"Complete #how to #guide for your VAG/VW/Audi/Porsche #VR6 3.6. These motors are essentially VAGs last cut at the VR6. With the larger displacement and GDI fuel injection, they are quite a package, but maintenance and tool free engines are key! Here is the play by play breakdown of the episode:
00:00 Project Intro 01:00 Grenaded Chains 01:52 Parts Acquired 05:34 Tools Required 06:18 Top Dead Centre the Motor 07:11 Verifying Cams are Phased 07:49 Oil Pump Installation 09:40 Lower Timing Chain Guide Installation 10:27 Oil Pump Sprocket Installation 11:11 Lower Timing Chain Installation 12:24 Lower Timing Chain Tensioner Installation 12:59 Pull the Pin! 13:02 Torquing down the Oil Pump Sprocket Bolt 13:53 Oil Check Valve in Block 14:27 High Pressure Fuel Pump Lobe Installation 15:20 Upper Timing Chain and Intermediate Guide Placement 15:54 Cam Control Box Installation 18:33 Intake Cam Phaser Variator Installation 19:35 Exhaust Cam Phaser Variator Installation 20:22 Upper Tensioner Guide Installation 20:48 Side Tensioner Installation 21:16 Checking with Rotating the Motor 23:52 Final Torque on Cam Phasers and Tensioner 25:17 Outro"
Hey guys, in today's episode we're going to be looking at doing the timing chains on this
VR6 3.6. This is the DLV motor or BHK motor specifically. They are found in the Volkswagen
Passat, Touareg, Q7 and the Porsche Cayenne and probably a couple other things I don't even know
about. So there's one or two reasons why you're in here. One, you're here to do some preventative
maintenance because you've got a little bit of chain rattle at startup. Perfect. Or you decided
to drop a 16 mil socket into the back of the cylinder head here the last time you were working
on it and didn't notice and grenaded the motor when you're redlining it. So if you're the latter
you probably have mismatched socks like me and you're human. So I'm going to show you what
happened and then we're going to look into some parts that I'm replacing while we're here and
get into the procedure. This is how I opened up the back of the motor. I finally found my 16 mil
socket in the middle of ground zero where the chain exploded. The guide obviously exploded. That
little pin right here is bent. The oil pump sprocket obviously shredded apart. It impacted the oil pump
itself a little bit just on the casing and then this guide took some impact as well.
So a decent amount of carnage caused a pile of oil or metal shavings to fall into the bottom
of the oil pan so I had to clean that out as well. Do an oil change as well and this also in turn
caused the valves to impact the top of the piston so bent a bunch of valves. Had to take the cylinder
head off, put a bunch of valves in, lap them and yeah a whole pile of destruction just along the
way. So word of advice, don't leave your tools in your engines. What you're going to want is a
timing chain kit. This site acquired from ECS and it came with essentially everything you need for
your timing chain kit for about $160. So it comes with your lower timing chain, your upper timing
chain, all your bolts for all your guides and it came with the fifth guide over here as well for
in between your camshafts there. So it comes with a guide tensioner combo unit, this is for the
lower chain and this has a step motor is what they call it. So if you take this that pin out
it comes out but it locks in place it won't go back. There's a little tab in there that you
press to release it and then you can recompress it to install in case you do that. This is for
your upper chain and this goes into the side of the head and this is just a spring loaded and
oil pressure fed for your tensioner for your upper chain. So that's a pretty nice inclusive kit
that you're going to want. There's obviously some sealants for your rear cover.
You're going to want to do a rear main seal most likely as well since that cover has got to come
off. I've got some head studs and some since I've got to take the head off to redo my valves but
then you've got some crank bolts as well for your flex plate and then your torque converter bolts
as well. One thing you want to consider replacing while you're in here is your oil pump sprocket
bolt. The earlier 3.6 motors had experienced a quality control issue with their bolts. I think
they're just using inferior or weak bolts. They're 8.8 grades. They upgraded it from the factory to
10.9 so you might as well do that at a minimum. Now mine, I've got to replace the entire sprocket
because I blew it up and so that led me to inspecting this case. This is something you
should at least do if you didn't explode your motor but you should check this out. The inner
board here has got some serious gulling going on and that is not a result of my stupidity of dropping
a socket into the motor. This is just wear and tear so good thing that I happened to catch it.
Something you guys should check as well. There's a little bit of wear on the
bore in the back here as well. You can see that it was starting to happen in the back as well so
something to look at. You can get a same style replacement if you want or what you can do is
what I'm doing is upgrade it to the, I think this is in 2011, they upgraded the entire pump assembly
so this sprocket is a nice one piece unit whereas this is a two piece by design.
So you see that they made together then bolt together whereas this is a nice one piece.
What's nice about the single piece is that, well it's got a stronger bolt. This bolt is an M12
whereas for this it's an M10. So we're going to an M12 bolt, stronger design, everything all around.
The problem is that this sprocket doesn't fit on this old pump. You need a new pump. You can see
the recess for the drive gear here is substantially larger than what it is on this older style pump.
So you'd see how big that difference is. So anyways, if you want to go to the single piece
sprocket you're going to need a whole new pump assembly. This one I bought brand new.
It also comes with a metal gasket on the back whereas removing this it didn't have that metal
gasket. So they've made a couple changes and something you guys are going to want to consider.
Do your bolt at least at a minimum and then check the condition of your inner
bores here and then consider going to the upgraded pump. These are the tools I've acquired for the
project. Pretty generic stuff. It's from eBay or Amazon. No brand, just 40 bucks. You get this
cam locking plate or bar, whatever you want to call it. You can make this almost yourself.
This is your high pressure fuel pump cam lobe locating plate. You can probably do away without
it. It just came as a kit. You might as well just use it. This is specific to the 3.6, the 3.2 or
predecessor to this motor. Completely different plate than that and then some kits come with a
crankshaft locking pin. You don't need that at all. This is pretty much all you really need.
You can get away without this but I'm going to use it anyways. First things first, you're going
to want to put your motor into top dead center. Take a 27mm socket, put it onto your crank pulley
and rotate it until you get that tiny little tab. You can see it on this pulley here just on the
inside aligned with that dashed slotted line there that I've painted yellow. That will put your motor
into top dead center. You'll see that piston one is at top dead center here and then on the back
you'll see that the chain sprocket here has one tooth that is shaved off. Now that just needs to
be pointing at nine o'clock or this seam in the block. So either one you need to use as a reference
and that's how we are going to start and then we'll take it from there. You guys probably still
have your cylinder head on so you're going to want to make sure that your cams are phased properly.
That's by verifying these cam lobes here. Your exhaust and your intake cam loads are pointing at
each other. If they're pointing away from each other, rotate your crank another 360 degrees
and then that should point them at each other and your cam locating tool should slide in. You might
need to take your 27mm and rotate the cam rocket back and forth just a little bit to get it to go
in freely but otherwise that's all you're here to do with this tool. You'll never use this tool
to tighten any bolts down. It's purely just to locate the timing. So I've got my old pump here
and I'm just going to push it right in. I've got some assembly lube on the o-ring and some assembly
lube all the way around here. To extract the old one I actually ended up using a steering wheel
puller and you take this outer case off and then you use these two bolts that I used as a rod
and pushed a socket extension all the way to the back to draw this assembly out. It's pretty hard
to get out but to put in this should go in and you want to make sure you clock it
as best you can because it gets a little tight trying to rotate it around.
Yeah same with your gasket. You can kind of hear the gasket's still a little loose which is perfect.
Let me put the bolts in without binding against the gasket. One of these bolt holes here were
corroded surprisingly so I had to actually tap it. This one I'm working on right now.
All these bolts are going to be torqued to eight newton meters. I didn't have this on my crane
but my engine stand is currently occupied with another build. I'm also going to tighten these
to eight newton meters as well which hold the housings together. Once that's in make sure your
pump spins freely. It does. I can feel some of the assembly oil in there so you're going to definitely
want to make sure you prime the motor before you start it. We're going to start with the
lower guide. Now they don't come with any any loctite on them. I don't know if guys like to
put loctite on them. I mean all they really need is a little bit of oil to get them to the right
torque spec so I don't know if the desired method is to have loctite. I mean factory service manual
doesn't have it so why put it on. These I'm going to torque down to 10 newton meters and this is
simply pushed on like that but what we're going to do is marking off the bolts that you've torqued.
It's always good practice. Okay so we're about to put our oil pump sprocket on. The old style
has all these windows going around it. You see one has a notch in it and that needs to point
at the 12 o'clock position or at this arrow right there. Essentially it's the flat spot
on the back of these that are pointing up as well that kind of clocks it properly. So
the new style pump has this super small window here that is going to be pointing at 12 o'clock
or kind of your sight for that timing mark. So what I'm going to do is I'm going to go ahead
and put this on and clock it properly. Double check that your sprocket here has got that one
cut off tooth or chamfered tooth at the nine o'clock position. So the order of operation is to
wrap this around your crank, fit your sprocket in and then install your sprocket. Now that
that's possible it's just that it's hard to get the links lined up properly. So what I like to do
is I'm going to make sure this comes around and you want to make sure this doesn't move now.
And what you want to do is find out what link this sprocket needs to be clocked into. So what I'm
going to do is hold it tight and you want this to be tight. This is where you're going to have all
your slack. So make sure you're holding it tight. I'm going to pick the link that matches the gear
and now I know exactly what gear or what link my gear needs to go into.
Then you can fit your chain all the way around and then fit it to the oil pump. Check your
sight and that chamfered is that chamfered tooth is also on the nine o'clock and then we're going
put our lower tensioner in. So this lower tensioner is a T30, two T30s. They say the
lightly oiled threads, there's no gasket behind this even though it's got an oil gallery back
there. I'm going to torque these down to eight newton meter and I'm going to put my oil pump
bolt in. I've gone ahead and I've torqued down my oil pump sprocket bolt down to 60 newton meters
plus another 90 degrees. I put some blue Loctite on the end of it just for precautionary measures
and while you're doing that your crank's going to want to rotate on you. So you're going to
want a second helper, second pair of hands to hold the crank at the front end and with a breaker
barge that way it kind of counteracts the the torque that you're applying to the crank section.
Now don't rotate your crank especially if you have your cylinder head on. If you have your
cylinder head off you can rotate it but most of you guys will probably have your cylinder head on
and if you do try to rotate it now you'll end up bending valves because you've got valves sticking
down into your combustion chamber. So we'll have to hold off on testing to make sure that this is
right. If you have no slack in here you're pretty much going to be good to go. We're going to work
on getting the upper chain on here and then we'll be able to rotate the motor. I am going to point
out is that this block never came with an oil check valve or a non-return valve. So what this
does is that as the oil pump is feeding pressure to the entire cylinder head when you shut your
motor off this check valve won't let that oil drop back. And this motor never had it for some reason
not too sure. If you guys experience the same thing let me know. I'd be curious to know what
everybody else has out there but I'm not going to be putting one back in because there is none
installed from the factory. So anyways I'm going to put the cylinder head on and then we'll be
right back. So to start the upper timing chain assembly we're going to do the high pressure fuel
pump sprocket. It's got a little dimple that I marked off at the top. You want to align that with
this vertical slot here that is on the cylinder head. You're going to take your drive gear
and it's got a slot in it so it's only going to be able to go in one way. Definitely grease these
up or oil them up with whatever you want, some assembly lube. So that should lock it in like this.
And then this is the specialty tool. You do it without it but it really does kind of make your
life a whole lot easier. It's slotted. This little sleeve might be in your cover so make sure you
retain that and or swap it over into here. And then you just grab a rear cover bolt and that
will fix it in place. You have your lower guide pin here installed. Grab your chain
and we'll loop it around. You want your copper colored links facing you. You want this middle
link here at this notch on this sprocket. You take your intermediate guide you can drop that in
as well. And we're going to make sure we bring it around here nice and taut. And while making
sure that this is still going to line up with its second bolt which is right there so that's perfect.
You're going to want to grab your valve control box, valve cam adjuster control box next. This
has got a little bit of a seal and screen. It's kind of like a one-piece design where this little
orange thing has a screen in it. Mine was deteriorated which is pretty common and then
sends screen debris into your cam adjusters. You can take your cam adjusters and clean them out if
you want or check them. I've already done that. You can't buy this little seal and screen
independently. You have to buy with the whole assembly which is about $1800 American. So I just
cut mine out and put it back in. Make sure you oil up these inner bores here and we'll just slide
this on. You have two dowel pins. Make sure you don't lose these into the bottom of your engine
whether they're on your head or here. Just make sure they're somewhere and not in the bottom of
your engine. So this kind of like wiggles on. You don't want to force it on or anything. You
don't want to break those little metal cd clip retainers that are in here on the end of your cam
shafts. So those are a good item to replace as well while you're in here. I definitely did do that.
So once that's seated you can then get your four bolts in here which are torqued to 8 newton meters.
I'm going to put my bolt for this guide in as well. I'm going to torque this to 18 newton meters.
This is a little tricky. This lower bolt kind of interferes with the chain. I definitely do
not want to start it angled. Otherwise I'd thread or otherwise I'd cross thread
the threads in the head. So getting that in past that chain. I'm going to pick up my lobe again.
Just make sure this stays nice and located.
Next up is our cam adjusters. So this is the intake cam adjuster. This one is
adjustable without any oil pressure. Where the exhaust one you wouldn't be able to rotate this
without oil pressure. So this has also got a 24 e on it. It's got a little
mark there on it. You can see it. I've got a little oil paint mark at the tip of it. That
is what's going to be located to the copper colored link up there. On the inside you've got
your little pin that's going to be located into there as well. So this is where rotating the
outside rotates that pin. So make sure you just rotate this as much as you can clockwise
and it'll go in no problem from there. So this has got the 32a on it. It's also got a little arrow.
It's kind of off on an angle. It kind of looks like it's got to be this tooth here. If it was
this one they would have been pointing it straight over that. So anyways that's where that's got to
go. You can't adjust this. It sounds like it wants to but you can't. It's got a tooth there as well.
It's going to be going in here and again your arrow for this sprocket is going to go to that
link. There's a little bit of slack up here. We're going to rotate make sure that that's correct
and it should come out after we rotate the motor once and get rid of all this slack as well.
We're going to go ahead and put your side guide tensioner in. It just slips in like this.
Get another pin. This is going to get lightly oiled
and torqued the same as these guys. We can go ahead and put in our tensioner. This is a 27 mil.
This I'm not going to torque yet. There is a torque value for it but not until we get everything
squared and 100% we're happy. Then I'll torque this and these I'm just going to put a little
bit of beans to them. You can go ahead and remove your timing plate. You want to make sure that
you're not causing any undue stress on those pieces. These aren't very tight yet. Things
have really tightened up which is exactly what you want. What we're going to go ahead and do
now is we're going to take this sprocket off. Checking the amount of links between the two
timing marks. You've got these two notches here. This first roller should be pointing right in the
or to this second one here to the right. That's going to be one link, two links, three, four, five,
six, seven and you want eight to where this little valley is in here. That splits that.
That's how many you want between your two cams. That's how you know it's right. It is a little
loose but you know this is adjustable so that might take the slack out depending on
where it's at. We're going to go ahead now rotate the motor and double check the timing
marks after as well. We're going to do two full rotations and get back to Top Dead Centre and
have a look at everything. Once you've gone through and rotated twice, come back down into here
check that your shaved off tooth is pointing right the split of the block and the end cap.
Check in here that your window is pointing at that tab that's on the oil pump. Now these three
copper lines that were here are no longer around. That's fine. They found their way somewhere else
because it's not the ratio is not the exact same but you're going to want to just make sure that
your fuel pump has relocated back to 12 o'clock here and then you can go ahead and check that you
have on top wherever the eight links are. So that's one, two, three. I mean these weren't going to
jump. There's no way if you had eight to start with. There's definitely going to be eight there
as well again unless something went really wrong. You're going to want to check the plate at the
front as well. That actually slides in super easy. Sometimes there's slight hesitation. You
just have to rotate the cam a little bit one or the other the other way and that's totally fine.
So that's looking pretty good. The next step to do is to torque these down to 60 Newton meters
plus another 90 degrees and grab your 27 mil wrench and you'll be able to hold the cam here
and then torque it. Do not use your plate at the front there. You will twist and break your end
the cam at the end there because they're not strong enough to hold that kind of
set we can tighten our final tensioner down to 40 Newton meter. I'm going to end the video here guys.
I don't want to bore you with the rear timing covers or anything like that but I am going to
leave you with two things. One make sure that you prime your motor before you actually start it and
secondly count your tools. Verify, triple check, quadruple whatever you have to do. Make sure
there's no tools in the back of your motor to avoid a scenario like this again. Other than that
love to hear from you guys. Any questions or comments always appreciated. Leave them in the
comment section. Thanks for sticking it out for this video. Hopefully it's not too long maybe
something like nine minutes. It's been like two months of my life but hopefully it's a little
bit quicker for you guys and hopefully this video helps some of you guys out there as
well with what you need. So again thanks for watching and stay tuned for future episodes.