How to set up a boat building jig - Building Gannet - Episode 7

Nomad Boatbuilding
98 followers
3 Video Views·Mar 10, 2025
My website: https://www.nomadboatbuilding.com
Instagram: https://www.instagram.com/nomadboatbuilding/
It's not about the money but living isn't free...
Here are some ways you can support this channel:
Buy some merch: https://www.nomadboatbuilding.com/shop/
Support these videos with monthly or annual pledges at Patreon: https://www.patreon.com/nomadboatbuilding
Or make a one time donation: https://www.paypal.com/paypalme/nomadboatbuilding
hi welcome to snow my boat building I'm
Mark huden and today on building ganet
we're going to tackle what I consider to
be the most fun and satisfying part of
the entire project and that is setting
up the building jig so I got all my
plank and stock scarfed got the glue
cleaned up gave them a quick little sand
we got all our molds ready to go there's
nothing left for me to do but set up the
building jig so I'll just start at the
back and start working my way forward
we're just going to align these molds to
the center line screw them in place and
then we got spend a bit of time Plumbing
them up and bracing them now if I was
really smart which I was not this time
around I would have made sure that I had
some blocking on each mold that was
consistent in height that I could just
fasten a bat into easily sometimes I
just use the keelon itself that we put
on to do that job for me that might work
pretty good in this case cuz we got a
pretty flat keelon for the most part if
it's got a lot of crown to it if there's
a lot of rocker in the boat as you bend
that down it can sort of affect the plum
of the mold so I don't always like to
use that method I think it might work
out okay in this case so maybe you'll
just go ahead and do that what I want to
do right now is just start stacking them
up and screwing them
down now I want to make sure that I've
got the correct face against the correct
side of my cleats that's very important
so in the AF portion of the boat I need
to put these molds after of the cleat
and my reference face is on the back
side that means that the larger part of
the boat lands on the waist side of the
mold if that makes any
sense just start by clamping them in
place
what I love about this part of the
project is in a very short amount of
time we have big results this is when
all the effort you put in at the lofting
stage when you're making the molds when
you're building the strong back it all
comes together in a very satisfying
way this is also the stage at which you
finally get to realize the real scale
proportion and shape of the boat
you get a good idea of it when you're
lofting but that's still two-dimensional
now it's three-dimensional and you
really get to feel that this is the part
of the project where my students would
often use the Expression it's starting
to look like a boat I find that
expression a little irritating for some
reason but I will give them that this
truly is when it is finally starting to
look like a
boat SPO so wide I can't reach the other
side to tap this thing both ways if I
need to
[Music]
I started out my career as an artist and
Industrial designer and I was also
interested in sculpture but I like to
work at a slightly larger scale
sometimes that's really not practical as
an artist unless you've got a market for
it
and for me it was the craft was the more
important thing not an artistic Vision
so when I discovered boat building it
really took all the skills that I had as
an artist and Industrial designer
brought it all into one package that
really satisfied me and it still
does from a practical point of view it's
still a sculpture but it's something
that has some use it doesn't just sit
statically now I have done a few boats
that are just for display and I'm fine
with that I enjoy doing that it allows
me to produce a boat that is not
necessarily built entirely to withstand
the rigors of being on the water
although I usually try and build them
such that they could because you never
know what's going to happen with
something that's hanging on a wall or
from a ceiling someone might decide to
throw it in the water one day but in
general boat building is just a great
way to express
yourself even when you're working with
someone else's design there are so many
elements of the con construction process
that require your personal touch your
sense of taste and proportion and no
boat building plan ever has all the
answers drawn into the plan quite often
there are areas that you need to figure
out and so that's where Innovation comes
into play and of course there's just the
challenge of trying to build this very
organically shaped thing with products
that are usually not organically shaped
to start with they're manufactured into
rectilinear objects
and we need to transform those into
roundish objects and that's really where
the fun comes into it for
me if you're watching this channel
you're probably interested in trying
boat building for yourself if you
haven't already and I encourage you to
do so I suggest you just start at a
small scale do some model making that's
a great way to learn and then when
you're ready to build a full-size boat
start with something small again
something small and simple for your
first try even a small simple project
will deliver valuable lessons to you
that you can apply to a larger project
later
on if you join me over on patreon at the
$5 sponsorship level and up you'll
receive a free set of plans for my
forest and stream model skiff it's a
great little project to get you started
in wooden boat building give you a sort
of taste for the thinking process you
need to go through for building any sort
of
boat and if patreon isn't for you you
can go over to my website and purchase
that same set of plans for $5 you can
find links in the corner or down in the
description either way helps to support
this Channel and helps me to continue
making videos for your education and
pleasure I think I might stop and
quickly do my bracing because it's
usually the center mold that I'll brace
and right now I can just get in here
easier than if I put the other molds in
now I got to kind of squeeze between
them to do the work that I need to do so
I'll take a moment to do my bracing okay
for bracing I'll
typically just start by clamping a level
onto the mold
here myself something to reference and
I've got a a stick on the back that's
going to be my
brace so I just want to play around with
it see if I can find the right
positioning for the
stick I might just make this temp then
grab a different one and fit it
differently
right there looks pretty
good okay because these are so wide I'll
brace both sides of it I think
there we go
good now it should be apparent why I
didn't want to set these molds up until
the last possible moment suddenly the
this boat takes up all the space in the
shop
all right now the very last
one
uh
right yep this one had to go on a little
different just want to make sure
100% yep okay
okay now to just brace it all
together think about this for a moment I
think I'll put a baton in here and just
spring it up into place and see how it
looks see if it'll work or if I need to
fudge around with some
blocking I could
also I would have to notch down into
here in order to fast in it from the top
which isn't the end of the world but it
means farting around with
a multimaster which I don't really feel
like
doing okay I got an
idea I just need to add a little bit of
blocking on a couple of these and we'll
be good normally I would often Notch the
tops of the molds and lay a Stringer in
there in order to connect all these
molds together I didn't do that in this
case because I was working from a set of
plans that didn't specify that sort of
detail so I guess I'm just kind of
rolling with the punches on this I'm
having to add a little bit of blocking
to make the Stringer work but that's
okay it's really not slowing me down
more than a few
moments okay so the basic idea is you
got one plumbed up and then you put a
baton in here that the other ones can
fasten to and you Plum all these up
accordingly
now I can uh I could Plum them or I
could use measurements from one to the
next which might not be a
terrible way to
go so in theory that should be
Plum and going check it on this side
yep that
works the only trouble is my clamp is
right in my way so Mark the
stick drill
it there we go
[Music]
all right there we go there's our
building jig set
up so that should work just fine
everything's Plum it's all secure enough
little wobbles no big deal for what
we're the way we're using it so now to
put the backbone onto it which consists
of the stem the Keon and the transom I
don't remember if I got all the notches
the right width for the Keon because I I
think I did but I might have screwed one
up or two so I got to play around with
that a little bit the transom we should
be able to just drop right into its uh
its supports that we got built back
there and then the stem of course we
need to take some of this blocking away
for the stem to drop on but before I put
the stem in place I just want to check
my plans and see if there's like a
trailering eye or something that's going
to go into it this might be a good time
to actually pre-drill for that
but no cuz I got the inner and outer
stem maybe I'll I'll save that for doing
the outer stem
I'll drill through there yeah we'll do
that
okay we're done with the center line
possibly better leave the center line in
place get the transom on first and then
when we do the stem I don't need it so
transom
next I always leave my transoms proud
and square on the edge so that I can
fasten it to transom supports like this
CU I find it's easier to just screw them
on than and than it is to try and uh
worry about making a support that
conforms to a contour of a transom crown
and sometimes you might want to tweak
how the transom looks when the boat's
finished so I prefer to do it this
way now I just need to Plum up from my
Center Line string onto the transom to
get it centered
here we
go and we'll just screw that
on we're ready for our keelon
all right I no longer need my String
Line Get rid of
that get rid of
that get rid of
that and now my
stem should just drop right on there
looks pretty good
[Music]
of course it never fits on your first
try and often your
second and sometimes even your
third this was probably my
fourth and that's quite good enough for
epoxy Construction
now I still need to complete the
backbone by gluing and screwing the Keon
to the stem and the transom but for the
most part that's it for the building jig
and now we get to feel the real size and
shape of the boat now you see my kilon
wasn't fitting those notches perfectly
so there's a few spots where I've used
some shims or little bits of blocking to
help tweak it into the right position
nothing wrong with that that's part of
the game and our next job will be
fairing in the backbone to accept the
planking so that's it for today's video
but before we go I just want to thank
everybody out there who watches these
videos and especially my followers on
patreon Whose financial support makes
these videos possible so hope you join
me again next time on building Canon and
until then let's stick together and stay
strong see you later folks
[Music]
