Lecture 4 Introduction of MOS

IIT Roorkee July 201
61 followers
186 Video Views·Jan 12, 2025
[Music]
[Music]
welcome to lecture number four on nptl
online certification course let me start
from where we left in the previous turn
and then we can go ahead uh discussing
other parts uh we will look into now the
work function difference so we have
understood the basics of FY level the
takeaway was when the FY level is close
to the conduction band n type close to
the valance band P type if you give a
positive bias on the semiconduct on the
on the on the metal side uh the F the
bands will go down on the semiconductor
side if you give a negative ative bias
it will go up if it's a n type and P
type semiconductor and as the firmy
level becomes closer to the conduction
band near the surface electrons gets uh
uh added there and uh as you move away
from there you you have depletion region
being formed there this we have takea
away from a previous slide let's look at
a metal
semiconductor uh contact here and let's
look at the energy band diagram of a Ms
with oxide layer of course in the middle
of it so we are now going in a
transverse direction from metal towards
a
semiconductor now if you look at the
right hand side here this one right hand
side then we Define two important terms
here one is known as the electron
affinity Kai is defined as the electron
affinity and is defined as the the
amount of sort of uh potential which you
need to give for an electron to move
from the lowest edge of the conduction
man to the vacuum level what is the
vacuum level vacuum level is the one
where uh the energy is approximately
equals to zero so what happens is that
it is not in the bound State now it is
almost like a free state right and the
amount of potential in order to shift an
electron from the edge of the conduction
man to the vacuum level is referred to
as an electron affinity and the amount
of energy required is Q * sky or E * sky
here right
now if you look at the left hand side
which is this one then we Define a term
FM here and this FM is my metal work
function metal work function and this
actually goes from the the the in in in
energy domain from firy level to the
vacuum level right so in the metal
obviously the fir level is very close to
the conduction band or almost has
crossed inside the F conduction band and
if you give a bias there or if you give
a uh or the distance between in energy
terms the distance between the FY level
and the vacuum B vacuum is basically the
uh the metal metal uh work function now
on the right hand side again if you look
on the so look at the metal
semiconductor contact and let's
concentrate here I am telling you that
this EFS is my fir me potential very
close to EV primarily meaning this is a
p type semiconductor or P type silicon
available with me this is the conduction
band for the P type semiconductor this
is the valance
band now in silicon dioxide which is the
Moss capacitor let us assume that my
band Gap is very high it's approximately
9 electron volt and so this is my band
Gap and this is the conduction band of
of silicon dioxide and this is the
valance band of silicon dioxide and Kai
I is the electron affinity for oxide
layer right so in the oxide layer if you
want to take an electron from the edge
of your conduction manand to the vacuum
level we Define that as kaii or
intrinsic firy level right so we have
learned three or four important points
Kai is basically the one which is goes
from the conduction band edge of the
semiconductor to the vacuum level uh F
of M is basically the work function
which basically implies the amount of
energy required to move from the fir
level Edge to the vacuum level in the
metal once you have understood this
three important terms we try to bring
the metal oxide and semiconductor closer
to each other right and so I have a p
type semiconductor this side I have an
oxide layer I have a metal once I bring
them
closer obviously what happens is that uh
the bending on the pide semiconductor
happens towards the below uh because you
have let us let us apply a positive bias
on the P side it goes to below now my
EFI right EFI actually crosses my EF so
intrinsic firmy level crosses my firmy
level by application of a bias this can
only happen when your oxide conduction
band show shows an edge right so
otherwise if if no bias would have been
present it would be something like this
right with bias this becomes like this
because all the energy levels will be
pushed downwards and that is what is
happening here right so we have now
energy band diagram shown on the right
hand side and you can see here that your
uh your your intrinsic fir level has
actually gone below your firy level here
and the effective value effective value
of your electron affinity has actually
reduced from eai to eai Prime right why
e Prime because now in order for
electron to move towards the metal side
the amount of energy required to pull
over will be exactly equals to e Prime
which is the which is the oxide layers
conduction band's highest Edge if you're
able to cross that then it's a downward
Hill and that's the reason your eek I is
the effective effective uh electron
affinity energy at this particular point
this is energy band diagram for moss in
thermal equilibrium right and at thermal
equilibrium I'm maintaining all of the
all of the graphs
here this gives you a brief idea about
this thing I will request you to do a
moss with n type substrate on the on on
on towards the semiconductor and apply
the same principle there okay now what
we do we enter into a new domain or new
area since youve understood the energy
band diagram we will take because now we
enter slightly into the concepts of moss
structure right we'll take a moss
structure and try to explain to you the
three conditions of a moss structure
that is flatband accumulation
depletion and inversion and then we will
finally look into the three terminal
Moss structure and look into the defects
in the Moss capacitor these will be the
outline for the
subsequent uh few lectures or few uh
portions of the lectures in
subsequently now let's look at one by
one we have already done it but but this
will be now a new thing which I will add
here now so look at the right hand side
right the right hand side is basically a
moss where you have a gate metal have an
oxide and you have a silicon
semiconductor which is n type and P type
and then I'm giving a gate bias which is
zero so basically have shorted this gate
to
Silicon we have already
seen that if you if you want to find out
uh so you see the first statement which
I've written here the flat band is the
condition with the energy band EC and EV
of the substrate this one is flat at
silicon silicon dioxide interface which
we have already seen in our previous
discussion if you don't apply any
external bias they will be exactly flat
at silicon silicon dioxide so if silicon
silicon dioxide interface you will have
EC EV
right and then EFI if it's an p n type
semiconductor this will be EFS and they
all will be straight right primarily
meaning that uh you haven't applied an
external bias right and if you therefore
some all the contact potentials from the
gate through the external external
connection into the bulk I will get V of
f or the F of VB five this can be as
five of VB to be five of gate minus five
of bulk we have already done this in our
previous lectures and therefore I will
not stick to this too much what does it
tell me it tells me that because of the
difference of contact between gate which
is a metal and the bulk which is
semiconductor there there you required
to give an extra push for the electron
to move from Material gate material to
bulk material or vice versa and that is
given by VF F of VB in this
case what what will be uh uh what will
be uh what will be your flatband in this
case simply vgb gate to bulk vgb will be
equals to
vfb which means that I since you didn't
apply any bias there will the the
charges or the or the channel charge per
unit area will be zero and of course
since the charge is zero surface
potential is also very very much equals
to zero right and your vgb will be
equals to vfb that is what is a flatband
voltage condition which you
see this is the diagram which I was
referring to in the previous St so have
a moss structure I have a metal here I
have a oxide here right I have a
semiconductor here right and and and
let's look at the Moss structure here so
we already know that at equilibrium 5m
minus 5 S is the value right so what we
do is uh on the if you see your K of
silicon dioxide is very very high right
it's it's relatively very high similarly
the kai for silicon is 4.05 electron
volt which is written here for silicon
uh we have written here therefore this
is the conduction bandage of met of the
silicon and this is the conduction band
Edge for um on the metal side right
now uh if you if you look at the right
hand side then q q * 5 S which is the
amount of energy
required sorry the amount of energy
required for the electron to move from
the semiconductor fir level to its
vacuum level is given as Q * SII will be
given as this much this is the electron
affinity this plus this this is nothing
but EC minus EF so you see what we have
done we have we have written Q
s of s is equal to Kai silicon plus EC
minus EF higher the value of EC minus EF
or Kai silicon the value of my Surface
potential also becomes
larger and that can be visible from this
uh from this particular uh graph or from
this particular schematic at
least uh this is one aspect which I
wanted to Showcase to you which means
that the surface potential or Q in Time
s is dependent on two factors and the
first factor is electron affinity and
the second factor is the difference
between conduction and the form EF
conduction of the
formul whatever I'm teaching you is for
let us suppose this is for an this is
for a p type material I would request
you to go for discuss with for n type
material as well please try to do that
how this is working now this is n plus
polysilicon right this is n plus
polysilicon you can also have metal uh
metal aail aailable here this is an
oxide layer whose band Gap is typically
9 electron volt very very high but the
band gap between in Silicon is
approximately 1.1 electron volt this
this is typically 1.1 or 1.2 electron
volt which you see the value is 3.1
electron volt from the conduction band
edge of the Silicon to that of that of
oxide
layer right and uh this gives you a
brief idea about the flat band condition
so I haven't applied any bias the Bands
are absolutely flat primarily meaning
that no charge carriers are developed
and therefore the potential is exactly
equals to zero right and that is what uh
you will you will come to know now let's
come to the first part of it and that is
known as the accumulation region what is
accumulation region is when you apply
gate to bulk or gate to bulk negative
potential when you apply a negative
potential then s the majority carrier
concentration right near the surface
which surface silicon silicon dioxide
surface become larger than the
equilibrium electron hole I'll give an
example let us suppose that t equal to
300 Kelvin and with no bias you will you
and let us say because of thermally
generated charge carriers you will have
some electron whole pairs generated
right let us assume those to be a
thermally generated electron and whole
pair now when you apply a negative bias
you tend to generate extra charge
carriers there so therefore the majority
carrier concentration near the Silicon
silicon dioxide interface becomes much
larger than the equilibrium uh electron
and whole
concentration and when you
apply what is the meaning of negative
negative primarily means that my gate to
bulk potential or gate to body potential
should be below vfb or vgb right so if
which means that let us suppose your vfb
is equals to minus1 volt then if you
apply a gate to bulk of -3 Vol then we
Define this to be as an
accumulation
accumulation right and this is so let's
let's look at the fact what happens if
it's negative very true if you apply a
negative vus Which is vgs less than zero
then all my holes if it's a ptype
semiconductor all the holes in the ptype
semiconductor will be rushing towards
the Silicon silicon dioxide interface
and you will have a large amount of
charge carriers positive charge carriers
sitting somewhere here in the interface
region right and this is accumulation
you're accumulating the charge carriers
there uh the same type of charge
carriers as there so if it's a p type
material you will be having pulling the
holes if it's an N type material and
apply a negative bias the electrons will
be pushed backwards and the holes will
be created near the uh near the region
right so you see for a p for an N type
semiconductor uh for an end type uh end
type semiconductor if you want to form
the holes as the charge carriers then
you have to give a negative bias to pull
the holes and for a ptype semiconductor
if you want to form n type layer of
inversion layer then you have to apply a
gate voltage which is positive in nature
so at a very early instance you can
understand the difference between a
positive bias and a negative
bias so you see I can safely write down
VG to be equals to flatband voltage plus
surface potential plus VX already
discussed with you and VX the voltage
across the across the so this is also
scox which I'm using is the voltage
across the oxide layer is given by VG
minus vfb the gate voltage minus flat
band you apply the gate voltage you
spend some of the gate voltage in
flatting the band and the rest of the
voltage appears across the oxide layer
and it is given by substrate minus time
substrate by coox so you can use it as
per unit area also or you can use it as
a total charge
also this is the band diagram in the
accumulation region right and and it
should be clear to you before we move
forward I told you earlier that in the
accumulation region you're accumulating
holes near the semiconductor interface
oxide semiconductor interface so this
will be an area where we will be
accumulating holes as a result the
energy levels will start to move up and
that that's the reason you see these are
all moving up right moving up and as you
can see Valance band has been closer to
the to the fir Lev level which primarily
means the number of holes have actually
become larger in this case as compared
to anything
else fine um we Define the new value of
the firi of the electron affinity as Q *
KY Prime where Ki Prime is the effective
electron Mobility uh uh when you do have
a bias being applied on the uh metal
side right and on the P plus Poly on the
metal side as you can see my fir level
is almost equals to the edge of the
conduction balance band here right and
if I assume it to be as a p plus poly so
it's a p plus poly oxide and you have a
semiconductor which is again A P type
right you can have the such type of
accumulation uh more is the bending
upward bending towards the semiconductor
more it goes into accumulation more will
be the charge which is getting
accumulated at this stage in the
semiconductor right so please keep this
in your mind as far as uh uh as as far
as uh this this concept is concerned
right let's come to the last stage and
we will do inversion later on but let's
come to the depletion State what is a
depletion depletion is when you give a
vgs value gate to gate to bulk or gate
to Source gate to body value
slightly positive but not very large
positive when you give a slightly
positive I already discuss with you what
will happen in this Cas is interestingly
that the oxide if you apply a posit let
me show it here itself so if you apply a
positive bias here then the electric
Fields will be all in this direction
right all in this direction right and
then when the field is in this direction
uh you will be basically depleting this
area of free charge carriers because all
the holes will be shifted let us assume
that this is a p type semiconductor and
VG is greater than zero then holes will
be dropped below the surface silicon
dioxide and there will be a space charge
or depletion region formed between these
two and the width of the space charge
which we had defined earlier as XD will
remain constant As you move from this
end to this
end please understand this point very
clearly why it will be constant because
I am not applying any bias on the right
hand side of the diagram on the left
hand side of the diagram yeah I'm
applying a bias in the top side so if I
assume that the potential Electric
fields and potential are exactly the
same in all the direction the amount of
potential visible at this point in the
interface at this point in the interface
so at these points if you see the
effective potential visible to you will
be after the oxide voltage drop and that
potential will be responsible for
forming the depletion
region right that potential will be
responsible for forming the dition
region and it will be constant As you
move from left to the right
it will be constant however we will see
later on when we use Moss as a three
terminal device that once you apply a
potential on the right hand side or on
the left hand side the depletion
thickness will not remain same across
the whole device but it will go on
becoming smaller and smaller or larger
and larger As you move from one side to
another when you apply a bias
now as as as written here if you apply a
small positive gate gate to Source
voltage the minority carrier con
concentration will leave the leave near
the oxide silicon interface and only
fixed or acceptor or donor ions will be
remaining there so these are fixed
charges and therefore they will form a
positive bias at this particular Point
uh look at this right hand side curve
here this diagram here in the depletion
region it will the bands will be moving
downwards towards the semanda side but
it will be not very down it will not be
too much down it will be just going a
bit down right and we find VG to be
equals to vfb plus cs plus VX already
discussed CS has got a formula given by
this and uh VX can be given by this and
uh we can write down this to be as VG =
to vfb plus Q * na W depletion Square by
2 Epson silicon plus Q * n w depletion
by CX so on what factors does
the uh gate voltage uh or the basically
the voltage varies the or or on what on
what part does the gate voltage go on so
this gate voltage which we apply will go
on to make the bands flat first of
all then some of it will fall across the
oxide layer and the rest of it will
appear as a surface potential which will
be actually depleting the channel right
and and this one is relatively easy to
handle because I'm again assuming that W
depletion is is
constant in reality not true when you
apply an external bias
uh either on the drain side or the
source side of aosi right so this is the
depletion region let me come to the very
important part and that is known as a
threshold condition so we have
understood we have understood uh uh
flatband we have understood accumulation
we have understood depletion let me come
to now inversion and
threshold now if
vgs uh which you've applied gor Source
voltage
is uh quite high and it is equal to
threshold voltage we Define a term
threshold then uh when when my vgs is
exactly equals to the threshold voltage
I will I so what will happen when vgs
was was slightly positive I was able
to push the holes below and you had a
depletion region divid of any free
charge carriers near the Silicon silicon
dioxide interface now still go on
increase in the gate voltage but a time
will come when the electric field will
be substantially large to pull the
electrons right now pull the electrons
means it will be pulling the electrons
from the substrate and source and drain
later on towards the
interface once it pulls the electrons
near the interface you will have free
charge carriers available right so you
will have these so you will have free
charge region here you will have free
charge region here and there will be
also depletion region
here
right I'm not writing I'm not deriving
anything here I'm just writing the value
of the threshold voltage to be equals to
this this quantity here you can have a
look from numerical point of view
therefore the surface is no longer in
depletion but in the threshold of
inversion how do I Define inversion
inversion why the name inversion has
come so you see if you look very closely
initially this was a ptype semiconductor
right I had applied a
bias removed the holes from the
interface made it deplete and then I am
doing an ENT I mean I am putting
electrons there so the charge carriers
have inverted from P type to n type and
that's the reason it is known as an
inversion an inversion layer has been
formed the voltage at which this first
layer of electron comes and it becomes
exactly equals to the number of holes
initially we Define that to be as the
threshold condition right so if you want
to therefore have electrons available in
a ptype semiconductor near the Silicon
silicon dioxide interface you have to
give a gate voltage equal to the
threshold voltage of the
device let's look at the band diagram of
a threshold voltage right let's look at
the band diagram of a threshold
voltage uh you're applying a positive
gate bias please understand which means
that you're applying negative towards
the semiconductor now you know that it
is minus Q * V right so what will happen
is that the the the bands will be pushed
inside
or down it will be push down means in
energy domain it will go down when you
apply a positive bi at the metal side so
when you apply a positive bi of the
metal side and assuming that the metal
to be an end type
poly my conduction and FY level are
almost overlapping with respect to each
other and my Valance band is very far
off and then uh what I do is I will see
that this is EV EF EI and E see the
conduction band intrinsic F level the
firy level here and the valance band
since EF was close to E I can safely say
this to be as a p type
semiconductor right now what has
happened is you see when I applied a
bias on the metal side thereby pushing
it downwards if my intrinsic fir me
level goes below
my uh external F the form level which is
there for the metal which is there this
one ef
ef then the type of carriers actually
get reversed
so what will happen when suppose this is
my EF right you applied a potential ey
in flat band was something like this
this is this was the flat band EI you
apply the potential bending takes place
and bending becomes exactly at the edge
this is the edge of the depletion which
you will find out you still go on
increasing it you will you will get
something like this so it goes below EF
which means that if initially it was a p
type now it becomes slightly an N
type and we Define q into 5B is the bulk
potential here right Q is equal to Q
into c q into 5B is the bulk potential
right and that is what the effective
potential is available with you uh let
us look at this point d uh the the this
this is D this is D higher the value of
D more the bands will be bent downwards
and therefore more will be the number of
free charge carriers in this case
electrons because it was initially type
right and this can only happen when you
give apply an external positive bias to
this case right so so this is the
threshold condition sort of a band
diagram I want to discuss with
you now let's come to the definition of
strong inversion region right strong
inversion will happen when vgs is very
very large as compared to 0 volts it's
very pretty large right and it and and
becomes large uh very large I will don't
look at the don't look at the formula at
this stage it becomes very large let me
see if a diagram available to me no I'll
explain it from
here if I want to make it uh so so I
will I will I will change it I'll change
my explanation slightly when this EI
becomes just touches EF so when EI
exactly equals to EF that is the onset
of
inversion inversion
and when EI becomes further down and
this distance suppose this is X and let
this is y when x equals to Y right so it
it has now become lower from the form
level by that much as it was initially
higher than the formul level then we
Define that to be as a strong inversion
right so inversion is when when this EI
meets with ef at the interface what is
strong inversion when EI crosses EF and
almost it crosses up by how much two
times so initially suppose it was it was
here this distance was X and this
distance was also X then we Define this
to be as a deep inversion please see as
you move inside the
semiconductor your variations are not
there the variations are only visible to
you when they are very very close to the
interface of the semiconductor interface
so this is the right hand side picture
gives you the electrons getting
attracted large number of electrons are
available here and you have VG much
larger and this gives you an inversion
layer now look at the left hand side the
explanation of this thing you have on
the left hand side you have the maximum
width of the depletion region is given
by 4 * epon silicon 5 bulk upon q and
the inversion layer density which you
get is C so C into V is Q so c q inverse
is negative because I've inverted it so
I get a minus sign here I multiply coox
VG minus VT where VT is the threshold
voltage why because if you apply a gate
voltage out of which let us suppose you
apply a vol gate voltage of 2 volts then
out of which one volt is just gone to
form the in or to form the channel so
what you do is that you substract the
threshold voltage from the gate voltage
to see the effective gate voltage
available to you that you multiply with
CX to get the total inversion charge so
this is the inversion charge definition
as far as strong inversion is concerned
we will take up three terminal MOS
device in the next turn thank you very
much
[Music]
a
[Music]
