DR #45 - NAD 1155 Audio Preamplifier Repair, Service, and Testing

Duality Repair
132 followers
3 Video Views·Mar 12, 2025
- Resolved intermittent output issue
- Replaced both power supply transistors
- Replaced all electrolytic capacitors
- Verified power supply and preamp functionality
hi everyone this is Nick welcome to
Duality repair and this is an NAD 1155
preamp
I've worked on one other 1155 in the
past but honestly I don't even remember
what the problem with that one was I
don't think it's the same as this one
though the complaint from this one is
that we get no output no matter what
input is used and I actually was not
able to reproduce the problem until
recently so let me turn it up I have a
one kilohertz sine wave at the input of
each Channel
and you can see we do get an output but
only from one channel
and I believe I've actually already
figured out the problem so if we take a
look at this listen switch which is
basically just an input selection switch
if I toggle that just a little bit
you can see we are able to get the
output from the other channel
so this should be a fairly
straightforward repair if we can get
this switch out of the unit if we can
get it open and service it so let's see
if we can do that
here's the switch in question the input
selection switch now the only way to
clean this properly is to remove it from
the unit disassemble it hopefully that's
possible
and to be clear all of the switches and
buttons and potentiometers in this unit
are of the same age and so they're
susceptible to the same problems that
this switch is so we will be pulling and
cleaning those as well but I do want to
start with this to make sure that we can
get a a reliable stable output from each
Channel
so to remove it there are a bunch of
pins to desolder on the switch itself on
the back of the board
looks like I'll also have to desolder
and remove this cable this cable and
maybe even this one I'm hopeful there's
enough play in this coupler here so that
I don't need to remove this rod and then
the knob on the front of the unit but
we'll see so let's start desoldering
here's the switch and you can see all of
the electrical contacts in the center
it's actually got two unpopulated
contacts it's interesting and then a
post in either corner
first thing I want to do though is
remove the two cables
and so I marked each set so here's the
first set of three marked it there the
other set of three so that's one cable
and then here's the set of four and then
this one's hard to see on camera but the
set of four there so I'm going to start
with those
some equipment is just an absolute dream
to work on compared to others
when it comes to removing components
take a look at how easily this solder
Wicks up
it's rarely that easy
I had to go with the larger braid to get
these
larger four corner posts
should be all of it see if we can get
the switch out
all right the switch is removed from the
board but let's see if we can get it
decoupled here from this coupler
yep there we go
it's a lot of pins
see if we can get it open
all right so to get this apart I think
we have to pull back
these three tabs and the matching three
tabs on this side
just kind of pull them back so that
they're parallel with this face here
and then might also need to remove this
c-clip
that's mounting the shaft to the switch
I'm not sure hopefully that's it I'm not
sure if there's anything else
tying this together but we'll start with
that
this is an interesting switch let's take
a look at it now that it's deconstructed
so we'll start with this I'm going to
call this the housing
and so we have our post here this goes
all the way out to the front of the unit
this is what you're rotating when you're
selecting your input and it's attached
to this plastic piece here via a gear
and as you rotate the knob
the plastic piece inside slides
back and forth within the housing
the plastic piece has four notches to
hold
these four sliders I'm going to call
them
so these little sliders slide along the
rail
back and forth as you adjust the input
selection switch
the outer end here is electrically
connected to this main post which goes
from end to end and then the center pin
goes to one of several contacts and
that's what allows you to
change the input selection so I think
it's pretty obvious here the failure
mode is just too much grease
there's certain spots I think that the
grease is impeding the electrical
conductivity between the slider and the
contact so
what I'll need to do is clean all of
this grease off reapply a little bit of
new grease and this should be good to go
all right I used a little bit of
deoxyd100l and some isopropyl alcohol to
clean it up and then added just a little
bit of super lube and I think it looks
really nice
should work just fine now so let's get
it reinstalled and test
all right the switch is reinstalled
let's take a look at the results I have
a one kilohertz 100 millivolt sine wave
at each input for the CD video input
let's take a look
you can see we have both outputs now and
they're both very clean and even if I
mess with this input selection switch
toggling it back and forth there's no
marginality there at all on the output
I've tested all five inputs and they're
all working just the same so I'd say
cleaning that switch definitely resolved
this issue fantastic
although the main complaint with this
unit has been resolved while I have this
unit I want to do as much as I can to
Future proof it
and so the next thing I want to look at
are these two transistors here these are
the series pass transistors and they're
responsible for regulating the plus and
minus 24 volts for the entire unit you
can see this area the board is a lot
darker than the rest of the board and
that's because that's the power supply
section and so that means any component
in this area and especially these two
transistors have seen a lot of heat
throughout their life and it's probably
shortened them to the point where they
should be replaced and so I'm going to
replace these two transistors here
here are the two transistors I'm going
to use to replace the originals it's an
a1220a and a c2690a the specifications
for these transistors meet or exceed
that of The Originals so these should
work just fine
let's take the old ones out
pretty easy to see how dark the back of
the board is as well
not much thermal compound left on the
original heatsink and transistor
I'll clean that heatsink and apply some
new thermal compound
the new transistors are installed but
I'm just not happy with the way that
they're mounted in particular with the
way that the heatsinks are mounted look
at this
the heatsinks kind of just shift
underneath
and it has to do with how
the screws are mounted to the bottom of
the board so let's flip it over
here are the heatsink screws popping
through on the other side and there's
just nothing to hold these down properly
and so that's why the heat sinks are
able to slide around so I'm gonna have
to come up with something better than
this
I used some new screws and self-locking
nuts and I'm much more comfortable with
how secure these transistors and heat
sinks are mounted to the board
I turn the unit on and I'm looking at
the collector of q601 which is the
positive 24 volt regulator and as you
can see we're sitting at 23.9 volts
according to the service manual we
should be somewhere between 23.5 and 24
volts so I'd say this is perfect let's
move on
up next are capacitors with the unit
being 30 or 40 years old and all of the
electrolytics being original they all
need to be replaced so here's my list of
capacitors for the unit the ones in
Orange I have the ones that are xed out
I needed to order so here are the ones
that I have in stock that I'm ready to
replace today all the rest are on order
they'll be here soon
there's really not too many that I need
to talk about maybe just the two in the
power supply so when we get there we
will talk about those let's get started
foreign
making some really good progress on the
recap I only have about 10 left as I
mentioned I think there are only a few
capacitors that are even worth talking
about it's these two here these are the
two filter capacitors for the power
supply so we have power from the
Transformer coming in here it is
rectified by the bridge rectifier and
then it comes into these two capacitors
as plus and minus 32 volts
now these capacitors are 1000 microfarad
at 35 volts and 85 degrees C now while
these do work I would recommend going a
little bit higher there's not much
margin between the 32 volts that it's
filtering and the 35 volt rating and so
I'm going with these
are neutricon 1000 microfarad same
capacitance but 50 volts so much larger
margin there and 105 degrees C so these
are a definite upgrade and fortunately
they are identical in size both diameter
and height and even the lead spacing so
they're going to fit in exactly as these
do
should work really well
and done
the recap is complete I think it turned
out really really well let's power it on
make sure our voltages are still good
and see if we can pass the signal
the power supply appears to be
functioning we're at 23.9 volts on the
positive Rail and negative 23.7 on the
negative rail
all right final test I have a one
kilohertz sine wave at the CD video
input I'll turn it up
and both channels look great
they look to be evenly matched
and if I turn on and off that switch
that listen switch
nice clean Transitions and even when I
toggle it doesn't drop out at all so
that's pretty stable now let's increase
the frequency and monitor the response
there's five kilohertz
still looks good
10
15 and 20.
it's good to me
so this preamp just needed a little bit
of love and I think it's ready to run
for many years to come
so thanks for watching we'll see you
next time
