Thank you to everyone who has been supporting our channel! If you use the link below before you purchase anything on Amazon, we get a royalty for sending you there, thank you!
Our store is located at 139 Caldwell St., Rock Hill, SC 29730.
ladies and gentlemen this is joe's
classic video games back with another
cool pinball repair video for you this
evening we are working on this bali six
million dollar man pinball machine for a
customer
and on the previous video uh we kind of
showed the condition that it was in and
worked on the power rectifier board and
the transformer was in pretty rough
shape
and we replaced a bunch of wiring
or connectors i should say
and worked on it we've replaced even the
actual rectifier board and made it do
its thing and we now have the
uh some
good voltages coming out of that that
seems to be rock steady and everything's
cool
but now we're going to move up here to
the solenoid driver board which appears
to be working but it's uh
we're trying to make this solid for the
guy settle it'll last a while for him
and then ultimately we're going to get
over here to this mpu board which is
actually a newer model replacement one
but it's not booting
so that's that's what we're working with
today now on the previous video i just
noticed um we had a bunch of the general
illumination lights that were out these
worked over here you see the one
flickering but this whole side didn't
work but now it is so i don't know maybe
we fixed that whenever we worked on the
connectors
but we'll get into that
so next up we're going to take this
solenoid driver board it's working
properly it's got the right voltages and
all of that but we're going to take it
out and service it a little bit just to
make it a little more reliable long-term
hopefully
so i'm gonna take that out with a
screwdriver we'll put it on the bench
and check it out
i'm trying to work on this board
and all matt wants to do is talk about
michael jordan
yeah
so here's our board i have a paintbrush
because i'm going to take off the dust
it's like magic
matt somebody in one of the videos today
said you seem like a cool guy
i i informed them that you were not a
cool guy because i feel sorry for them
[Laughter]
all right folks so we're going to clean
off the dust a little bit
you know i've been doing this more and
all more than i used to matt i like
being able to see everything and see if
it looks all screwed up i don't go over
to over the line you know that'll go
crazy with it you like to be able to
actually read the labels yeah you know
okay folks so
i've done about 30 videos on these
solenoid driver boards okay so you
should already know how to do them but
you might be a new person and if you are
or did you come to the right video so
here's the deal
matt
what is this
well it sounds like a solenoid driver
board solenoid driver board
this board
the bottom half of it
controls all of the solenoids in the
game so the computer
the mpu sends a signal through this
connector to this decoder chip to these
little chips that turn on one of these
transistors
right the transistors on the other end
of the transistor
through the wiring
on the other end of the transistor there
is a coil and the coil always has power
to it
whenever the computer uses these chips
to ground
this transistor it sends ground through
the you know it connects ground to the
tran the coil which makes the coil pull
in that's called low side switching
see we're trying to keep this for the
beginners man you're not supposed to go
oh i'm an engineer i know all about that
i learned that in school
makes it easy when you're searching
terms on the low side switching so it
switches things on on the low side
instead of switching the power right
okay and now somebody was asking me why
don't they just hook up the cpu directly
to the transistors that would probably
work once yeah it would work but you're
then once you so once this sinks to
ground you're basically running the
voltage
that's at the coil to it
which is like
43 volts
well the other thing too is those
transistors those are those are
transistors right not mosfets i assume
uh good question they're tip 102s all
right that sounds like that sounds like
transistors
so yeah those things require a lot of
current to drive yeah and your cpu can
maybe drive like 60 milliamps so if you
get a coil that screws up on the play
field it also will screw up the
associated transistor on this board
so if this board has been in another
game and let's say that the
let's say that the uh
the
one of the coils burn up so maybe it's
the left pop bumper that doesn't always
blow the fuse
sometimes it will sometimes it will just
burn up the transistor and burn up the
coil
and then there's a dead short there but
the game will still play
i don't know how you'd think that it
would blow the fuse maybe it does blow
the fuse i don't know but uh well
those it could be running at the right
current but those transistors just
aren't rated for continuous
use yeah it could be probably only rated
for like 10 on 20 on yeah
so you got to go through and check all
of these
to make sure all your coils are going to
work so that's the bottom half of the
board
this part of the board is a 5 volt
voltage regulator so it has 12 volts
that comes in it's really like 13 or 14
usually and it
this this
technical term is 12-ish 12-ish yeah
this transistor this bottle cap
transistor on this big heatsink turns it
into five
okay and this is a filter cap for it
to get all of the waves out of it
and then the
the uh
this this area here is the high voltage
for the
displays so it takes like 250 volts dc
something like that and there is a
little potentiometer in here where you
can adjust it
and you can set it between 170 and 190
something like that i think in the
manual it says to do 180 but a lot of
people run it like 170 it makes the
displays just slightly dimmer you can't
even hardly tell but it makes them last
longer just because you're not juicing
them so much they're plasma displays
so matt what what game does this go in
well
it sounds like it goes into pretty much
any valley game yep
so if you have a valley
from 77 to about 83 basically any of the
old valleys this will fit in it they're
all the same they look a little
different sometimes they're set up just
a little bit different but they'll all
work
okay and they will also work in all of
the stern games
so if you're watching this video you
don't you don't have to have a bali six
million dollar man what other games
could they have man let's see if matt
knows any other valley uh pinball
machines
i see i don't pinball machines i don't
want to say keep up with the brand
night raider is that a belly
yes but no but it's a oh yeah there is a
solid-state version yeah so if you had a
bally knight rider this board will go in
what other ones matt
well he said stern so i guess the stern
star wars
the old one
no no all right too old
yeah no too new no the old one
that's not stern that's uh that easy
now they know we've got a daddy start
star wars that we want to make okay
oh man i might cut that out okay so if
you've got it like a bally
uh
matahari this will go in if you've got a
bali kiss pinball machine this goes in
it if you've got a bali uh
we're putting in a six million dollar
man if you've got a supersonic this will
go in it if you've got a
evil knievel this will go in it uh if
you've got a bali eight ball this will
go in any of those early valleys this is
the one so if you've if you've got a
machine that's bali everything we're
doing of this 6 million man you can do
the exact same thing to your machine it
will literally be
exact inside
even the wires go to the same place
and the reason i did that was because
that's the smart way to design it they
just changed the art and how it looks
and you know as the customer you never
see any of this stuff so you don't care
if like
mata hari and kiss have the same
solenoid board you never even know
and it doesn't it wouldn't change it
wouldn't hurt the gameplay anyway
so my whole point is
yes this is for a 6 million man but it's
and we've done about 10 of them on 10
different games any of those the same
thing applies it works the exact same
they've been giving me hell matt about
the star ground
wiring
a star ground you know i don't
understand that yeah i know in the audio
circuits that's a generally a good idea
but what
so basically
they send the grounds up on some wires
and we have problems where the games
will reset and stuff because
they they end up getting resistance in
the wires or the connectors or whatever
so one of the mods that people do on
these solenoid driver boards is they tie
all the grounds together
so like this ground for the voltage
regulator
doesn't connect to this ground
right that's a safety thing
you think so
well that way if the hot from your 43
volts goes to your five volts it won't
conduct because the grounds are separate
and when i say safety i mean the machine
safety it's safe for you either way
i'm trying to think if that's right or
not
so
okay
so there's no 43 on this though so but
let's use this for example so this is
250 volts this is five volts okay the
high voltage i thought that you said
that okay the high voltage so 250 volts
over here right it needs to have a sp
as a separate ground
right from this one here
it's a good idea for a safety standpoint
that way but they go off the board and
they
connect the ground off the board
also they all they all go back to the
same ground yeah
they just have different long ass wires
that go to this one and this one oh yeah
then it doesn't matter
well they're telling me it does they
said exactly what you said see
so they're as uninformed as you are
no is it a safety thing i don't think i
don't think it matters well i'm thinking
of like i think actually
i'm improving the safety is it going
through a transformer because that's the
only time it would matter it's coming
from a transformer
and is the transformer grounded on the
secondary side or the primary side uh
the secondary side
then yeah it's ground on the secondary
side that doesn't matter
yeah see so the whole thing is the
ground from this runs through a wire on
one little pin over here
all the way back over to the transformer
and then there's a separate ground from
this that runs through a separate pin
all the way back to the transformer and
they're attached at the same place on
the transformer so one thing that we do
is we tie this ground to this ground to
this ground so that everything's
you're basically everything's grounded
to a plane instead of grounded back to
like one little point through one little
connector
that's the theory behind it at least
because the problem that you run into is
sometimes if you're
if you've got
because they're separate boards right
right so you run into a problem where if
the ground on this board is point two
it's not at this it's not really at the
same
uh
level you know what i mean right so
you'll get back flows and all that you
get you get crap where like coils lock
on and
stuff like that
right if the ground's not the same level
you have current going directions you
don't want it to go yeah it's a it's a
real problem in the gottlieb games
but see they give me crap because i say
got lib too they say it's got lieb
yeah but so really it's just people
giving me crap is what it is you know
well that's a german name right
i don't know i don't know the guy it was
assuming it's a german i don't know him
we don't bother pronouncing german
things right
that's a good point yeah we get a lot of
german people watching matt you're
insulting the germans
i mean we say we love the germans matt
might not but he's a jerk we say
volkswagen all right
not that volkswagen nonsense
that's true too that's true okay people
we'll get off of that all right so we're
going to do a few little mods of this um
because i like tying the grounds
together
other people may not
but i do and it's worked pretty well for
me
i had a guy give him a hell about it and
he said
he said uh
basically what you said that is an audio
it's a thing that they do in audio
circuits not sure how important it is in
pinball machines and i was like if there
was only somebody that's done hundreds
of them that we could ask
that could tell you
what you should do in a pimble [ __ ] but
they don't consider me an expert
i'm not saying i know but more than
anybody else i'm just saying i've done
it and it works works good
yep
that's all i know
and the only reason i even know anything
about the audio stuff because i hear
that's what you do when you're trying to
get the hum out when you've got like a
bad hum yeah like that record player you
tried to uh
hock off on me you gotta i'll tell i'll
tell you about that after he leaves yeah
all right so uh first thing we'll do is
we'll clean it up a little bit and then
we're gonna replace this filter cap
because it's got to go
okay folks so that's the first thing we
do we replace the filter capacitor
that's what you want to do on yours
so it is this original one at least on
this one is an 11 000 uf
capacitor
20 volts dc
um i think you mean
hey
no comments from the peanut gallery so i
replaced it with a 15 000 uf 25 volt now
thousand instead of eleven thousand matt
is that gonna work
filter capacity
probably because that's a
probably a 25
tolerance on that anyway
and i don't feel like doing the math but
that's pretty close
it'd be uh uh
thirteen five
so twenty-five percent right
thirteen six hey yeah but that one might
be twenty-five percent higher that one
might be 25 lower it's close enough so
i'm saying their tolerances are that's
full of crap it's a filter cap matt you
can go up a little bit if it's a filter
circuit come on now you know that i'm
saying electrolytics have crap tolerance
so it doesn't you can throw just about
anything
all right folks so you you the 11
anything from 11 000 to about 15 000 is
just fine on some of these from what i
understand i may be wrong but for what i
understand
on some of the games that had like four
flippers or something they went with a
higher one anyway
so uh
you know it it became a problem years
later on games like um
i don't i don't completely know the
circuit but on games like the twilight
zone it had all kinds of crap on it had
like four flippers and magnets and all
kinds of stuff because it was awesome
one of the coolest games ever it was the
one that had the ceramic ball didn't it
yeah
and so it just was loaded right but it
had this thing where if you hit both
flippers at the same time sometimes it
would make the game reset because the
power supply just couldn't handle it
once it got weak right no bueno yeah
yeah so
that's a thing
so you can go 11 000 to 15 000 on that
cap and you'll be just fine now i may
not know why
but i've done it on like a bunch of them
and it's just fine
so go ahead folks so if you're if you
try to buy one of these sometimes you'll
find that these are really
expensive so like an 11 000 20 volt
you'll be oh man they want 35 dollars
for that cap but then they've got a 12
000
20 volt and it's only eight dollars or
something you know so
you can you can fudge that one a little
bit and you can go up on the voltage a
little bit too yeah yeah you run a 25
volt that's fine yeah you can go up on
the voltage too so that's no problem
it's no problem so that's the first
thing you want to do now the next thing
you want to do is go on the back and
we're going to re-solder all of the
connectors around the edge because they
get bad solder joints
they gave me hell about oh i talked to
you about that before they gave me hell
about saying solder
yeah god what the
s-o-d-d-e-r solder exactly
they probably use a different product
wherever they're at and it's pronounced
solder
okay so
sometimes on these pins especially the
ones on the end you'll get broken solder
joints now i don't see any
at the moment because these have been
re-soldered here this will give you a
good example
okay see these last two pins here
see the shiny stuff around them
that's flux because someone has
re-soldered them before now see these
ones in the middle how they're not like
that that's the original solder
and then down here at the end it's shiny
again because they've resoldered that
now why are now why did somebody
resolder just the end ones it's because
they probably had bad solder they
probably yeah and the reason for that is
whenever you pull off the connector
so let's say you've got this connector
under you pull it off well you never
pull it straight up you're always
pulling it to one side if you're
left-handed
or maybe this side if you're
right-handed and what happens is when
you get the plug up the last pin or the
last couple of them get bent a little
bit and so they just get
banged around
and it literally will break it loose
from the board
sometimes if you look at it you'll see
that they're curved
oh that's how the last pin is
curved that one
it's just bent because of how it was
pulled off i may have just done it or
somebody else may have done it see how
the hen ones are messed up
so it's just a thing so the ones on the
end are always the worst but i always
just re-solder all of them but i i i
would say i've never seen bad solder
joint like right in the middle of the
connector it's always
sometimes it'll be two or three of them
on the end but
it's always the high current stuff too
yeah
sometimes that will do it on its own
probably without even removing the
connector there's yeah it sounds fake
but you high current connections will
lose solder everything
yeah it like transplants it somehow i
heard about that yep it sounds fake but
it'll do it that's why i believe in
divining rods
what do they call that whenever you use
you go with the rods to find where the
water is on the ground that's dividing
rods
you have to go ahead matt you're gonna
have to make some connections here i'm
not following go ahead matt
you said that the the the uh
that solder disappears from the joint
and moves down the wire and you said it
sounds fake and they can't prove it but
it happened i know i didn't say they
couldn't prove it i said it sounds fake
what you meant though that they couldn't
prove no they there's now talk about
divining there's papers out there you
can go look them up talk about divining
rods you don't believe in it do you i
know you're a fool matt you're a fool
i've seen people do it you go you go out
with the rods and you hold them like
this and when they cross there's water
there they've done tests man have you
never seen that no go on youtube they've
done tests
it works it doesn't always work
but on average it works
i'll take your word for it it's the
truth everybody knows put down in the
comments that matt doesn't know what
he's talking about and that divining
rods is a true witchcraft that works
well the solder transmigration you can
look at papers for that scientific paper
well i could write a paper about
divining rods
you get it in scientific journal they
call it witching okay witching water
you say so buddy
everybody knows you can which water
okay so uh i'm gonna re-solder all these
especially the ones on the corners
uh and then that's the next step you
want to do on yours okay so that's how
you want them to look so matt's still
talking about this witching water thing
he said
that myth but mythbusters did it
and now tell them what you said now how
did they do it
so they had pipes under
plywood plywood and and they they some
pipes have water some pipes didn't and
they tried to witch it with the sticks
and they couldn't do it and then they
got an expert to come in and could the
expert do it
i said not reliable not reliably but he
could do it
right
everybody knows witch and water ain't
completely reliable i'm just saying that
it does work okay so he did find the
water it just wasn't reliable
right and you're complaining that
whenever they tried it
what happened when
the mythbusters guys tried it that's why
when they tried it first they tried to
do it just based off their
impression from movies and whatnot and
they couldn't do it they couldn't do it
but the guy the expert did it and then
they tried to expert try to tutor them
how to do it but they still never could
do it that's because they don't have the
the the shine
that's sure
[Laughter]
all right
so
he tried to teach them and they they
weren't able to do it right
but he was able to do it
not reliably wait matt
this is a yes or no question
was he able to find the water with
pieces of stick or bars that he held in
his hand and which the water
sometimes okay there we go people there
we go all right so
we've resoldered all that after i'm
about to finish it up i was laughing at
matt so hard
so that's the next thing you want to do
now here's a couple of the mods that we
do that
people were telling us you shouldn't do
we're going to tie the ground on this
cap which is in the high voltage area
this little
here right the ground of that cap
to the ground of the uh of the five volt
which is this trace that goes all the
way around the edge of the board
all right
so and if you notice here it the screws
that hold the board in place actually
hold that ground to the
the ground plane there's a big piece of
metal on the back box
it's foil actually
so we're going to connect that to this
trace the way i'm going to do that we'll
scratch a little of the the
coating off of this trace and then put a
little jumper wire so that's the first
little ground upgrade we're going to do
what this will do is
this
this ground
is on this little trace that's the only
thing it connects to
and it goes back well connects there too
oh that's the that's a resistor on the
high voltage it goes all the way back
to this one little pin
and then out of wire all the way back to
the transformer
and connects to the rectifier board
where it's connected to all the other
grounds so we're just you know if that
if that ground gets screwed up you get
ripples in your
displays and stuff we're just going to
connect the ground from here to here
which will mean that instead of the
ground only having that path back to the
transistor i mean the the transformer
now it's also connecting through the
ground plane where everything in the
entire back box is grounded to the
rectifier board do you think that's
solid science there matt is that going
to burn something up i'm not saying it's
a great idea but that's what they did so
might as well leave it that way i i went
and showed matt how all the grounds are
connected at the tren at the transformer
he didn't think that it should be like
that but that's how they designed it
like i said if that's how they designed
it i'd leave it that way now what would
happen if the ground
on the displays
through that one little
pin
was to get screwed up where it's got 10
ohms of resistance on the connector
it depends but
the short answer is it wouldn't work
okay so if i tie that ground to there
it makes it more reliable right yep
well there we go that's all i'm trying
to do i'm just trying to make it more
reliable i didn't come up with this by
the way this is all from clay everybody
if you want to get mad at somebody get
mad at clay he came up with it i just
started doing it because he does it at
penrepair.com and it's worked great on
all kinds of machines so it's awesome
the way to go folks
okay so we're going to put this little
jumper from here to this ground trace
let me show you what that looks like
so there's my little jumper people
simple as that now that uh one of the
other ones you do
this is the ground
trace for the 5 volt filter cap
same problem it runs through one little
pin so if you get resistance on that pin
it gives you trouble
so when you just tie it to the board
there's a ground trace that runs right
here under it right see how
yeah so you got a ground running down
run into everything blah blah blah blah
run it over here
run into all of this okay
so we're tying that together
by just putting a little jumper
oh you gotta
easy peasy
okay and you can tell the ground on the
front because the other one's marked
positive
okay so there's one other one that we do
that's kind of minor
we're basically
there is a five volts that the board
makes here and then it sends off the
board
through a little jumper wire and then
back onto the board
across the jumper wire that sends five
volts to power these
four chips
so without that five volt
these four chips can't work right
and so there's a little jumper you can
put on the back so that it doesn't have
to send it out of the connector and then
back into the connector
you may have some resistance on the
connectors you just jump across the
board so it's you're like adding a trace
basically on the board that they didn't
add right
and so the way that you do that is you
tie taps test point one and test point
three together
so we're just going to put a little
jumper between those two test points
and so
here's test point one it's the five
volts going off the board
right
and then test point three is here it's
the five volts coming back on the board
and if you notice it's the last pin on
the connector
so it's the one that gets screwed up
with bad solder
uh
which
is one of the reasons that you want that
little jumper it just makes a better
connection simple things you don't have
to do any of these this is just how we
do it people always ask us how we do it
this is how we do it okay so i'm gonna
put a jumper between test point one and
test point three
so that the five volts doesn't have to
go off the board and then back on the
board to get to these chips it just
jumps right to these chips
okay there's our little jumper wire make
sure you don't put it on the wrong one
people
uh and um
next thing that i did
this is the potentiometer to set the
voltage
on the high voltage here
i replaced it and the reason i replaced
it is because these ones are known for
going bad and so
what usually will happen is you just
won't have any displays because this
will be open
right so
these little
thumbwheel pots
just get a bunch of carbon and dirt and
stuff in it they stopped working so i
put a new one
i wish you could still get this type i
can't ever find this type so i always
have to use these little cheapo things
but whatever
this one you can adjust with your hand
that one you have to use a little
screwdriver which i guess is best anyway
okay so uh swap that and then i tested
all of the transistors
the voltage regulator and the uh
this one here
and oh and these and everything was cool
so you know basically like you test the
transistor with your diode check you
want to go through and just check all of
them while you have the board out see if
you see find anything shorted
okay so everything checked out good so
uh um we're pretty much to the point
where we're going to put it back in the
game
haven't found any real problems on it
like i said it was already working
everything was cool you can replace this
cap too which is the filter capacitor
for the displays
if you do get a lot of rippling in your
displays it could be that or the ground
um
everything seems pretty cool the fuse
was not blown
you saw the displays looks appeared to
have the high voltage anyway on the
previous video i guess
i clean the
connector pins you literally can use
like light sandpaper or
a little file or whatever you want to
clean these some people don't like doing
that they'd rather use a chemical you
can use that too if you know of a
chemical that'll clean them up better
than a sandpaper or a file
i think people
buy a lot of deoxit
to do that
but we're pretty much ready to put it
back in
we'll adjust our voltage for the
displays and we'll see how close to 5
volts we are on the previous video i
mean on the previous machine or one of
the previous machines whenever we were
working on that flight 2000
we figured out that um
these two capacities two resistors over
here
which are r 50 and r
49
uh are used with the this is usually an
lm323
they are used to because that's an
adjustable
voltage regulator
to adjust the five volts out those two
resistors are basically raising that a
little bit so that instead of outputting
five volts it's outputting like 5.2 or
something like that
uh but then once we have
higher line voltage feeding it in it
seems like so the 11 not the 12 not
being 12 being more like 14
you end up with with your five is too
high it'll be like 5.4 5.5 so we figured
out that you can cut one of those
resistors out
one or the other i'd have to look on the
schematics again
and it will lower that voltage back down
on a lot of these they have had the
lm323 replaced
at some point so this one is a
78h05 so it's 7805 but it's the h
variety which is the 5 amp version the
lm323 is 3 amp
a regular 7805 though is only 1 amp so
[Music]
it doesn't look like it's ever been
replaced though but it may have been in
antiquity
is that solder from 1980 or from 1982
who knows
okay
but that's been replaced at some point
um
so it doesn't really cost a lot of money
to service one of these you definitely
want to replace the filter capacitor
you probably want to replace that
potentiometer
right
but
you see i didn't replace anything else
because it's all still working it's
pretty decent design so
no big deal all right so we're gonna pop
it back in the machine and see how close
to five our five volts is and then see
if we can adjust our high voltage to 180
or so
okay folks so here is the schematic
and this is for specifically 6 million
round now i don't know if that board
actually was originally in this or if
it's been switched out but
here is what that 5 volt voltage
regulator is listed as national lm323 or
fairchild 78h05
so someone was telling me and they may
be correct i don't know they were saying
that the 323 is an adjustable
regulator
5 volt regulator and you adjust it with
the the two resistors i'll show you here
in a minute and but the 7805
is not it's just a it doesn't need the
resistors okay so let me show you the
the schematic but i'm just showing you
this to show
that from the factory they were putting
those 78 ho5s in it so the theory we
were thinking was that it was supposed
to be a 323 but that somebody had
replaced it with the 78 h05 at some
point
but didn't update the resistors and that
was the whole problem um
because the the voltage is the output's
too high on the solenoid board so let me
show you the schematic okay folks so
here is the schematic
we are supposed to be getting 11.9 volts
in
right
and there's the ground that we were
talking about
okay and then it runs through an 11
7
cap
okay now i changed that to 15. the one i
was in it was 11. i wonder if that would
that raise the output
15 to 11 uh
11 to 15 000
[Music]
micro farad that wouldn't really change
that's on the input side yeah it's on
the input side okay so they run it into
this voltage regulator that is either a
323 or a 7805
okay
12 volts going in
but look they don't have it tied to
ground they have a resistor there 2.2
ohm resistor they have a 4.7 ohm
resistor if it's on a stern one the
stern ones are have ripped off the same
design and then they have this resistor
here this r49 tying the output to the i
guess that's the base
and that one and that basically raises
the output it's not five it's at 5.4 but
they've done it on purpose
but the the whole problem is it looks
like originally
since you're getting 11.9 in that little
thing would raise it up to like 5.2 so
that they could
tolerate like some voltage drop in the
wires
but the problem is
we're getting like 14 in
i don't know that that would necessarily
be a problem but since they have this
now we're up to like
5.4 which is way over
tolerance on the chips you know
and that they must be burning a lot of
heat for that to be a half watt resistor
there
yeah so
um here's how we fixed it on the last
one we just removed that resistor we
took r49 out you just cut it out and it
drops the
your 5.4 about 0.2 200
millivolts
so it'll drop that sucker to about 5.2
if you cut out r49 and you kind of need
to do it because it's
5.4 right now you shouldn't be running
the board
you shouldn't be running chips at 5.4 i
mean that's starting to get
out of line yeah
and people were suggesting that you
could also do it by
jumping over this r50
just jumping that straight to ground
if it's 7805 you normally would put it
right the ground yeah
so that it's just weird so
so uh
people have pointed out that for a 323
that would be a good idea but as you
just saw on the on the on the schematics
from the factory they're putting 7805s
in there where you're supposed to put it
straight to ground but it's not made
like that
so
i'm going to clip out r49 but let me
show you what it's doing in the cabinet
okay so first we're going to check the
voltage
for the displays
so that you got to be careful when you
do this that's why that plastic sheet is
on there they don't want you getting
shocked because it's got about 250 volts
running through it
let me paul at it
so one of the test points will give you
the input voltage
good god i got the shakes tonight i'm
gonna get killed
man if i get killed call the police
255 coming in
[Music]
i'll make sure to record it
179 going out that's about where i want
it so we're good with that okay all
right um and so now we're going to check
the five so we've got
[Music]
hell
trying to be careful
15.2 coming in
this is supposed to be 11.9 we're up to
15.2 but that's pretty common like it
it's just what it does because you've
got a higher line voltage and you would
think that the transformer
a higher line voltage transformer would
have a higher output but then they're
rectifying it on the board and it's
still high as well 15.2 that's probably
that's unregulated yeah it's unregulated
so
but it's you saw in the schematics it's
supposed to be 11.9 so it's 15.2 i don't
know
i don't know if that has anything to do
with
um with this but we've got 5.39 going
out that's just too high man it doesn't
need to be that high
um
so 5.39 going out i'm going to just
remove that one resistor
and then we'll recheck it and see if
that drops it
okay so i simply cut out r49 completely
removed
okay
now
we got our 15.4 coming in
and going out we have 5.09
perfect it's exactly where you want it
so
it's five and a little high
for if there's any loss in the wires or
the connectors or whatever but now
you're not sending
crazy voltage to the thing so i've been
doing that on the last couple machines
because i saw somebody talking about it
on pin side i never realized that uh
the the output was that high that that's
crazy
[Music]
crazy man so you might want to do that
on your machine if the five is really
high
what do you think
close to five is good yep close to five
is good but a little higher than five
but that's ridiculous yeah yeah so i
don't i don't i don't know why they did
that
[Music]
it would be interesting to see if if you
actually had 11.9 going in
is it a thing well it's rectified though
you wouldn't think that it would do that
is it a thing that transformers the
voltage
creeps up over time
output voltage no not that i've used to
come across
um
maybe they were never 11.9
i mean there's some of those metal case
transistors sometimes sometimes they'll
uh
slowly leak up over time that's what
kills the commodores
so like that 70 that five volt regulator
might
one day in its life become a seven volt
regulator
okay well maybe that's it but that's on
the output not the input yeah
i don't know all right so that's how you
fix that though okay so uh i'm gonna
turn it back off we'll plug in this
board just so i can show you the um
what the mpu is doing that's going to be
what we tackle next but uh
i think our rectifier board and our
solenoid driver board are good to go now
okay so if you plug in the board you the
lights are just locked on so it's not
booting and that will be our next thing
that we work with now matt looked up the
um data sheet on a 7805 and
that 78 h05 in that
package i looked up the fairchild
data sheet for that vintage yeah
and you can run
40 freaking volts into it and it will
still make it 5 volt output that's right
so it shouldn't really matter what's
coming in even though it's way high so i
don't know
it's strange
maybe maybe at the time they wanted 5.4
volts going to it i don't know
i couldn't tell you i don't know and
then he was mentioning the uh
uh
we think the 15 is high but see
i don't know whatever
whatever now the way that they do it
down here is with a bridge rectifier
right well so if you've got a high
voltage going into a bridge
if it's too high going in it would come
out too high yeah the bridge doesn't do
anything other than just change the
polarity yeah it doesn't it doesn't
affect it at all yeah so uh that would
explain why it's too high and then matt
was mentioning like i thought too
the voltage coming out of the wall is
like
a lot higher than it used to be
and here in our shop it's high as l yeah
it used to be 110 115 now it's like 120
um
[Music]
so whatever
okay so
got our voltages looking good we're on
to the mpu we'll do that on the next
video matt
tell him what to do
see if matt knows what to do wow i mean
yeah you always subscribe of course yeah
always subscribe of course yeah unless
you already were unless you already were
and then don't hit subscribe damn it
it'll unsubscribe you all right don't do
it people only the buttons written only
if the button's red yeah or now they
might change that matt
okay don't mat if you're subscribed
don't mess with the subscribe button
i mean you always like it
you like the video leave your comments
down below especially if they're
positive i don't like negative comments
everybody knows that i'm very negative
about negative comments leave the
negative comments they're entertaining
don't do it okay and uh
make sure to uh check out my brother
donny you didn't tell him about that oh
yes
yes brother donny down in jefferson with
his old buildings yep
matt's been down there visited my
brother donny they got in an argument
he's as crazy as he says yep
um you were supposed to buy uh something
from them and you didn't buy it
oh yeah that railroad cart
no there's something like trash laying
there or something
there was a roll of plastic or something
and matt was like what are you gonna do
with that blasting donnie was like i'll
take 20 bucks
you want it you're going to get it and
that was like well i might
so check out my brother donnie here on
youtube he's literally my brother if you
like watching us work on these old
pinball machines you probably enjoy
watching us work on old buildings there
are we have a couple old buildings in
beautiful downtown jefferson it's coming
a long way matt i know y'all matt's
always down on jefferson because he he's
had family down there for a long time so
he remembers whenever it was like
there was no uh
industry in jefferson but there are two
or three stores open now matt
so 200 angry exactly so
matt's always talking well he doesn't
say nothing negative about jefferson but
he doesn't see the vision like i see it
but if you uh if you enjoy watching this
work on these you'd probably enjoy
watching his channel he's pretty crazy
uh so we appreciate that make sure to
leave your comments below give us a
thumbs up and check out our parts page
too go to lionsarcade.com we have a page
at the top of our website now a parts
page matt's been on there buying all of
our parts i bought your solder sucker
yep bought our solder sucker now the uh
it's not used vintage parts it's just
little stuff that we use in our in our
repairs so you know we've got like a you
know a solder sucker i think there's a
fluke multimeter on there little side
cutters
yeah little stuff like that we just got
links to stuff like that it takes a lot
of that stuff oh our t-shirts are on
there
you bought a t-shirt oh yeah yeah so
our t-shirts are on there but uh some of
that stuff it takes you to amazon and if
you go to amazon and buy anything after
you click that link it gives us a tip
for sending you to amazon so you can buy
a car
or uh what did you buy on there
well i bought the solder sucker and i
bought some extra solder
oh okay yeah so any anything you buy on
there gives us a tip so we appreciate
that
but i hope you enjoyed the video we're
just having fun hanging out working on
this solenoid board it's a little bit
farther next time we'll get work on the
mpu and that will fix it and get it back
up and running
there you go that's how that works man
that will fix it
it's not going to run with the mpu with
the lights lock the one it's supposed to
they come on and blink
right sadder stuck on yeah
that yeah that's stuck there's a problem
that means no working we're gonna have
to fix it so
stay tuned next video up we will fix the
mpu and that will fix the game i promise
we'll see you on the next video