DR #52 - Speaker Amplifier Repair - Definitive Technology CS-8080HD

Duality Repair
132 followers
8 Video Views·Mar 12, 2025
I was sent 3 Definitive Technology speaker amplifiers for repair. In this video, I repair the CS-8080HD center speaker amp. Most of this video is centered around investigating and repairing the amplifier's switching power supply.
You'll see troubleshooting using a multi-meter and self-made block diagram, parts replaced, and final testing using a signal generator and an oscilloscope.
hey everyone this is Nick with Duality
repair and here we have three Definitive
Technology speaker amplifiers on either
side we have Tower amplifiers model bp88
St and in the center we have a center
speaker amplifier model CS
88hd these are all sent in by the same
person supposedly none of them are
working properly and they all failed
right after the warranty expired so
we're going to go through these one at a
time for no reason at all let's start
with the center speaker amplifier all
three of these amps are class D
amplifiers which is why they're so small
and this one has just two main
components it's got the power supply
component on the right which looks to be
a very standard off-the-shelf power
supply and that's feeding into this
digital board here on the left which is
handling all of the audio processing
let's start by trying to verify the
functionality of the power supply so
it's feeding the digital board via this
four pin connector here so let's flip it
over and take some
measurements the schematics that I have
do not appear to apply to the center
amplifier I believe they're for the
tower amplifiers so the first thing I
want to do before checking for voltages
is to try and identify the ground pin of
our four pin connection here from the
power supply so I'm going to use the
negative lead of this capacitor here
check for continuity at each pin
Four
3
2 pin two is going to be our ground pin
so we're not going to look for voltage
there all three other pins however
should probably have some sort of
voltage on them I've applied power and I
can actually already hear a high pitched
wind coming from the power supply so I
know something is going on in there
let's take some voltage measurements so
we'll start with pin
one and we have positive 5 volts that
seems reasonable pin two we know is
ground we don't need to measure that pin
three volts also seems very reasonable
pin
four I get
nothing now I'm not positive but that
doesn't seem right there are four wires
coming from the power supply we know
that only pin two is ground I should be
getting something on pin 4
let's investigate
further let's take a closer look at the
power supply here's our four pin
connector right here and thankfully
they've added some labels on this side
of the board to help us out pin one is
labeled as positive 7 volts we were
measuring around positive five so if
this label is accurate we do have a
slight problem with this pin pin two we
already knew was ground but it's nice to
see that it's labeled as ground pin 3 is
labeled as -7 Vols we are measuring
around five so again there may or may
not be a problem on this pin pin four is
labeled as PS or power supply on so this
is actually just a communication pin
between the power supply and the digital
board and so I don't think we should
expect any voltage on that pin so there
may or may not be a slight problem with
this part of the circuit however that's
not my main concern if we move over to
this connector I actually missed this on
the initial inspection of the digital
board it's kind of hiding behind this
four pin connector here and this is
going to be our higher voltage this is
what's going to actually drive this
speaker so very important you can see
one pin is labeled as positive VDC the
other is ground however when I have the
power supply connected to AC power I get
absolutely nothing here so I think this
is where our main problem is stemming
from since I don't have any schematics
let's take a look at this very simple
block diagram that I made for the
switching power supply we have our main
120 volts ac being rectified and
filtered to produce plus 340 volts DC
this is feeding our first Transformer T1
T1 is going to have four taps coming off
of the secondary tap number one is going
to produce positive 17 volts this is
going to feed this pulse with modulation
IC which ultimately drives the primary
of this Transformer so this is a self-
sustaining circuit tab two is going to
produce 5 volts DC tap three is going to
produce positive 5 volts DC we know all
of this is at least partially working
the area of concern is right here this
fourth tap so if we follow this chain
all the the way to the end we should see
some unknown but High DC voltage here
which will drive the speakers but we
don't and if we follow this all the way
back I actually get no DC voltage even
at the output of this rectification and
filter section so this is where we want
to place our
Focus let's take a look at all four
rails of that Transformer T1 there's our
positive 17
volts there's our positive low voltage
rail measuring positive 5
5 here's our negative low voltage rail
it's measuring - 6.44 so perhaps these
both should be plus and minus 7 volts
but let's move on for now here's our
other Rail and again we should be
measuring some nonzero DC voltage and
we're only getting 47 molts that's no
good so let's see what can actually
cause
this there are only two components
involved in the rectification and
filtering of our unknown DC voltage rail
we have this single diode right here and
this single electrolytic capacitor right
here if I had to put money on it it
would be a problem with this
electrolytic but there's only one way to
find out so let's pull it out take some
measurements here it is this should be
100 microfarad at 25 volts you can see
we're only measuring .2 nanofarads so
there's no capacitance left in this at
all let's measure a brand new one for
reference here's a brand new one the
exact same ratings 100 microfarad 25
Vols you can see where measuring 101
microfarads so let's try replacing the
old one with this and see what happens
after replacing that capacitor we now
have a voltage on our mystery rail a
little bit over 21 volts we also have
something on our high voltage rail now a
little bit over 48 volts so it certainly
seems like this power supply is
functioning properly after just that one
component replacement let's flip it over
and take a look at what other components
we might want to replace before
reinstalling here's our mystery rail
capacitor that I've already replaced
I've also replaced some of the other
similar smaller value electrolytic
capacitors around the power supply I am
going to replace the rest of the
electrolytics so these four on the AC
side and these two on the output side
regardless of how these test replacing
them now will improve the longevity of
this power
supply attached to this heat sink are
two MOS fats they seem to be running
just fine so I'm just going to pull them
clean and reapply new thermal compound
I'll do the same thing for the diode
attached to this heat sink if we take a
look at this IC this is one of our
pulsewidth modulation ic's you can see
just how dark it is on the board
surrounding that IC indicating how hot
this thing gets when it's running it's
running okay for now but who knows for
how long so I'm going to replace
it
all right all done with the power supply
I think it turned out well let's plug it
in and make sure it
works not quite as soon as I tried to
play any audio the amplifier started to
behave erratically and I got absolutely
nothing from the output so I shut it off
and started to investigate the high
voltage rail I found that this diode
right here which is a shot key diode it
was shorted it's reading about 2 to 3
ohms lead to lead it was located right
here and this is the rectifier in our
mystery rail which is directly in line
with the high voltage rail just to be
safe even though they're measuring fine
I also replace these two shot key diodes
which were here and here these are the
rectifiers for our low voltage rails
plus andus 5 volts so let's test it
now everything appears to be functioning
properly now before we get to the final
test for reference let's check the
voltages one more
time pin one is positive 5.1 volts pin
two we know is
ground pin 3 is 5.3 volts pin 4 which
again is the power supply on pin this is
only enabled when we have an audio
signal at the input of the
amplifier and this is positive 3.1 volts
our high voltage rail this also is only
enabled when we have an audio signal at
the input to the
amplifier and this is positive 48
volts since this is a subwo for
amplifier we have to use a very low
frequency at the input I have a 100 HZ
at 1vt sine wave at the input to the
amplifier I'll turn up the volume and
we'll take a look at the output on the
oscilloscope looks
beautiful if you've watched my channel
you'll know that I typically prefer
using an oscilloscope to demonstrate the
ability of audio equipment over using a
speaker or set of speakers you just
can't get the sound quality over a video
but everyone can see the quality of an
audio signal on an
oscilloscope
this looks
fantastic that's going to do it for the
repair of this Definitive Technology
Center speaker amplifier model cs88 HD
the repair attempt of the two tower
speaker amplifiers model bp88 St will
have to wait for another video if you're
curious about what parts I use during
this repair I will flash a list of those
at the end thanks for
watching
