New Feet for an Old Table

Thomas Johnson Antique Furniture Restoration
41 followers
111 Video Views·Feb 9, 2025
Tom Johnson of Thomas Johnson Antique Furniture Restoration in Gorham, Maine adds custom-made reproduction feet to this antique table. Tom has been restoring furniture professionally since 1979. Visit our website at http://www.thomasjohnsonrestoration.com, or write us at [email protected]. And for those on the east coast looking for custom framing, be sure to check out Tom's daughter's shop, https://www.emcollier.com (@emcollierframes on Instagram).
I'm Tom Johnson Thomas Johnson antique
furniture restoration in gorm
Maine well we're really busy
here nice to spend some time out in the
snow the third floor renovation is
coming along really
well and soon we will begin the shop
transformation and I will be showing
that on video but you know this is a
great time I'm really
enjoying looking back at our previously
published videos you know over the years
a lot of people have asked for more
details and specifically details about
my thought process and that's what this
video shows I'm making new legs for a
table as I work on the legs I'm really
getting into the to the design and
learning design as I draw the legs I
feel like I'm getting into the head of
the original designers and then with
some Clues from photos on the internet I
was able to bring those feet in and I
felt like I really was able to get into
that original design so this video shows
the making of the feet and great detail
and the finishing of the feet and the
color work also in
detail so enjoy the video uh subscribe
like share I appreciate
it this is a video about raising the
height of this beautiful uh dining table
we need to raise it 2 and 1/2 in because
the uh chairs hit the apron 2 and 1/2 in
is a lot but it's because we've removed
these casters they are already removed
these casters don't look good and they
just can't take the weight of this table
and just serve the dam damage the floor
so we're going to do away with the
casters okay first we got to deal with
these cracks I'll put a clamp on it see
if it
moves well I'm not seeing much movement
in these cracks at all so I'm going to
make some uh White Oak wedges
yeah the uh the rest of the cracks in
this section uh aren't wide enough to do
with a shim so I'll just use
putty if a crack's big enough I'll glue
a wedge in it otherwise putty
so I'm fam wooding up all the uh cracks
here but here's one big enough uh for
for wood for another wedge
so uh as you can see I've got putty all
over these legs I've got a lot of
sanding to do and while I'm sanding I'm
going to think about the little uh
additions we have to make here in fact I
may start by making a
drawing uh and then be playing with it
and thinking about it while I'm sanding
so I'm going to tape a piece of paper
here down to just a a board and I'm
going to trace the leg and then
straighten up that tracing it doesn't
the the my image of the leg doesn't have
to be exact but it'll give me enough
then to be able to draw uh the proposed
feet or extensions I should
say
for for
for
okay I think we have a fair uh
representation of the
leg we need to
add uh 2 and 5/8
in I know before I said 2 and 1/2 but I
forgot about the sleeves on the bottom
so it's
really too and
5/8 so we've got to fill this space
here so how am I going to design these
leg extensions uh first thing I'm going
to do is uh look up Bun feet
online this is Osborne wood products
they do a lot of great turnings uh you
can see all these variety of feet it's
amazing really good
ideas now why don't I buy feet from them
I would in a heartbeat if except all
these feet are absolutely huge they're
not made for furniture they're more for
uh kitchen islands and also although
they make them in Red Oak they make them
in four different Woods although they
make them in Red Oak that wouldn't work
for this but I am really liking this
foot right
here this foot these are the elements
that I just
drew damn near the right size
I think I'm going to draw this right
here so I know I want a 18 uh
pad on the
bottom don't know the diameter
yet and I want this to be a ring I want
this part to come to rest in a ring I
think I'll randomly make that A4 of an
inch there's one
quarter make it just a little bit
bigger and then I need
to I want to well I could go straight
into
to my foot maybe that's what I'll do so
I got to
decide the the length of this uh the the
actual bun if you want to call it
that maybe I'll make it like uh I'll
just try 1 and 1/2
in for openers
and then
how how wide should it
be I think I'll make
it the same uh diameter as this main
readed leg
and so then I want a little uh a 1/8
cap on that
bun I'll make this this 2 in wide and
and make the same for that little bottom
disc I put on
there and then I think I can just go
with a Cove and not not like
perfectly centered
but oh I see yeah it it is centered but
it's
all right
yeah I'm liking this it definitely goes
with the rest of it it definitely looks
like it could belong
there so I need to send a I'm going to
photograph this and send it to the
owners of the table to uh get their
approval and meantime this gives me
enough information that I can start
gluing up the wood I need to make the
turnings so I need six blocks of wood uh
4 in square about 7 or 8 in
Long actually two of those could be
smaller but for the purposes now I'll
just keep them all the larger size
a
okay
if this joint uh fails it won't be for
lack of glue
you
you
oh
you know I usually uh turn spindles and
such from the square but these are so
big I think I'm going to
cut them again and make them octogonal
a
I realized I needed to make one the ne
size up you that that wasn't really
going to work this is better
so
that's the first one you know it always
takes much longer to do the first one
you're sort of figuring out which tool
to use for which cut and stuff by the
time I get to the fourth one uh I'll be
able to do it pretty fast maybe I'll uh
even make a real time video of the last
one when
I know what I'm
doing I'm getting ready to turn uh the
last one and of course these last two
are smaller ones for the center legs so
this is the last one I'm not going to
show it in real time because most of the
time it's just hogging away excess wood
sh
so I'm all done making the feet four big
ones two small ones now to install the
uh new feet on the
legs yeah these legs they still have the
uh original sleeves in them uh for the
casters I've got to get those out
so that's a 3/8 hole pretty standard for
these uh sleeves and I've got to drill
it out to 5/8
a
on
yeah not
bad you know I'm a little concerned that
this might move on me under the stress
of drilling you know because of this
taper here it's not
clamped well I can't move it with my
hand but I'm going to add some uh
sandpaper to the bottom of this block
and I'm going to clamp it when I drill
it
there's also stuff on the bottom here
but might help to clean that
off that looks like it lines up pretty
well
well oh good that looks looks well
centered do you think they're the same
size
okay that looks good uh my biggest
concern was that this be centered
correctly on the existing turning
and yeah it looks great so now I'm going
to do the others uh off camera I'm do
this one and then turn it up see what it
looks like in the upright
position I think they look
good so the legs were always uh darker
than the table uh top even originally uh
I put a little paintner on them and they
look great I don't think they need to be
stained and then I think I have the
stain for the new turnings too for the
feet I tried some of the same stain that
I used on the
top and it's not bad at all but it's a
on the light
side so this is the same oil soluble D
stain I used on the
top and this is the standard Golden Oak
I'm applying which is too
light that's fine
and then I
applied same type of stain the oil
soluble Dy stain but this is the
Walnut now let me put some more paint
thinner on
that this just paint thinner but I'm
assuming that when I put a coat of
varnish on it that's what it's going to
look
like so this looks good but I might need
to mix up a stronger
solution I'll use 8 oz of paint
thinner 2 tbspoon of the powdered D
stain
so I've got to let this uh dissolve for
an
hour okay let's try it with the
stronger D stain now so this is paint
thinner on the leg presumably this is
what it's going to look like when I put
the varnish on
it and here's the Walnut
stain I better keep going with this and
do the whole
thing but I think that looks good and if
it needs to be adjusted in any way I'll
do that with color in the
Finish okay so uh I'll let these dry
overnight and uh then tomorrow I can put
a coat of clear finish on the legs and
the feet we'll see what they look like
and over the next few hours uh as this
dries I'll come back and and put even a
little more on especially on the feet
like this that um are a little bit
lighter
okay these have dried overnight and uh
time to put a coat of clear finish on
the entire leing foot if these feet are
too light I'll be very happy the worst
thing would be is if they're too dark I
can darken them up
okay I'll let these dry till tomorrow
these have dried overnight finish really
soaked in
but uh before I put on a second coat of
clear the feet uh some of the feet are
still a little bit on the light side so
I'm going to mix some uh clear varnish
I'm going to mix in some of the same
stain that I used uh and then brush that
coat on the feet see if I can make them
darker Bo it's a nice color I think I
can put even more stain
in well I love the color wonder if it's
dark
enough I'll try a little
bit it's definitely darker uh not really
sure if it's dark enough but I think I'm
going to go with that I can always do it
again yeah I think I'm going to go ahead
and use this color if it's uh it's
definitely in the right Direction then
I'll coat these with clear and if it uh
if it's not dark enough I imagine this
is going to need four coats this is just
a second coat so I can add it again to
the third coat even a fourth
coat you know when uh matching colors uh
people often think you mix up a
particular
stain uh put it on there and it's the
right color and that's rarely the case
typically you uh build your color in
layers just like this I stained the wood
now I've got stain in the finish one or
two coats then the clear the Finish
itself carries with it a really nice
amber color so you're building up the
color in
layers now I need to uh clear coat the
rest of these
legs all
right let them dry
overnight yeah these are dried overnight
and uh they look great uh you can feel
little knits here and there I'm going to
go over them with a scotch Sprite pad uh
just to smooth them out a bit and then
I'll put on a coat of satin which I'm
hoping will be the final coat
yeah the legs came out uh really well so
the uh next step is to uh assemble the
table so here it is the finished table
ready RAC and
height if you remember it had casters
they weren't working and it needed to be
a little higher anyway so I made these
new feet and uh I think they look pretty
good
