Thank you to everyone who has been supporting our channel! If you use the link below before you purchase anything on Amazon, we get a royalty for sending you there, thank you!
Our store is located at 139 Caldwell St., Rock Hill, SC 29730.
ladies and gentlemen this is joe's
classic video games back with another
cool pinball repair video for you
[Music]
we are working on this old williams f-14
tomcat pinball machine from 1987
and this thing has seen better days
pretty rough
[Music]
so we did a video when we got it in of
the condition that it was in and the
thing
actually still boots up but you can't
play it the solenoids don't work
um about half of the bulbs don't work
half of the displays don't work
and it's just pretty rough overall but
we're going to bring it back
so uh stay tuned if you like saying
seeing things turn back the hands of
time
so the first thing that i'm going to do
to it
like i mentioned we already did a video
where we kind of showed the condition
that it was in whenever we got it
the first thing that i'm going to do to
it
is when you have a big mess like this so
you got a machine that just got all
kinds of problems
you can't start like you know the so you
might be
tempted to oh let's just clean the play
field and work on that well it don't
even work you know let's get it where
electronically
it works properly first so the first
thing i'm going to do is start on the
electronics
and the way we tackle that whenever you
have a big project like this
is you need to cut it down in a bite
size problems people
bite size problems there's a thousand
things wrong with this thing but if you
think about it like that it'll overwhelm
you so you need to break it down into
the smallest pieces you can and then
slowly work through those okay
so the way i start is at the wall
the power comes in goes into the cabinet
and then pretty much the first thing it
does is it gets up here to the power
supply
so we're going to work on the power
supply first now the thing is up and
running
so the power supply is working
but you hear all the hum and the
speakers and everything and
that may be a power supply problem that
may be a problem over here on the on the
motherboard and all that
but it's a thing where you don't want to
work on the mpu
if you haven't made sure that the power
supply is good
you know what i mean you don't want to
go mess with the sound board
if you don't know that the mpu is good
so we like to do them in order kind of
the way the power
flows through the machine so the first
thing that you need to get right
is your power supply so i'm going to
turn it off
and then we will unplug this sucker and
put it on the bench and see what's going
on
now a couple things about it one it
doesn't have all of the burnt wiring
that these often have so these general
illumination
connectors often are all burnt up
this one isn't though for whatever
reason so that's good
and then two someone has soldered a
couple wires to it so there's a black
wire
soldered there and there's a red wire
soldered up there
i have no clue what those go to
shouldn't be like that and it ain't
going to be like that
when i'm done with it so the very first
thing i'm going to do is look and see
where those wires go
and what in the world they were trying
to do with that
so once we figure that out we can cut
them loose
fix whatever that problem is and then
we'll be able to remove the
power supply which just screws in
and everything unplugs general jaegoff
is yelling at me
we're coming to get we're coming to get
you general jagoff
i know i can't get you yet but i will
soon
um so let's see where those two wires go
they run down underneath into the
playfield area it appears
so i'll see i'll see what it looks like
underneath there
big mess underneath the play field but
look what i have here
a black and a red wire that someone has
added these are connected to the power
supply
[Music]
and if we get those loose
maybe we can figure out what in the
world
i guess that's just all
they made the wire too long i guess
runs over to here
okay uh
is in that loom as well
okay
what in the hell were they trying to do
we have duct tape on the coin door
boy it's old duct tape too nice
you just run into stuff like this people
it's not the end of the world or
anything it just
it is what it is and make sure that's
the same ones
yeah so it's this how in the world
what in the world
could be that one you wouldn't think it
would be in that bloom
though hmm it's very strange
you see it runs
into the okay the black one circles
around to here
it's plugged into this
meter coin meter that they've added
okay okay so let me think so
i've got a ground and a
it's just set up so they can make a coin
meter work
hmm
the red wire that's attached to one of
the voltages on the back
runs up into here
and then
i suppose
they've got it hacked into the coin
system somehow so that it can
make this coin meter work the reason for
that is because the the uh
the machines didn't have a physical coin
meter it was a
it was a software thing where it kept
track of it in the software
so someone was has went to a lot of
trouble to add that coin meter
that's crazy okay so we're going to cut
the two wires loose
i'm never going to attach them back it
will never go back on there
i don't want the coin meter the physical
coin meter to work i don't think that
helps anybody
and this uh this machine is going to be
in home use anyways so
the software accounting ought to be just
enough for
home use you know um
so yeah okay so i'll cut those off the
power supply and then i'll remove it put
it on the bench and we'll take a look at
it
and see what kind of condition it's in
all all over
so here's the power supply it's actually
very clean like i said usually the
general illuminations all burn up this
connector this one
not at all doesn't seem to be anything
at all wrong with it uh the wires that
they attach this one is on ground it's
on test point 2
which is ground which is weird because
you could have grabbed ground anywhere
and then this one is the 5 volt
grab 5 volts off of it to run the meter
i thought the meters were 12 volt meters
but maybe that's a five volt one
um so yeah we're just gonna get rid of
those two jumpers i mean those two
lines and at one point it looks like
they had the
the ground connected here to the 12 volt
or there was some kind of wire connected
to the 12 volt
we're getting rid of all of that so
we're going to
rebuild this a little bit the first
thing i'm going to do
is i'm going to reflow all the
connectors
so just the pins on the back sometimes
we'll get cold solder joints
i don't see any obvious ones on this one
but when you remove the connectors it
flexes the pins a little bit and
especially the ones on the end
will actually break away from the solder
and cause you lots of problems none of
these
have any obvious ones that i can see
but just for preventative maintenance
i'm going to do that so let me do that
first and i'll show you how that looks
all right new solder on all of the pins
for the connectors
that's kind of a must because that's a
that's a big problem cold solder joints
but it doesn't really cost you anything
so if you're working on one of these for
yourself
i'm trying to show you how to fix it
starting at the beginning you know so
that's one that you definitely have to
do
okay the next thing i'm going to do just
because i it's easy for me to do is i'm
going to replace
these three capacitors
because i just happen to have those we
keep capacitors in stock
now it looks like
those may have already been replaced
see if i can tell
i can't really tell by the solder joint
but possibly
so replace this capacitor this capacitor
this capacitor and this capacitor
usually those aren't really even
absolutely necessary it's not an
emergency thing you know they're really
cheap and simple to replace those so you
might as well do it if you're going to
do it but
the one that's very important is this
one this big one
so this is the uh 5 volt filter
capacitor so the the 5 volts that every
board runs on
is filtered by this um so when these get
old they start drifting
and uh letting a little ripple through
on the line or
your five volt will be too low or
whatever so uh
it's a good idea to replace this one so
you can buy these new on ebay
um several places you can get them
so i'm going to swap that out and i've
actually got the right one that's
axial instead of radio i always have the
wrong ones
for like these for instance uh so i'm
gonna swap that out
uh if you're looking for uh parts
there's a few good places you can get
stuff so great plains electronics
is a really cool place
greatplainselectronics.com
um does a lot of uh
pinball related stuff there's a place
called big daddy enterprises
that does a lot of pinball stuff they're
cool
and then the typical places like the
pinball resource pbresource.com
love them uh marco specialties is near
us here in south carolina
they that's probably the most that that
place probably has more stuff than
anybody
um as far as one one place that just
having a big variety of
pinball related things but components i
would probably go with
um great planes electronics if it's
if you can if they have what you need at
least i don't know if they sell these or
not
um and then uh if you're looking for
specific stuff like uh
or not specific stuff but generic stuff
like some of the tools we use and things
like that
you can check it out on our website we
don't really sell anything but there's a
bunch of links there
on our parts page just go to
lionsarcade.com
up at the top there is a place uh
there's a link to parts
and we've got a lot of the tools and
stuff that we
use or our t-shirts and our coffee mugs
with our logo and stuff like that on it
you go check all that out if you buy any
of this stuff that there's a link to it
sends you to amazon and we get a little
tip for
whatever you bought on amazon after you
click one of those links so
uh but i'm going to swap this one out
and then we've got to look at the uh the
high voltage
i need to see what this one is for too
my problem with this one is i don't have
a radial one all i've got is
i mean i don't have an axial all i have
is radial ones
so i could swap it but it's gonna be
kind of
ugly wait a minute
yeah i can't do it like that okay so
let me swap that one and then we're
going to look at the high voltage
section
okay so we got our new capacitor in and
put a little zip tie on it there's holes
in the board for that
this one i was trying to remember how i
usually do this one
if you look the positive lead can go
it can either be an axial or there's one
right there too
where you can put a radial in if you
want
so that leaves us with the two
capacitors for the displays
and then we need to think about bullet
not bulletproofing i don't really like
that phrase bulletproofing
preventative maintenance on the high
voltage
so the display is actually working you
may have noticed like
half of the display is not working like
the two top displays but the two bottom
are
the way it works is it uses a negative
100 volts and a positive 100 volts to
make everything work
but each display needs both of those so
the power supply is fine if you're
getting any kind of
anything on the display um the the
reason that those top two are out is
going to be
uh because of the
alkaline damage from the batteries on
the cpu or because the display itself
has problems
uh it's not the power supply so this
this power supply is working just fine
but what we want to do is is replace a
couple of the things that
fail often on it so that hopefully we'll
catch it
before it fills so one of the things is
these little resistors here are these
big resistors here
these are 39k
ohm resistors 39 000 ohm resistors
these these uh just take so much
uh i don't know what the best way to put
it
you get so much heat going through them
so much they're used so much that they
start drifting after a while
so they will change their value
sometimes you can measure them and
they'll be fine but then once they warm
up a little bit they change their value
so it's a good idea to replace these 39k
resistors with one watt flame proof
resistors okay
and then these these two little diodes
here are 1
in 47 64
diodes and that's what actually
regulates it to
100 volts and negative 100 volts so it's
one in
47 64. so what some people do is they
will replace these with
one in 47 63s
so they're 47 64s some people will put
47
63s because what that does is it lowers
the voltage to
91 volts instead of 100 and it makes it
negative 91 instead of negative 100 so
that means you have less voltage going
through your displays it makes them last
a little longer
the only problem though is if you have a
display that's borderline it's already
starting to
wiggle and there's pieces of it missing
and
because it's outgassing
if the voltage is lower it may make it
where the the
display won't even light up anymore so
it's kind of
half in one half in the other if you do
an led upgrade you don't need any of
this
so this area can be broken and the led
displays will still work so you know
it kind of just depends on where you
want to go what i'm going to do is i'm
going to replace these two resistors
and i'm going to replace these two
diodes
i'm going to use one in 47 65
47 63 i believe i do
have yeah i see them up there
i'm going to use the the 91 volt ones
the
the the uh
i hate to call it an upgrade because
there's you know the one in 47 63 so i'm
going to use those
and i'm going to replace these two
resistors and then i want to leave the
rest of it because it's
everything's working but these are known
to
drift and whenever they drift they blow
these diodes so the the diodes
start getting a little shaky and these
resistors start getting a little shaky
so by replacing those hopefully we'll
make it where uh
down the road we don't have any problems
these capacitors i believe
have already been changed i don't think
those are the original ones
they look pretty nice so i think
somebody's already worked on that area
so i'm gonna leave those
and we'll go from there oh another thing
you want to do is of course check your
fuses to make sure they're the right uh
the right amperage
so we'll check that too but let me let
me replace those resistors and die
and diodes and then we'll come back and
check it out
okay so we've replaced those that i
mounted them a little high off the board
just because heat's an issue on these
you know
and then the the fuses these were fine
the quarter amp that's for the displays
was a one amp so i made it a quarter amp
uh this one was correct uh this one was
a five instead of a four
and this one was correct so we're going
to pop it back in and see if everything
still works
keep your fingers crossed mine don't
really cross that well look dude
let me see if i can keep your fingers
crossed
okay we're going to check some voltages
on it i've got the i've got her turned
on
so we're very carefully going to check
some voltages
you can get a ground from like the back
plane or you can just touch one of the
screws is what i usually do
and uh i've got the inputs plugged in
this is the general illumination but
i've got the inputs plugged in but i
don't have the outputs plugged in
because if like the five volts is off
you don't want to send
like i may have this screwed up where
it's sending out eight volts or
something
well i don't want to send it over to the
boards i want to keep it on the power
supply until we confirm that it's the
right voltage
so
we're at 5.01 volts dc
boy thick can the harder one to do
is the uh the
high voltage for the displays because
you've got pins here right next to each
other
okay so what i did was i just put a
little uh empty molex connector on it
because that way i can't accidentally
short
to the pin next to it or something 5
volts like supposed to be i think that
was the key
100.5 volt
negative 103.5 volts so he says a little
bit off
um but you're talking it's three percent
off
ah that's pretty close those resistors
are probably five percent resistors
so if it's within five percent they
consider that
good to go right so the tolerance is
pretty close
um and you know that i put the uh
hmm that's interesting i put the 91 volt
diodes in it but i guess since we're
getting more uh
voltage from the transformer it's higher
but
whatever so basically
wall voltage has went up over the years
so if you're not
getting 110 volts out of the wall the
volts out of your transformer will rise
to so if it's
uh like i'm getting 120 out of the wall
here so
everything is like you know nine percent
higher
than it was so instead of 91 volts
and negative 91 volts we're at 100 and
[Music]
103.
thing i put those in if i want to put
the 100 volt ones in it probably would
have been much higher
okay but uh that's within tolerance i
think we're good to go
uh the five volts is right the display
voltage is right so i'm going to
very carefully you know turn it off plug
everything back in and see if we're
where we were
hopefully we haven't made anything worse
yet
it seems to be back up and running
now you die the displays are doing what
they were doing before
just barely limping along
okay so if you didn't see the first
video the reason that the displays
don't look very well is because there's
some pretty bad battery damage
not crazy crazy bad but it's leaking all
over all that crap
and this is the display connector right
here so
we're gonna have to do some extensive
rework
extensive rework on that
main pcb so join us next time when we'll
get right on that
we also have to uh since we're doing
power supply stuff
eventually we're going to have to put
fuses in these lines here see these two
bridge rectifiers if you uh
if you don't fuse those lines that that
feed those so there's two ac lines that
come in
and then the dc lines that come out of
both
if you don't put a fuse um
on the you have to cut one of the red
lines and put an eight amp fuse in it
and you have to cut uh one of the blue
lines and put an eight amp fuse in it
if you don't do that if those bridges
ever short and go bad
they catch the the wires on fire
we actually had one do that on one of
our videos one time
so since we're doing power supplies i
should mention that we'll do that i'm
just not gonna do it tonight but we'll
do it uh we'll do it in a later video
whenever we
start buttoning up things uh but yeah
next time we're gonna have to do some of
this
repair on this stuff
okay so
we hope you enjoyed it leave your
comments below give us a thumbs up for
taking the trouble to film it for you
it didn't fix anything really but at
least now we know that our power supply
is within spec
all of the numbers are right there where
they need to be this is where i got what
the
fuses were supposed to be i actually put
a little
legend on the back of the door here it's
slightly different on some of them some
of them will have
you see how this one has had a little
piece of paper stuck over it
it's because those change depending on
what's in the game
which title it is so there you go so we
appreciate you hanging out with us
tonight like i said leave your comments
below give us an odd number a thumbs up
and we'll catch you on the next one make
sure to check out our brother channel
my brother donny he's literally my
brother uh
and he and i are have lately been
working on a uh
an old building that we bought so if you
like watching us work on these old
pinball machines
you might like watching us work on old
buildings so go check that out
name of the channel is my brother donnie
here on youtube the link's down below
so we'll see you on the next one