Rootes TS3 three cylinder six piston two-stroke diesel engine 200 cid

Engine in Focus
4 followers
Rootes Group is a British automotive manufacturer which dates back to 1913.
Headquartered in London, England, many companies would spawn within the Rootes Group. Companies
such as, but not limited to, Huber, Commer, Hillman, Carrier, that's Carrier with a K,
Singer, Sunbeam, Talbot. Also as a separate entity, but named the Rootes Group,
would manufacture engines. Fast forward to 1945, work would begin to build an unorthodox
engine to fit under the floorboards of a lorry truck. The new engine would be called the TS3.
The project was headed by Chief Engineer Eric Coy. The Rootes Company would acquire
Tilling Stephens Company in the early 50s, which was a British commercial vehicle manufacturer.
Many believe that the TS means Tilling Stephens, but that's not 100% true.
Even though the engine was originally planned for the Tilling Stephens Group,
and then it got bought out by the Rootes Company in the 50s, TS stands for two-stroke. The engine
name would be TS3 for two-stroke three-cylinder. It was introduced in 1954, and this might be
the weirdest engine that you've ever witnessed in your whole entire life. It's a three-cylinder,
but it has six pistons, with a piston at each end of the cylinder. The piston crowns are faced
inward. Adding to the intrigue of this engine, the pistons were driven by a single crankshaft
instead of two. There was a short connecting rod, followed by a huge rocker arm, and then
a smaller secondary connecting rod, which attached to the piston. Also interesting to note that this
engine was a two-stroke diesel. Two-stroke engines complete the power stroke within every revolution
of the crankshaft. Usually, less moving parts, oil, and gas are mixed together or injected separately,
whereas in a four-stroke engine, the power stroke happens on every two revolutions of the
crankshaft. Oil and fuel are separate. Two-stroke engines also had to have a scavenging process
of replacing exhaust gas in the cylinder with fresh air. The TS3 engine scavenging system
was the use of a root blower, which was mounted at the front of the engine. It was driven by a long
quail shaft from chain drive at the rear of the engine. The quail shaft has been noted to be a
point of contention, a point of failure of the engine if overworked. The roots blower supplies
the air to the combustion chamber. Because the two pistons share the same cylinder, the piston on the
right was considered the air piston and the piston on the left was the exhaust piston. The exhaust
piston had a slight lead over the air piston. Exhaust ports opened and closed while the air
entered through the air port. Air swirled as it entered the cylinder, which also aided in combustion.
Right before the pistons reached the inner dead center, a mixture of fuel and oil was injected
into the cylinder and then ignited by heat generated by the compression of the air. The
pressure forces the pistons apart, resulting in the power stroke. As the pistons reached the end
of the cylinder, exhaust port would open releasing exhaust gases, which caused a drop in pressure
which was called blowdown. The pistons open the air port, blowdown ends, air from the blower swirls
into the cylinder towards the exhaust ports, scavenging the exhaust gases. This continues until
the pistons have passed through the outer dead center position. The exhaust ports close and the
piston starts a compression stroke. Then the cycle repeats until the engine is shut off. It's
important to note that even though this engine seems really unorthodox today, it wasn't a brand
new concept at the time. Salzer ZG9 was a two-stroke engine with the same concept. They built
two-cylinder, three-cylinder, and four-cylinder configurations before the war. 200 cubic inch
displacement, TS3, three cylinders, six piston, opposed pistons, 3.261 liters. It was good for
anywhere between 90 to 105 horsepower, 2400 rpm, 270 pound-feet, or 366 newton-meters around 1200
rpm, with a bore of three and a quarter inches and a stroke of four inches. Years this engine was used,
1954 through 1968, it could be found in the Comer and Carrier trucks. The engine was specifically
designed to be mounted under the floor of the cab in these trucks. There was also a short-lived
partnership with Lister to market these engines for industrial use, whether that be for a freestanding
engine to operate equipment, generators, water pumps, what have you. And there was also a program in
place for them to be used in various marine applications as well. It's important to note that
this engine doesn't use camshafts or valves. The TS engine would get another cylinder added, two
more pistons as well, and it was called the TS4. That engine only made it into prototype stage,
running 1.2 million miles, showing great promise for the future. But in 1968, Chrysler would buy
the Rootes company and they would cancel the TS engine, mostly due to the emissions that were coming
and they wanted to go for more of a traditional piston engine. All right, now it's time for Would
You Rather. Only one scenario today. If you had access to this engine, what would you use it for?
Would you put it in a truck? Would you put it in a car? Would you put it in an airplane? Or would you
use it as freestanding or possibly put it in a boat? Put it in the comment section what you would do
with this engine if you had it. All right, now it's time for Name That Tune. First person to give
both the name of the band and the song title correctly in the comment section will have your
comment pinned to the top of it. Thank you all so much for coming out watching this one. This one
was a requested engine. Which engines would you like to see featured on this channel this year?
Put it in the comment section below. I'm interested to see what you guys come up with because I never
even knew that this was even a thing. I didn't know that this was an engine and this is honestly
the weirdest thing that I've ever seen. I hope you enjoyed this episode. Until next time, too-da-loo!
