Thank you to everyone who has been supporting our channel! If you use the link below before you purchase anything on Amazon, we get a royalty for sending you there, thank you!
Our store is located at 139 Caldwell St., Rock Hill, SC 29730.
ladies and gentlemen Joe's classic video
games back with another cool arcade game
repair video for you today we've been
working on this Spy Hunter arcade game
and did a video on it already so if you
haven't seen it yet the link is below go
check it out how we went through the
first part so basically we tested
everything and got the game up and
running but now we're to the point where
although it's running it's got a hump
bar going through the screen and we've
got a jumping car here so that's our two
main problems with the game gameplay at
least so the first thing that we are
going to do is we're going to rebuild
the suitcase power supply down at the
bottom of the game which has a bunch of
large capacitor for a couple large
capacitors in it and so we ordered those
and we've gotten them in and so we're
gonna pop that out and replace those in
it so we'll pull that suitcase out and
take a look at it on the bench alright
folks so this is what it looks like out
of the machine you can see it's a little
rusty but you've got a fused block two
big caps here you got a plug there for
the service so you can plug like a
soldering iron or something and if you
want this is where the main plug the
power cord plugs in a bunch of the
ground straps plug in there the wiring
harness a bunch of ground wires plug in
here and then all of your AC switches
and everything plug in here and then
these are the two wires that we were
talking about on the first video they go
up and plug into the power supply like
that so everything is controlled by this
thing so since we've got like a wave
going through the screen we've got a
problem with one of these two caps and
we're gonna replace both of those and
Raavan replace this little oil filled
one here I've heard that you usually
don't have to replace this one but I had
a kick man one time where that burnt up
and actually caught on fire so I replace
it if you're going through the trouble
to replace these this is like an extra
six bucks so we replace it too so we'll
take the screws out of the side here
and look inside of it alright folks so
this is what it looks like with the back
of the bottom off
it's actually really clean so you've got
the two filter caps here which we have
got replacements for from our cage shop
my buddies at arcade shop so when I was
a 56,000
and one of them is a hundred thousand
MFD and this is that little oil cap it's
it's like a starter cap for like an air
conditioner basically so that's how you
can get one I think the original is like
a 3.7 you have for something like yet
but they make for UF it's really common
so this is what we order very
inexpensive because they're still used
like I said in air conditioning systems
and it goes them right so when your
power comes in here it goes over to this
distribution block goes through some
fuses you've got a line filter here
these usually don't go bad it goes
through out into the cabinet for
switches and things like that the power
comes back in you've got this
transformer here where you've got you
know your primary voltages and your
secondary voltages of 12 volts and 115
volts so this is a I believe the 115
volts would probably be for your monitor
so that's all isolation transformer and
then the 12 volts I believe is used in
this particular game this 12 volts I
think is used for the light board I
think I might have that wrong you've
also got this transformer over here
you've got these diodes over here that
rectify the voltage the DC I suppose and
you've got the two big filter caps so
this isn't usually gonna go bad your
diodes can go bad but usually these kind
don't usually whatever you get them
these are fine I guess their diodes
mr11 - oh I've never had to replace this
I don't know usually your filter doesn't
go bad and usually your transformer
doesn't go bad so the problems you're
gonna have are the two big caps and this
little oil cap and like I said some
people don't even think that you have to
do anything with that so we're gonna
replace all three of those and then this
thing is gonna be kind of you know ready
to go so I'll start taking one of them
out alright folks so it all came off
really easy so there's the new oil cap
and there's the old one it's a 3.5 so
like I said we put a four in and then
the hundred thousand UF we put a hundred
thousand ufn and then this was a fifty
thousand and we put a fifty six thousand
which is a more common size I guess if
you go up a little bit on these it
doesn't matter the date code I'm not
sure about but that 84 I believe that's
it right there so it was the 19th week
of 1984 I believe and so on this one
let's see what it says the 33rd week of
1983 and on this one
perhaps the 25th week of 1983 maybe if
I'm guessing so this this game probably
this is the newest one we had was the
19th week of 1984 so this one was
probably actually made in 1984 sometimes
they would come out in 83 and then
they'd make them for a year or something
I don't know but there you go put them
back in we're going to put the base back
on it and you can see that the can it
wasn't as tall and the two caps aren't
as tall but they're new now and I also
found inside of it one penny and the
date on the penny is
focus I'll have to read it for you
the date on the penny is 1987 okay folks
that we reinstalled the power brick in
the bottom the coal suitcase and then we
have turned on the game now we need to
check the voltage again just to make
sure it's not too high but look at this
our hum bar is gone now in the video you
might see a little thing rolling through
the screen that's just the camera that's
not the you can't see that in person
with your naked eye and look at the car
it's not jumping anymore so there was AC
getting through on the board's some kind
of AC ripple it wasn't filtering to
power very well and it was making the
car jump around so power supply it's
looking pretty good and if you listen
it's real quiet too so we got rid of the
buzzing and everything in the humming
that it was doing so the next thing that
we're gonna do is we're gonna see about
replacing that battery on the power
supply so we pulled out the board and
let's look it over a little bit hope you
can see well so the problem that you get
on these and this isn't all of the MCR
type stuff
is that it has this battery up here in
the corner and if you look it's already
starting to corrode just a little bit
but just a little bit and the reason
that this one hasn't corroded that much
is because if you see it's actually been
replaced that's them that's not the
original one so at some point so this
isn't a so this game came out and what
83 84 I guess 84 it was built we were
looking at the caps so from 84 we're now
in 2018 that's 34 years was my math
right right
eighty-four ninety-four 2004 2014 yeah
thirty four years so this is not a 34
year old battery it still might be a 30
year old battery it's not a 34 year old
battery so luckily it looks like most of
the corrosion is confined to there and
there and the purpose of this was the
save the high score a lot of times when
you get these this will have corroded
and the traces start corroding so all of
this will be corroded all of this will
be corroded which is basically in this
high score area but if it gets down into
this it gives you a bunch of problems
this is like your reset area there's a
reset line that helps start up the game
so I've even seen them where like
everything's corroded it just ate up
everything and an another strange thing
that it'll do is it'll it'll get in the
trace the trace will look fine but over
on the other side wherever the trace is
going
it'll be corroded away over there so so
we're gonna replace this now there's a
bunch of different things you can do
what a lot of people do is they say oh
that's a design flaw that shouldn't have
been like that whoever whoever did that
is so stupid that they did that I'm not
gonna do that I'm gonna put two wires on
it and I'm gonna run up a line over and
I'm gonna mount the battery on the side
of the game so there if it ever leaks it
won't eat up the board it'll it'll drip
and leak acid over on the side of the
game and all that and that's one way of
looking at it the way I look at it is
that's original this is original design
and the reason that it was a problem is
because the operator didn't change the
battery in 30 freakin years so to me
what I typically do is I just put a new
one right back on it and then I sell it
to I'll tell them I say hey there's a
battery on it you need to change it
sometime in the next 30 years so it
doesn't heat up the board and more
realistically you should probably change
it every eight or nine years and look at
it every once in a while just make sure
it's not doing anything but I guess you
could consider it a design flaw but to
me it's not it's not a huge deal just
change the thing every once in a while
that one the
like on the Bali pinball's we do put
mount a remote battery just because that
one's so famous you kind of can't you
have to you can't really get away with
selling one with that battery people
always go did you did you did you put
the remote battery holder on it I mean
it's not got that old battery I heard
the battery eats these things up so we
always take it off of that one and
there's other things you can do you can
put a capacitor you can put a different
type of battery on it that doesn't
typically leak you can do things like
that but we usually just put the same
type and just tell people I want
something like this we're kind of like
on a spy hunter you know we're kind of
trying to keep it where it's kind of
it's an original thing now the other
thing is a lot of people will take this
power spy out throw it in the trash and
put a switching power supply in it they
make these adapters where you can put a
power supply and just a regular modern
power supply but the problem I have with
that is I've done that before and I
ended up with all kinds of interference
and the sound you would get like a lot
of humming and stuff and it just it
didn't work right for me so these things
in my opinion are pretty reliable I'll
point out this one's still working you
know this thing is still working in a
thirty years old or thirty four years
old so I like the original ones I try to
keep it original now in sum I replace
you the you know depending on the game
I'll put a different I'll put a new
power supply and if I think the game
warrants it but if it's like these MCR
games I always just rebuild the original
power supply you get you got to look out
for that battery and make sure it hasn't
ate the whole thing up but if it's a
nice clean one like this and this is a
very clean one man I'm just gonna fix
this up put it right back in and this
thing is gonna be original which I would
prefer you know the other the other
thing that I was gonna mention is these
do have like a reset line so basically
when the game comes up it comes up in a
so the game runs off five volts so
whenever the game comes up the 5 volts
kind of goes
you know them is created so the logic
chips on the game board don't really
like that you know they want it to just
be 5 5 volts so what they do is they
they build this
set set up into the power supply so that
the board is also looking for a reset
signal and so the reset signal
it's either it holds low and then goes
high or hold high and goes low I always
get them confused because it's different
on different games but basically so I
say it holds it low so at the very
beginning of the game for about a second
or something like that it might be half
a second the power supply holds the
reset line which is one purple wire that
comes off one of these two connectors it
holds the reset line low for like half a
second or one second and that gives time
for the 5 volt to come up to where it
needs to be the 12 volt to come up to
where it needs to be and all of the
power to get through the wires over to
the board and everybody's got the power
it needs and then the reset goes and
turns the the reset sends the reset
signal high or it might be vice versa
but and it basically turns the machine
on so basically the reset signal holds
the Machine off for about half a second
until all the power gets stabilized and
then turns it on so the the modern the
switching power supplies don't have that
so basically the way they the way that
most people do it is you just unhook
that wire which leaves it floating or
you just tie it to ground or tie it to
five whatever it's supposed to be and so
then what happens is a lot of times
whenever the board boots up it comes up
yeah you know spazzing out and then
after a couple seconds it goes man
something's wrong and the and the
watchdog on the board says man we need
to reset this and it resets the board
with the watchdog signal on the board so
like if a game board comes up and it's
it's a it finds that something's wrong
it'll reset itself so the game board
will reset itself with the watchdog and
so if you if you tie it to the five or
the ground or whatever it's looking for
a lot of times that'll work but it it's
not how it's designed so some people who
cares right and I'm you know like on
space invaders for instance sometimes
will replace the power supply on space
invaders with a switching power supply
because it doesn't seem to cause that
many problems but on MCR we like keeping
these nice original
they go linear power supplies in it so
what I'm gonna do with this one is I'm
gonna replace the battery and clean that
up so that there's no corrosion on it
and that's out that's not acid that's
alkaline actually I'm gonna replace the
battery and I'm gonna replace these caps
just because these are electrolytic caps
they have like a liquid inside of them
originally and that I guess it's like a
paste but over time it dries out and so
they're not as effective so they have a
value like this is 470 UF and it's it
can handle 35 volts over time that 470
UF will drift because the the paste or
the whatever inside of it will dry up
and after it does that it's not doing
what's supposed to do so electric
electrolytic caps that are 35 years old
and that have been in a heat situation
definitely want to replace those and
then we also have these little gumdrop
ones here so there's so these these caps
like this those are called tantalum caps
those damn things are known for shorting
so basically they'll get where the the
two leads inside are connected together
I guess it's probably a similar thing
that was something inside of it
shorts together for whatever reason
tantalum caps are known for shorting
together so we always replace those two
with electrolytic caps now the tantalum
Kleck caps are more accurate so they're
the way I understand it I'm not an
expert at this but the way I understand
is that a tantalum cap is used whenever
you want something to be precise or at
least that's how it is now so if I could
say this is 470 UF well it may be 480 UF
there may be like a 10% variance in an
electrolytic cap but on a tantalum cap
it's either gonna be 470 or 471 I mean
it's gonna be real close that's how I
understand it but I think back in the
day and again this is just my assumption
I may be wrong but I think back in the
day they use these a lot of times for
like price reasons so I think about I
put a brand new electrolytic in it over
the years the electrolytic 7 better than
they used to be so it's my assumption
again I may be wrong but that a modern
electrolytic is better than this
old-school Tannen
and a modern electrolytic won't short
together as easily as these old-school
tannins once we're gonna get rid of
those and then finally you have these
these little gumdrop ones these are
called mylar caps so mylar caps are good
as gold usually you usually don't have
any problem out of these so you kind of
have to know the difference between them
but you know they look like little tic
tacs or something you know like little
Chiclets right so mylar cap is probably
fine
mylar cap is probably fine now they
could be bad if you get a problem and
you're looking for a problem
look you know look at them they might be
bad you can test them and things but a
mylar cap probably good mylar cap
probably good mylar cap probably good
probably good probably good tantalum
we're gonna replace tantalum we're gonna
replace electrolytic we're going to
replace tantalum we're gonna replace the
electrolytic we're gonna replace if I've
got that value and so you know it's just
simple stuff here
now on the back you can see it's
actually been working on before
obviously somebody to replace the
battery at some point but you can see
they've restored all of the pins on the
connections so that's a good idea
sometimes those will get cold solder
joints around they did it up here on
these two as well they replaced this for
at least resolder this 3501 too and 3501
this one looks original every soldered
that part and they reese odd 'red this
transistor here so they may have
replaced that it's a tip 31 so this
thing's already been working on in
antiquity so the only other thing that
I'm going to do is remember how we were
turning up the 5 volt so I've got it
turned up almost all the way so if you
replay that might be because like maybe
this cap or this cap are starting to
screw up inside so I want to turn that
back down before I plug it back in
because if I've got it turned all the
way up right now and then I put new caps
in it may bump the voltage up so it
maybe want to turn it back in instead of
putting out 5 volts like we had it on or
4.96 or whatever it was hell I might be
up to 7 now or something because it's
fixed you notice I don't want to do that
some will turn that back down I hope
that's the 5 volt one I'll double check
to make sure that's the 5 but since it's
all the way up pretty much that must
have been the one that we were turning
all the way up so I'm gonna turn it back
down just to make sure we don't plug it
back in so basically we're gonna plug it
back in and check the voltage again so
but that's the type of stuff that we
work through so I'm gonna do what we
just talked about replace a few caps put
up a new battery in it and then we'll
see what we got some of you will be
pleased to know that I didn't have any
of the original batteries so I had to
put a remote battery on it and I didn't
have that cap so we're just gonna leave
it but if you if so if you put a remote
battery it's real easy to do
basically we're just extending the lead
you know from where you would put the
positive lead and the negative lead out
on some wires to a little battery holder
and then we're putting in three double A
batteries the original battery that was
on here was a three point six volt this
makes it about four point five three
batteries that are 1.5 volts each and
then you have to put a diode because the
board will send power back to the
lithium battery and recharge it
I guess it's lithium you know what I
mean
so you put a little diode and it makes
it where it can't charge it and it also
lowers the voltage a little bit so you
put the band on the diode towards the
red line and that will make it do what
it do see it looks like there's already
a diode there so it may have all it may
not charge on this board but it's not
going to now because we put a diode in
it but due to shortness of the
original-style batteries I had to put
the remote battery holder some of you
will applaud that so we'll put it back
in the game and I'll test the voltage
again and then we'll move on to the next
name alright folks so we are back in
there we adjusted the voltage again and
things are back how they were so I think
what we're gonna do is stop for here and
stop for this video and then next time
we're gonna work through the the other
boards so the main PCB board what we
need to do to hit the audio amp some of
the little stuff and then the sounds
good board I think that's called the
sounds good board right am I wrong
no that's the cheap squeak deluxe valley
always had these really interesting
names for all their boards that video
board the sounds good board and the
cheap squeak deluxe so we'll be back
soon with the rest of it as we work
through bringing this thing back from
the dead and then eventually we'll play
it that's probably what you want to see
right but uh subscribe to us if you
haven't already give us a thumbs up for
taking the trouble to film all this and
leave your comments below on what you
think about what we've done so far we'll
see you on the next video