Thank you to everyone who has been supporting our channel! If you use the link below before you purchase anything on Amazon, we get a royalty for sending you there, thank you!
Our store is located at 139 Caldwell St., Rock Hill, SC 29730.
ladies and gentlemen this is Joe's
classic video games back on another cool
arcade game pinball machine repair video
for you this afternoon now if you've
watched our earlier video we get a video
where we repaired the playfield
repainted the playfield on this Space
Odyssey that we had in that was in
horrible condition play field was really
rough the cabinets fairly rough the back
glass is really rough and the game
doesn't work so we're we're working
through fixing this sucker and we're
filming it for all of our friends on
YouTube so this is our second video the
first one we did the playfield so we
have just finished the play filled up
reasonably and so now we're going to do
a video where we try to get the game
working and then finally we're going to
do another video where we try to save
that completely destroyed back glass
which is going to be tough so like I
said in the previous video we were able
to repaint some of the playfield and put
it all back together everything's
looking pretty decent on the play field
considering where it started and so now
we're going to check out the mechanics
of it and go through a systematic way to
repair an en pinball machine so the
first thing that I notice is that in the
back box there was only one damn light
bulb on you see it there's one light
bulb one and you can see how bad the
back glass is you can see right through
the glass a lot of the paint is flaked
off in horrible shape like I said that
would be another video but the first
thing we're going to do is try going
through it and just seeing if it does
anything so I'll hit the start button I
don't know if there's any credits on it
okay start sweating doing nothing
let me try adding a credit
savage like it out of the credit but it
didn't move the didn't move the credit
window nothing let's see alright so
basically we can't even get a credit on
it which I assumed it would be pretty
much not doing anything so the first
thing that I'm going to do on this one
is that's annoying the hell out of me
that none of the lights on the back box
work so I'm going to turn the game
around we'll start working in the back
box and I'll just show you how you can
repair these things if you have the time
and the patience so we'll do we'll do
the back box part first all right so
I've just angled the machine out a
little bit from the wall just so you can
see in the back a little bit and on
these this is a two-player game so on
these now there was also a four player
space mission that has more score rules
and a little bit more stuff going on
back here but on these two players
they're fairly easy Pro not fairly easy
but easier than the four players
certainly to work one so these are the
second player score rules these are the
first player score real you've got a lot
of light bulbs right these are some
options for public for high school this
is the coin unit I believe they call it
the coin unit on Williams basically it
tells you how many credits you have this
is probably the match unit there maybe
yeah it looks good I'm thinking the
matching it not sure what this is maybe
a ball count unit I believe so yeah ball
count unit possibly and then over here
you have all these Jones plugs you also
have a bunch of relays doing various
things like resetting and the score
relay so the first thing I'm going to do
because I've got the problem with the
lights is I want to take these three
Jones plugs off here that connect the
bottom of the cabinet to the top of the
cabinet and I'm going to clean them so
I'll pop on the results and show you
what I'm talking about
okay so there are the three sockets
either and plug the plugs of course I
turn the machine on before I did that
and as you can see they're different
sizes but also they'll only go one way
because this little metal thing
keeps them from going you know upside
down or whatever so these are the these
are pretty good this is a Williams
machine and these are these are built
the sockets are built pretty good on
some of them like the valleys they have
they're made these are made a little
different and they tend to break these
particular ones on the Williams one
don't use liberation and then here you
have the Jones plugs itself so it's like
a wafer and then it has these metal
posts and I did that just so you can
remove the head from the bottom there's
also other ones on the machines that if
there's something else that they want
removable or if for like options and
things you can pull out the plug and put
it on the other side to make a three
ball and five ball or whatever but what
happens is they get real dirty so focus
a little bit so you can see that there's
just grime and dirt all over them
they're oxidized sometimes they even get
rusted and because of that they don't
make good contact anymore so the first
thing I'm going to do is clean those I'm
gonna take some some fine sandpaper you
can use like a wire brush or something
too and just try to shine those up and
get them to look a little better we'll
put them back in and see if it gets
anywhere light bulbs to come on so
that's the first thing be back
all right so this is how they look after
you clean them up a little bit just want
to get them nice and shiny so they're
making good contact and I put it back in
and the other two back in and look what
happened
same exactly but at least now we know
those are clean so let me show you
something what this likely means and I
kind of knew that because if it's
getting voltage the one they're all
getting voltage check this out
take one out put a new one in that's
right
every bulbs burn out so we're going to
swap all those out and then we're going
to start doing the rest of the back box
okay folks I replace all the light bulbs
and yes they were just all burnt out but
I needed to clean those little things
anyways I'm trying to show you how to
get one where it works great so we
cleaned all that which is a big deal all
of those lines are there if you look
that's the only thing that connects the
bottom to the top so all of those wires
are important to score right for the
coin unit to work right bubble blah so
after I did that I went back and put a
credit on it and this will still didn't
move so it wasn't adding a credit for me
so I just went ahead and manually added
a credit on it so now we have seven
credits I'm going to start button again
see if we get anything even if the thing
starts working we've still got a lot of
work to do I'm just trying to see where
we're at for the video
all right so it's trying to reset and
Tessa keeps going oh it kind of it kind
of kind of kind of stops and then it
went the game over so again we've got
stuff that's not working right you know
it tried to reset everything it's
supposed to reset all those reset some
of the bonus Stepford unit underneath it
reset the ball count unit blah blah blah
and then kick the ball out but instead
it tried to reset for a little bit got
hung a little bit and then the game over
light came back on so we still have a
lot to work through so the next thing
that I'm going to do is uh I think I'm
going to clean the score rules and some
of the stuff in the back even though
that won't get us up and running but I'm
just trying to do it all to get the
bakbox done so we'll start on that
alright so we're going to start cleaning
up some of these relays I'm shining a
light on so I can kind of show you how
they work basically on these machines
these electromechanical machines they
have switches that are on banks of
relays and that's how everything works
so these relays pull in you can see that
there are two wires running to it
basically whatever makes the relay pull
in and then it pulls in like that well
as it pulls in this actuator moves it's
hard to do all this on low enough hands
this actuator moves and it moves all of
the switches this is a good one to show
you because they're all making brake
switches so let's look at this let's
look at this first one there you see
that
notice how the center switch the center
blade goes all the way up and then on
either side is a shorter blade so as you
can see right now the center switch is
touching the blade on that side right
they call this a make and break switch
so it's touching the one on the right
and then when the relay pulls in it will
open the one on the right and touch the
one on the left right so if I can get
some light on there where you can see it
okay watch this so when the relay pulls
in its out let's go with the right one
and it touches the left one and then
whenever it goes not it lets go to the
left when it touches the right so all of
your switches will be either make or
break switches like that
or like they will be see these two here
these two switches how they're open
because the the actuator is pulled in
watch when I take off the actuator
now they're both closed all right and
then down here on the bottom this is a
good one to show see how this switch
right here then my thumb fingers on if
you look closely it is connected and
then it's one over here if you look
closely it is not connected so when the
relay pulls in it will connect this one
and it will disconnect that one right so
that's the other one on the left that's
connecting right opening so this one is
a normally closed that opens when the
relay goes in and then this one is a
normally open that closes when it really
goes in so basically you need to go
through all the relays and make sure
that they're doing that so when the
relay goes in it should change states
you know and if it's a make or break
like this it'll it has two different
things that it has to hit and if it's a
normally closed like this it needs to
open then if it's normally open like
this it needs to close so you need to
get through and make sure all of the
switches look like they're adjusted
properly now I wouldn't suggest
adjusting them you know don't go through
and adjust every switch because
sometimes even if you're not positive
that they're working every note if
they're touching good enough or whatever
usually they are because they they kind
of whenever they whatever they touch
they move a little bit and that's
supposed to actually like clean the
contacts
so usually if the game is this one
hasn't been working in a long time so
but usually on most games and almost all
of the switches are adjusted properly
you'll just find a couple that are
obviously out of out of whack like
they'll be bent really bad or whenever
you pull the relay end they never touch
and then when you let go but they never
touch anything so you know that switch
something has to be going wrong now to
clean them what we use that you can use
different things the old-school way that
they used to do it was people would use
like a business card or something so you
could actually slide like a part of a
business card or a little piece of paper
like card stock through the contacts
just to clean them all most ours are
pretty grimy so we actually use you
can't now you can't don't freak out
about this you can't use like a file or
anything that's super aggressive on
contacts because you'll end up pitting
and scarring the tip of the face of the
contact screwing it all up so what we
what we actually usually use is we have
a lot of files that are old and worn out
and the only reason we use them is just
because they're flat so you can get them
between the things you can't use a file
like if this was a new file I couldn't
use it because you'd be scratching up
all the contacts but these files we've
got files that are just worn pretty much
smooth where there's hardly any kind of
grit to it anymore and so for us that's
real convenient we've got a few of those
where we can just go through and you're
basically rubbing the dirt off of the
contact you don't want to use a file
where you're going to be scratching and
scraping the contacts that will screw
everything up now on the on the flippers
you'll get contacts that are big like I
don't know if they're tungsten or
whatever these big thick contacts that
have that'll be all pitted and scarred
and everything because there's so much
power running through them on some of
those you have to actually use a file
that has a pretty good abrasive powers
to it but on these we use something real
smooth that doesn't that can't scratch
the crap out of everything right so we
went through and adjusted these in the
back box
what we've got left is this little match
unit up here we've got to clean the
score reels and we thought we would go
ahead and clean the I think this is the
ball count unit because there's five
little basically positions that it can
be in so we're going to take this apart
and show you how to clean one of these
up now the first thing you'll notice is
that it is filthy still set right and we
need to get it where it will move freely
through all of its stuff so let's see if
let's see what it does so I'm just going
to pull in this relay here and I'm not
real a Akoya leer and say it'll step up
so that must be the one that resets it
this one isn't doing anything so
basically this is part of our problem
this isn't just setup isn't doing
anything I think I might even have a
spring missing here so we're gonna start
taking that apart and check it out the
first thing I'm going to do is take this
nut off so I can take this off and clean
this board up clean the end of the
fingers on the spider and then we'll put
it back but I'm probably gonna drop some
lubricant on the metal too so I'll put
down the camera so that I can do that
and then I'll come back in just a second
okay so I went through what I did was I
loosen the nut took it off took the
spider off and then took light sandpaper
and sanded the all of the copper nice
and shiny and then I put a little bit of
synthetic grease on it that's you can't
use anything that's electrically
conductive the dielectric grease would
be good just a light light bit of that
right and you clean the back of the
fingers right and then the whole shaft
pulls out this is the gear this whole
shaft pulls out you have to get this
spring just right make sure that these
switches these switches whenever you
pull this out it'll hit these switches
but usually
you can just kind of bend them to the
side while you go by it and it doesn't
bend them too far out of shape and then
I looked in my parts in the back and I
had a string to replace the one that's
missing right got it all cleaned up and
cleaned everything oiled it and put it
back through tightened up the spider so
the way this should work is every time
the Machine tells it pulls in this one
coil the spider should advance up one
position and it's not just this
connection you know there's like six or
seven on there and this should all turn
look one turn all right and there's
different ones so you kind of got a look
at each one and then this one right here
on the top whenever it pulls in the
spider should reset all the way to home
position never mind my hands I got dirt
all over I've been cleaning on this
stuff so when I'm going to just simulate
this plunger going in and the way it
does it too is just something to think
about is that it doesn't do it like this
that's not what happens whenever it
whenever the game does it it does it
pretty violently so it's like this so
you kind of got them you kind of got to
do that so that it's operating like it
will operate in the game
so you can see it spins it should it
should advance one step each time I do
and that's glass step it won't go any
farther than that now the reason it
won't go any further than that is
because on that gear I give it the focus
one that gear there there is a tooth
missing on purpose so that it can trap
it pass that's fun now when I pull this
one in it should reset all the way back
to the home position the first spot
right and it did now that's the easy
part because since I had it so far
around this spring has so much tension
on it that of course it will reset all
the way down so you have to get it to a
happy medium where that spring is strong
enough to reset it all the way back to
zero but not so strong that it's almost
impossible to step the spider up you
know what I mean so you have to get it
kind of in between so you need you need
the spring to be loose enough that you
can actually fight against it as it
steps up and you need to have it strong
enough that it can reset it all the way
beginning now the hardest thing to get
it right is it should be able to reset
from the first position right so see I'm
on the first one now when I reset it it
should go back down even though there's
almost no tension on that spring and it
did so I've got it sometimes if you
don't have this tight enough basically
if you if you're on like the first
position or something
it won't reset because the spring is not
wound up tight enough so to get it just
right where everything's oil everything
is working right you have to get it work
and do that so we did that and then the
next thing that I'd went ahead and did
was I cleaned most of the score reels
I've got one apart here though that I'm
going to show you how it works these are
the ones that I've already cleaned you
can see they're nice and shiny and
adjusted those four snap them back in
place and then over here I've been
working on the other four now on this
particular machine there's a big harness
that goes up and then they slide it into
place and so it's easier to just pull
out all four of them at the same time so
I've cleaned three of them and I'm down
to the very last score reel so this is a
big mess here
I kind of once twisted let me see if I
can twist it back out goes okay so
what's going on trying to get organized
here without about pension of hair off
all right so that's kind of how it goes
those three go up into place and then we
have this fourth one here that I've
started taking apart this was the last
one so what you do is there's a little
retaining clip on the end and you pop
that off and then it's kind of tricky I
can't really give you a best way to do
this because I still struggle with it
but there's this plunger inside of it
with a spring holding it to here and
then this little thing here has a spring
holding it too
so your problem is is that it stretches
out halfway up on a gear inside of this
plastic thing so it's kind of hard to
pop this whole thing apart with those in
the way so yeah it kind of pull them out
of the way with your finger and
manipulate something off of that so
that's kind of the hardest part of it in
my opinion but once you get that off you
can pull out the plunger now these are
Don Williams ones obviously ones in the
corner these are Williams score reels
and this is from the 1975 machine some
of the other Williams ones I believe are
a little different and in some of the
the guide looks are different the
valleys are different but they all kind
of have the same idea going on they're
just set up a little different so now
that we're down to this bakelite plate
I'm going to do the same thing I'm going
to clean these contacts because
basically this will these little things
right around the world now the only real
purpose of that the reason that these
have to be clean is for the match to
work and for the high score to work so
you don't really need to do it but I
always do it because I want to match to
working on time to go to work so we're
going to clean that we're going to clean
up the
we'll we're going to put a little bit of
dielectric grease on that too just a
little minor amount you can't put a
bunch we're going to clean up this wheel
too what happens is they sit in the game
on 0 just like that right and after they
sit for 40 years
there's all this dirt and grime on the
top of the reel that was sitting upright
all these years if you get one that was
sitting on three for years then the 2
and the 1 and the 0 on the 9 will be
during but this one was sitting on 0 for
years and 9 8 7 6 or I'll filthy alright
so we're going to clean that all up
here's one that's been cleaned just so
you can see the difference you don't
have to get it perfect another thing too
a good way to clean these is not with
Windex or anything like that it will
actually make the ink run on some of
them some of them it doesn't some it
does it it's hard to tell which ones are
which
but uh one of the one of the little
piece of devices use wax just wax and
the wax actually cleans wax as a cleaner
it's not just a shiner okay so we're
going to do that and then the other the
last thing that you have to worry about
is you have to adjust the switches so
let me see if I can get one out here in
the light where you can see it a little
bit yeah um so I've seen where I sent
just try this one so you have an end of
strokes which there so when the plunger
pulls in it opens that switch if I get
it to do it see how that switch opened
up and then it closes when the plunger
goes out to have to get that adjusted
and clean and then just like you have
switches on everything else in the
machine you have these little rad
switches here
so you can see what's going on all right
so this there's this plastic cam that
comes down here and it goes inside of
the score reel and the score rule
manipulates it as it goes around so when
you're on two three four so whenever
you're on one two three four five six
seven and eight the behavior is the same
so you see the top switch this
particular Williams is closed the middle
switch is closed and the bottom switch
is open now you can see as I move it
around that does not change all right so
we're on eight so now I'm going to move
over to nine and watch what happens when
I go to 9 I should I did it too slow
I'm now on nine now look what it did the
cam went down and closed the bottom
switch now the reason it did that was
because it just connected itself to the
next score room so if you score one more
point since that switch is connected
it's going to move this reel to zero
right and it's going to move the next
reel up one on one place right now the
next reels on zero so it will move to
one so that's how they wired it up to
where it counts past you know into
double digits and then there's one on
the on each consecutive reel so that's
on nine now when it when it when the
game starts it wants to get them all
back to zero right so watch what happens
whenever you send it to zero so whenever
the real goes around to zero all three
open up right so the top ones open the
middle ones open and the bottom of open
that's the most important thing about
the story reels you got to get where it
says that again this is on a Williams it
may be different I've seen them where
they're backwards of that so like
they're open on one through eight and
then they close when they get to zero
and stuff like that so you got it you
can kind of tell what they're supposed
to do by just messing with them and
looking at them oh okay I see when it
gets to nine that goes down so it must
be supposed to make that that switch
closed and when it gets to zero these go
up so it must be supposed to open us you
can tell all that just by kind of
messing with them but you have to get
all of those doing that right and you
can you can also tell by looking in
schematics how they're supposed to be if
you're if you if you're not familiar
enough with them to be able to just
eyeball it but you have to get those
switches right and that's why you'll get
games where they'll try to reset to zero
and it'll just keep going and going and
going and going and going and going and
going because of those switches on one
of the rules probably the one that's
still going and sometimes you'll get
them where it will start a game with the
score will reset so it'll be one like
480 514 it'll be on like zero one zero
zero that one that's stuck on one it's
because that one switch has opened up so
it doesn't the machine thinks it's on
zero so that's one of the that's one of
the the biggest things of getting the
scoring right you have to get all of
those where they where they step from
one two three through each thing fluidly
and then you have to get them where the
switches work properly whenever it gets
to nine and whenever it gets to zero so
what I'm going to do is on the slide
those back up in there I'm still going
to clean this little match unit up
basically I'm just going to take this
little thing off the end on these
Williams they have this interesting
little thing where there's a sorry you
can't see it too good but there's a
little like a little clamp that holds it
on the end so I'm gonna take that little
clamp off clean that that bakelite PCB
and then the same on this side just to
get it clean and where they can move
around good and then on my credit unit
here everything is good on it you can
see a coil has been replaced at some
time I'm just going to get where it
moves I don't think it needs oiled or
anything because it doesn't have a
bakelite I call it bakelite it might not
be bakelite but it doesn't have a fiber
board thing that touches it just has
some switches that it it's as it adds or
subtract I credit so I'm just going to
clean those switches up make sure that
steps around like it should and then I'm
gonna call the back of the game done and
we'll start inside the game so be back
all right folks so we're going to stop
the video there because this video
turned out being really long
over an hour long so basically we
finished up the back of the back
topography we'll be doing the rest of it
in the next part of the video which you
have to wait till next week we'll see
I'm showing you a few pictures of the
playfield so that I don't spoil what
they were all so it ended up looking
like but I'll just tell you we did did
it's going so we'll see you next week
with the rest of the video make sure to
leave your comments below give us a
thumbs up because we're so cool and that
makes the word subscribe to us we'll see
you next time ok love
[Music]