originals these are sanken
2sa 1215 and 2sc 2921 pairs
due to the package difference between
these and The Originals they're only
amount of one screw each which is not
going to work
the wiring and soldering as well
extremely messy that is not going to
work either so everything on here is
going to have to come out it's all going
to have to be redone
these transistors for all I know could
be suitable Replacements electrically
but I am going to replace them with
something else
due to the difference in the package
size between the ones that I'm going to
replace with and The Originals I'm going
to have to come up with a custom
mounting bracket as well for each one of
these so that they mount properly to the
heatsink
and I'm going to redo all of this wiring
here as well just to make it as clean as
possible it's going to be a lot of work
but we're going to get it done
[Music]
all right here's the board removed from
the tray
it looks like there may have been a
little bit of work done
you can see these two packages right
here are the transistors mounted to the
heatsinks they may have been removed at
some point down here as well I believe
that's these two transistors
those as well may have been removed
I will
thoroughly inspect all of the solder
joints here and make sure that they're
all
solid if any of them are questionable
marginal I will Reflow them
we'll get the board all cleaned up as
well you can see some dust here
I think the first thing I'll do is pull
these two transistors and the heatsinks
off measure those and reapply a new
thermal compound
the right channels amplifier board is
practically done you can see I removed
all three electrolytics and replaced
those with new ones
just out of curiosity I did measure the
ESR and capacitance of those ones and
they are measuring just fine
I removed and tested these two
transistors here with the peak meter and
they were measuring just fine I
understand that's not a comprehensive
test but that's the best I can do
without a curved tracer
I applied new thermal compound to these
two heat sinks and then I also applied
some new thermal compound between this
package and this heatsink
I inspected every single resistor and
diode on the board and they're all
measuring as they should
I inspected
all of the solder joints on the back
here
most looked pretty good I did have to
touch this one up it was a little
questionable
and I found a few small solder balls
here and there that I had to remove from
the board
other than that this looks to be in
pretty good condition
I did apply some JB Weld to this package
here both front and back I'm hopeful
that that will prevent this from
cracking further
I did the best I could with that
this uh
form of JB Weld is good up to 230
degrees Fahrenheit so that should be
plenty high enough for the application
here
the last thing to do is just to clean
the tarnish off all of these contacts I
tried using some contact cleaner and a
toothbrush didn't really work well for
me so from what I've seen on some other
videos it looks like the best method or
one of the best methods is to use a
fiberglass pen so I have some of those
on order
once those come in I will finish this
board
all right so how am I going to solve
this output transistor problem I'm going
to use these two transistors here as
Replacements these are on semi mjl 4302a
and mjl4281a
these transistors meet or exceed the
specifications of the original
transistors
for power for current for voltage
there's only two potential problems
number one the transition frequency of
these is more than double that of the
original these are 35 megahertz The
Originals were at 14 megahertz
so we'll deal with that potential
problem in a moment number two is
obvious the package style so these are
to 264.
and there's no obvious way to mount
these to the heatsink
I thought about maybe turning them on
their side and mounting it either like
that
or like that bending the legs up and
that would work but it would make the
wiring a lot more difficult and it would
look a lot uglier so
I decided against that
what I did instead was being a buddy
from work use the CNC mill to create
these custom alumina brackets and these
are going to be awesome
so the transistor will fit really nice
and snug in this pocket
and then we'll use the holes on either
side
to mount the transistor to the heatsink
it's going to look nice it's going to
work nice really happy with this
this guy's got everything he's got the
CNC mill and he's got many other pieces
of equipment and very versatile guy he
can pretty much do anything you ask of
him so really glad that he was able to
help and I'm really glad I was able to
insist in the fabrication so thanks a
lot Tommy
I'm going to get these installed now
all right look at how pretty that is huh
these turned out really really well this
is going to work
they look nice and they're really solid
those transistors aren't going anywhere
I have Mica spacers and thermal compound
underneath each transistor so that
should provide adequate thermal
conductivity
next step is to get this wired up so I
will carefully bend the terminals of
each transistor perpendicular to the
heatsink so I have some room to work
there
to do the wiring I have I'm going to
have to mostly use new wiring so I have
the same size wiring as the original
this is 20 gauge in various colors
and to fix the wiring to the terminal so
I'm going to use this ring style
terminal with a hole just big enough to
fit around the terminal and then I'll
solder that together it's going to look
really nice
the bases are all tied together
the collectors are all tied together
the power for the collectors comes in
through the harness from the top and the
wiring for each emitter comes in from
the harness from the bottom
so I will have to reuse the connectors
on the original harnesses and a little
bit of wire other than that I'm going to
redo pretty much everything so
we'll get to work
all right here's the final result for
the right Channel's output section I'm
very happy with the way this turned out
I think it's going to work well I think
it looks really nice too
one thing to note are the two film
capacitors here these are each 0.1
microfarad at 625 volts
they're tied from each rails collector
directly to chassis ground here and here
I mentioned that there could be a
potential concern with the significant
increase in transition frequency between
the new style transistors the mjls and
the original Style
these capacitors are in place to
hopefully mitigate that concern by
filtering out any potential high
frequency
while I take 100 credit for the work
that you see here
this was all actually inspired by a very
very old thread on the audio Karma
website it started way back in 2006.
and so if anyone that was involved in
that thread happens to be watching this
just know that I appreciate you and that
threat is still relevant today
I'm going to get the board installed
back to the heatsink
and then I'll get this right channel
reinstalled on the unit and then I have
to do everything all over again with the
Left Channel
here's the left amplifier board
and it looks to be in pretty good
condition other than it being pretty
dusty
I plan on performing the same process to
this board as I did on the right channel
so I will remove and replace the three
electrolytics remove and measure these
two heatsink mounted transistors
and then clean and reapply new thermal
compound to the heat sinks I'll measure
all of the resistors and diodes make
sure they're measuring okay
and I'll clean the tarnish off all of
the contacts
and then do a general inspection of the
board top and bottom make sure there's
nothing noticeable that needs to be done
like touching up solder joints or
removing solder balls things like that
let's take a look at the output
transistors
this left channel has the original
output transistor straight from the
factory and you can see they were
actually using capacitors between each
rails collector to chassis ground as
well they're using a little bit
different capacitors these are ceramic
unlike the film that I used and the
values are a little bit different these
are either 0.47 or 0.047 microfarad a
little bit lower than the 0.1 I used but
it's the same Theory filtering out
extremely high frequencies that might be
present there
can be tempting to want to reuse these
output transistors because they are the
originals but they are so old so even if
they're measuring properly I would want
to replace them because it's there's no
guarantee they're not going to fail in
the near future and we don't want that
also I'm a really big fan of symmetry
and so in order to have each amp or each
Channel perform identically or as close
to identical as possible I'm going to
perform the same modification the same
transistor modification on this channel
as I did on the right Channel
out of curiosity let's check a few of
these original transistors see if they
are
any good
so it's able to detect the PNP
gain of 68
no leakage current that one looks good
let's see if the npn is any good
yeah it detects this as well
gain of 35.
and zero leakage current on this one as
well
I think I'll hang on to these anybody
need a set of these or three sets
[Music]
[Music]
[Music]
[Music]
thank you
foreign
[Music]
the left amp is done now too so far so
good with this unit
that's it for this chapter of the
Pioneer SX 1980 series stay tuned for
the next video when I'll replace the
bulk filter caps
rebuild the power supply board and
hopefully do a power-up test
thanks for watching
