Early Cummins diesel engines Model F, Model P, Model U. 1919-1928

Machine Engine
3 followers
I know I know I was gonna try to premiere all of these around 8 PM. This one’s a little bit late early Cummins diesel engine episode.
We talk about the model C, which was essentially like a hit and miss engine ran off of oil
The model F, model P, and model U in this engine episode enjoy
I found a video of a model P running I’m going to link it here if you want to see it because they’re super rare. There’s only one left in the world.
#machine #engine
The year is 1928. Cummins would release their first ever four-cylinder diesel engine,
but it's important to note it wasn't their first diesel engine, but their first four-cylinder
engine. Cummins was founded back in 1919 by Klessie Cummins and financier William G. Irwin
in Columbus, Indiana. The first diesel engine the company would produce would look very similar to
a hit-and-miss engine, single cylinder, HVID under license, and it would be offered in 1.5, 3, 6,
and 8 horsepower configurations. They were used to run pumps and workshops, oftentimes being called
oil engines because they ran off of oil fuels such as diesel fuel and kerosene. These engines would
be marketed by Cummins as the Model C, though technically not your traditional diesel type
engine because of the way the fuel mixture entered the combustion chamber. In 1921,
Klessie Cummins would design and patent a direct injection design. Real quick, in a gasoline engine,
liquid fuel is pumped up to the carburetor, which mixes with air. The mixture gets distributed to
the cylinders from intake manifold, and then it goes into all the combustion chambers, ignited by
a spark plug when the piston is at the top of its stroke. It is a controlled explosion from the
igniting of the mixture that makes the piston go down and turn the crankshaft. Things are a little
bit different in a diesel engine. A diesel engine has to draw air into the cylinder, compressing
the air to increase its temperature. The fuel is then injected into the cylinder. The fuel combusts
at high temperature, forcing the piston down. But for it to work properly, a precise amount of fuel
needs to be injected into the cylinders at the right time. If the charge is too rich and not
timed properly, catastrophic things can happen. Klessie went through 3,000 different prototypes
in five years to try to get the right combustion to work, and what he came up with was mechanically
controlled direct injection. Cummins' first engine to be produced in a series was the Model F.
Not to get confused with the Model F that comes later, the original Model F came in 1924.
It could be had as a single cylinder or a twin, and they were big engines, and they were mostly
used for irrigation pumps, powering equipment, and as power plants on yachts and boats. It could either
be had in 178 cubic inch displacement, 2.92 liters, or as a twin, 356 cubic inch displacement,
5.83 liters. Displacement is calculated by bore times stroke times number of cylinders.
It could make 12.5 horsepower as a single or 25 horsepower as a twin at 600 RPM, and this is just
an estimate, 218 pound feet or 295 Newton meters around 300 RPM with a bore of 5.5 inches and a
stroke of 7.5 inches. Starting with a serial number of 8,000, it weighs 4,800 pounds in twin
form built of cast iron. There was a couple or at least one that was built of aluminum,
and it weighed 2,960 pounds. The next iteration of Cummins' diesel engine design was the Model P,
which apparently the internet doesn't know about because this engine came out one year before
the Model U. I'm not making excuses or anything. I'm just trying to be transparent. If you type
in search bar on Google, what was the first Cummins four-cylinder engine design? It says
the Model U, but the Model P predates it by one year. If you guys know of any other Cummins
engines that were four cylinders in configuration that came before the Model P, put it in the
comments section below. Anyway, the Model P could be had in either single, twin, all the way out to
six-cylinder configurations with the valves on the outside of the cylinder's external push rods.
Only 27 Model P's were ever produced, and they were mainly used as power generators. In 1928,
Cummins would introduce the Model U, which was totally enclosed diesel unit where the push rods
and valves were not exposed. Just like the previous engines, it could be had in single, all the way up
to six-cylinder configurations, all the cylinders placed in line formation. Klessy made some
improvements to the overall engine, which included, but not limited to, replace the needle injectors
with fixed displacement injectors for each cylinder, a plunger that was controlled by a gear
pump and distributor. Klessy would also make the combustion chambers high turbulence to better
mix injected fuel with compressed air, which boosted power and efficiency. The engine also had
fully pressurized oiling lubrication system, which at this point was cutting-edge technology. Most
engines still had splash lubricated, where the connecting rods would have a small hook and dip
down inside the oil in the oil pan and bring it up, splashing the cylinder walls and making it
drip down to all the key components. Full pressurized oiling lubrication gives a steady pressurized
stream of oil to all of the key components, such as connecting rod bearings, main bearings, camshaft
bearings, etc. The Model U could be had in many different cylinder configurations. As a single
cylinder configuration, 95 cubic inch displacement or 1.5 liters. As a twin, it would be 190 cubic
inch displacement, 3.11 liters. Four-cylinder, 381 cubic inch displacement, 6.2 liters.
And six-cylinder, 572 cubic inch displacement, 9.3 liters. It makes anywhere between 10 to 14
horsepower per cylinder up to 85 horsepower-ish on the six-cylinder, producing that power around
1,000 rpm. This is just an estimate. 446 pound-feet or 604 newton-meters around 500 rpm with a bore
of 4.5 inches and a stroke of six inches. This engine could get up to 35 miles to the gallon.
The four-cylinder model weighed 1,200 pounds. Klessie would convince his partner to buy a
Packard touring car to be the test mule. Klessie had no desire to build cars. The compact diesel
engine was his passion. Klessie would build a four-cylinder Model U and install it in the
engine bay of the Packard with just a few inches to spare. Just look at it. I mean, it's a huge
engine in that engine compartment. Once the engine was installed, Klessie would drive, not trailer,
he would drive the car 600 miles to New York City, New York to show the car at the 1930 New York Auto
Show. The engine worked flawlessly, burning 30 gallons of kerosene, getting around 20 miles to
the gallon, which is a pretty big number for this period in time. When Klessie got to the New York
Auto Show, he was unable to show the car because he did not register the car in advance. Klessie
was an outside-the-box thinker and he saw a place across the street with a for-rent sign in the
window and he would rent the space and display the car there with receipts and testimony that
the car only used $1.38 fuel for the 600-mile trip. Later that year, Klessie would drive the Cummins-powered
Packard to Daytona Beach, Florida, where Kane Don, who was a British racer, he would set a series of
land speed records with it. Klessie knew he had a winning concept with the diesel engine. He just
needed to get the press involved because they wasn't really selling all that well and Klessie
knew if Kane Don was at Daytona Beach, odds were connecting some dots, the press would be there too.
While at Daytona Beach, Florida, a new record for the flying mile was set at 80 miles per hour,
but what really got the press's attention was how efficient this new engine concept was. Klessie
drove the Packard from Indiana and used less than $4 in fuel for the 2,550-mile total trip.
The Model U would pave the way for the Model K, which would be a staple for Cummins, but as they
say, that is another engine episode for another day. Now it's time for Name That Tune. First person
to get both the name of the band slash artist and song title correctly in the comment section
will have their comment pinned to the top of it. If you found any value in what you just witnessed,
we have a playlist of Lost and Forgotten engines which I'll link in the description.
Until next time, I'll see you in the comment section. Toodaloo!
