This 1942 Philco Radio Just Keeps Getting Worse!

Amateur Repair Time
257 followers
4 Video Views·Jan 7, 2025
ladies and gentlemen welcome back to
amateur repair time now if you were
watching our previous video on this
radio we've been working on this cool
old
filco and when we got into it we found
that it had
been reworked at some point
and regardless of when it's been
reworked the lines are just the wires
are just disintegrating in it it's got a
lot of rubber lines in IT wires in it
and they are in horrible shape this
thing's from
1942 so uh it's quite old by now someone
has apparently replaced the rectifier
tube with a diode and they left the tube
in so that the series The the string uh
voltage would still light up the other
tubes I guess so what I need to do is we
need to start replacing some of these
rubber wires um we're just not going to
worry about where this goes for
now
um I believe the first thing we can do
is we can get rid of one of these one of
these this is coming from the field coil
on the top and needs to attach to one of
these
connections and they had something else
on it running up here so let me see up
to
that so we can pull that
entire wire
out it appears that they had that hook
to
the um
at some point the filter cap someone was
saying oh you should just take
everything out and then start all over
again clean
well this is amateur repair time
folks yeah so this appears to be the
wire that ran over from that
PIN to connect to
the um the filter cap one of the filter
caps but as you can see see it's had
better
days so that line
there needs to come
off all right so that is the one that
that wire needs to go to but I've got
all these other ones screwed up here
under it that I got to replace before I
can put this down so this pin here had
two wires coming off of it and a cap so
one of the wires was a yellow wire that
goes all the way over here to here okay
so I clean that up and put a new one and
it looked
like
this I'm sure it was originally white
but it's yellow now this is the one that
we removed that apparently went to the
filter
cap okay and then there was another one
on that
same lug that we're talking talking
about now that would have I guess that
would be 1 two three pin
three which is not actually used on the
um tube they're just using that as a
junction point right which you know
that's kind of hard to figure out on
this line Point too soldering that they
do but they're just using that because
it's an extra piece of metal that they
can connect a couple things to so that
green
[Music]
wire is this one
and so it went from
there up through the
chassis to
the
antenna right and it goes on that weird
little leg there that sticks off the
side all right now on that same pin so
those two wires
there on that same pin there was this
capacitor and it goes from there to
there I left it on there so we can J
hook the new one on all right now if you
look at this
capacitor it is very clearly a fil Co
that's an original
one that is the part number and it is
very
clearly a
0.1 microfarad
so you see that right it's
a01 0.1 very clear to
me all right so that Capa that capacitor
is coming from here over
to this tube whatever it
is and let me see if I can figure out
what pin that is I can't see where it
starts
well we should be able to figure it out
just from
minut so here is the
schematic this is the antenna that we
were just messing with see pin four
there how it sticks off to the
side so if you look over
here this is the
antenna and there's pin
4 and so one wire runs
off and connects over to the 7 CB I mean
7 C8 7
C6 um over in the corner that is that
yellow wire that we were doing and then
whenever it gets over there there's a
resistor connecting one pin to the next
pin right so that's the yellow wire that
we
replaced and then we have the green wire
that goes from the
antenna now remember they're connecting
them on a empty lug down here um so
we've just connected that to the antenna
on that extra lug on here and then there
is a cap coming from
there
um
to the
788 so it's an unused lug here to there
that's what we were just looking at and
it is a 0.1 but if you look at
this the only
connection is this and it's labeled as a
0
Z1 now where we connect
that it's basically going
from oh you know what that's ground
actually h
we're going to have to figure out what
exact pin that's on to make sure we put
it on the right
spot well that's got to be it it's 01
and see how it says number eight on
it that's not ground but it's that is
the neutral line which I guess is ground
well anyway if you go up here
here of course it won't let me do
counterclockwise but if you go up here
you'll just have to take my word for it
if you look at number eight it says
condenser
0.1 200
volt right so it's a typo on the
schematic but in the parts list they get
it
right um yeah so I'm going to go make
sure that that is going where we think
it is and then we'll put a new one
in now all right so I'm about to hook up
those wires that they had on the diode I
made a mistake in the previous video no
one corrected me on it that's that's
strange usually people tell me all the
time when I'm doing things wrong but so
this is how the 35 Z3 is on the
schematic you've got the two heater
um lines on the the uh top up there and
then I was saying that this is the
cathode and that's the anode but that's
actually wrong because they're drawing
the tube upside down
that is the cathode and that is the
anode or the plate so the plate is going
to these
resistors
um it's kind of strange that they drew
it like that but I'm sure it makes some
kind of sense now if you look at the
other ones you can see that the plate is
usually drawn up at the
top and the cathode is usually drawn at
the bottom but you know that's that's
how the tubes are made the cathode goes
around the heater and then the plate is
up at the top but this one's was drawn
upside down so I was incorrect when I
said that so the wire from the field
coil needs to go where the cathode goes
and then the wire from the resistor
needs to go where the anode
goes so the wire from the resistor needs
to go to pin two and the wire for the uh
field coil needs to go to pin
7 all right so I put shrink tubing on
The Wire coming from the field coil this
is the other wire coming from the field
coil and uh it's on
pin
7 and then the resistor over here that
was connected to the diode is on pin
two I replace the wire that was on pin
one because it was all screwed up it
comes over here to this side of the
resistor um I believe that's the um that
would be the heater
and then this is the other side of the
heater it runs off to here I guess and
then the other ones to make the string
we replace those too I put the cap in
that we were talking about put a little
spaghetti on it uh I need to put replace
this need to figure out where that
went um and then we need to replace this
one and then we'll be done with this
socket at least I need to measure those
resistors in there to make sure they're
all right I guess there's just one I
need to measure to make sure it's all
right and replace place it if necessary
and then I think what I'm going to do
with the filter caps is just run
lines back over to here cuz they were
supposed to mount right
here
um I don't know where they had them
mounted I don't know what they were
doing but that one wire that we were
talking about was sticking up here
somewhere so whatever but I'm going to
run them I'm I'm just going to run two
lines to whichever pins they go to um
and then run them back over here so I
can Mount them over here where I've got
a little
room well it's going from bad to worse
folks um the field coil is no good so
it's supposed to be 500 ohms it is not
it's open which you can see
how I
mean it's just
decaying it's a damn shame too the thing
was pretty nice shape so I'm going to
have to put a different speaker in it
and rig up the a load for that field
coil or something I don't
know I don't know but I'm just going to
keep going through it like I was and
we'll figure out the speaker thing I'll
have to I'll have to get another that's
probably a three and a half or a 4 inch
speaker
um I have to research how to do that
people have been telling me in the um
comments the best way to do that
but that's a real Downer I I was
hoping that um we could be able to save
that
but what can you
do all right so we were up to here and
that attaches over here
so maybe we got to figure that out first
so I can go ahead and mount whatever
we're going to mount to to get rid of
that field
coil
um before I bury it all back underneath
this cap and this cap and all the stuff
that gets mounted here the oscillator
and the two caps
mainly
um
yeah so that
sucks all right folks I've been messing
around with this thing and there's just
so many wires screwed up I decided I
need to basically get rid of all the
junk first so this side over here
everything appears to have not been
Disturbed so everything hasn't broken
apart yet to the point that it can short
anything with the exception of that one
but we're good there so all of our
problems are over here in this corner so
I took out the Caps that were there uh
the it's been I've been working on this
a while so I'm talking several weeks so
I don't know if I mentioned but the
field coil is screwed
up I tried taking it apart and digging
it
out it's just it's broken in there
somewhere I was hoping it would just be
like where where the lug is or something
nope so we're not going to be able to
use that um so we remove that uh the
Transformer all kinds of
stuff I've removed a couple of the caps
and I've replaced the deteriorated
wiring so this red one and there is
actually a blue one under there too that
routes under it that I've
replaced I don't know if you can even
see it
see it up in there see it so nice new
wiring yeah it ends up over here nice
new wiring and these so I think what I'm
going to
do since we need to come up with
something to replace that field coil
we're just going to have to rebuild that
part of it you know and and if you
watched the first video or the the first
part that we did of all this I was
making fun of this guy not really making
fun I was just saying that it was way
too much I wasn't going to do it that he
had taken everything off of his and then
started from scratch and one of the
comments somebody said oh yeah it's all
screwed up you should just take
everything off start from
scratch and I thought that's crazy yeah
I don't want to do all that but you kind
of got to take a bunch at least a bunch
of it off because the wires are so
deteriorated look at this look under
look on my table here look at all that
that's rubber off of the
wiring absolutely L
nuts so I think what we're going to have
to do is just work through the power
supply first it looks like most of this
the wiring is going to be intact we'll
be all right but this power supply is
where all the problems are
so we have this across the line cap here
this
this 04 we'll call
it um one side attaches to the
switch and one side attaches to the
resistor now this resistor is a special
resistor that's two parts it's basically
a resistor with a center tap right so if
you look the cap is attached there but
also the power cord is attached there on
this model it doesn't have a clock and
didn't we figure out it oh it does have
a lamp I see the lamp up there
um so where this cap is that we've
already put on is also where the power
cord needs to go I believe when we got
this one wasn't the power cord already
removed like said it's been a while
since I messed with it and someone has
written on the front of the
resistor 45 ohms from here to
here and 130 ohms from here to
here so This Is 40 instead of 45 and it
should be
120 Al together so it's a little off but
that's all right especially if you think
about how the line voltages went up over
the years so so where this cap is is
where we need to attach our power
cord and the cap is right there one side
of it is on the resistor and the other
side is on the switch that's that new
cap we put in so our power cord is going
to be in that exact same spot and that
will allow the switch to work and
everything will be hooked up like it
should
be okay so coming from
there the center tap of that
resistor uh should feed the light bulb
should be across that resistor but then
it should also uh feed the cathode of
the um or not the cathode that's
actually the anode because this is drawn
upside down uh the an the anode of this
35
Z3 right now I can't remember which pin
that is on this socket but we already
did all that too right so if you
look the center tap of the resistor
is heading down to that pin on the
tube uh which is the
anode
okay now if it has the lamp the two
wires for the lamp should also go across
that part of the
resistor in
parallel and if you look very
carefully see that little wire running
off up to the top right
there and then I I guess there's a a
white wire there is that one we replaced
already is that what I'm seeing
here oh no it's a it's a sleeve on
it all right so that's the two
wires running up to the lamp
here now the reason that they're kind of
Helter Skelter is because oh never mind
this is not the same one I was thinking
this is the one where it moves I've had
one where that actually moves the lamp
is on the the dial
indicator okay so that is hooked up fine
we'll have to check those wires again
just to make sure everything's uh not
shorted or falling
open so we're up here so the rectifier
is going to do its
thing right and the other side of the
switch has a line that's going to run
off hit two caps and then hit the other
side of the
string so I have went and looked up the
socket pins of the heater lines on the
string on the on the different
um um
tubes so from the resistor the end of
the
resistor we should head off the pin one
or eight of the 35
Z3 if you look this wire here is just I
don't even know what the hell that goes
to if you look it comes off there comes
down and that is uh pin one I believe
isn't that how you do it you start at
the Notch and then you start counting
clockwise so it's pin one okay now
pin8 is that red wire there that I
have
replaced so from there that should run
off to pin 2 or 7even on the 50 L6 GT
GT and if we look here if I
can there's so much in this setup
here where is our Notch yeah there it
is so is that pin
[Music]
two can we tell from the top probably
not
one two three four five six seven so we
should have two here that's suround the
notch that don't have anything on
it they call this too much booty in the
pants there's too much stuff down in
here
I cannot see through the
phone if that's pinned two let me make
sure I'm just trying to double triple
check
everything it is that's pin two I
believe may be pin seven but either way
okay
so the other side of
that is this pen so this wire
here continues the string and it's
heading on and boy it looks like it
might be deteriorated is
it that gray one down there I think I
lost it in the mix
here it must be going to this
socket hey y'all clicked on the video
you can't complain too much the rest of
them are one and eight
again so so that is
[Music]
pin
eight
yes so it's connecting to pin eight so
pin
one it's just
unbelievable it's unbelievable folks
I'm trying to get a good Gander at Pin
one that's it
right that's it right there so it's this
wire
here that off it
goes and it runs over
to pin eight on this
one right there so pin one is that one
so it's another wire that snakes under
this
thing that's it there slightly
deteriorated but not the end of the
world and it runs to that pin right
there which is pin
one and then finally we have pin eight
which is that
one it's kind of scary looking isn't
it is that correct why would they have
resistors on
it that's pin eight yeah there are
resistors there for it okay so it snakes
back around
and ends up
here which is probably an unused pin
that they're using to Junction
off to something else that might be a
good place
to that might be a good place to attach
some of the filter Caps or
something spins around to
here so they're using unused pins on
this socket I
guess and it's that yellow wire that
we've
replaced which runs back over
here and is attached
to pin
it's a pen I cannot tell one two three
four five pin
six which may be the same type of thing
going
on shouldn't we have ended up back at
our
switch or did we is that what the yellow
wire is
[Music]
what a freaking mess nope it's not the
yellow
wi I so you see the uh you see the issue
here all right I got to I got to look
through that last one one more time
because we should end up back at the
switch and we
didn't aha I have figured out we did end
up back at the switch if you
look uh those two pins are tied together
so they've tied pin
eight and pin seven together and then
you see that rubber that black rubber
blue rubber wire coming off of that
snaking down under
there and then see it right there it
connects to the other side of the
switch so that the string is intact so
all of this is
together this is the neutral
side which is running up to connect some
of this stuff my thought is with the
field resistor out which we
have our voltage should stop right here
coming out of this
rectifier so we should be able if
everything's clean and we're not shorted
anywhere and if we bring it up slow and
watch it if we've got the five tubes in
we should be able to get glow on them we
should be able to put the power cord
back on and then we should be able to
measure voltage right here at this
cap right even if the Cap's not there we
can we can measure from here to
here and see if our rectifier tube is
working and if our string is working and
that's as far as we've gotten so far so
I'm just trying to minimize everything
get everything back to basic so that I
can test what we've got and work through
it slowly and try to rebuild the thing I
think most of this is still in there I
haven't cut all of it out what a what I
messed with was the wiring around
here and around
here so that's what we need to mess with
there's our output
Transformer the speaker that's
missing the FI coil that's missing ET
I'm going to try to replace the field
coil with this
resistor we'll see how that
goes um so yeah so I need
to install this
capacitor and I need
[Music]
to make sure this capacitor isn't there
I would like that and we've got this
disconnected for sure
and then bring it up really
slow that's the
plan all right folks so I have carefully
checked all of those wires are fine I
have this one I need to mess with
obviously and we've got a stray one here
you know we got stuff cut out here but
pretty much I've got it isolated because
that field coil is
disconnected so without that we're not
going to get the 95 volts there but
we'll get something here
here right so I have installed this
capacitor I looked up this pin out pin
seven is the
cathode and then it's connected to the
other side of the switch well if you
look the other side of the switch
connects to a bunch of things
actually including the main rest of
the schematic so that is this wire here
it goes all the way down here we
replaced it
earlier comes down to here it jumps
around it does all kinds of stuff and
then it comes back over to
here so I even checked it with the
multimeter that is actually where the
negative of the capacitor is supposed to
be and then it's supposed to be
connected to pin 7 which is right next
to it so I just put this right on the
bottom of the socket now I know what
you're thinking a lot of you people
would do it a lot cleaner than that and
it' look lot nicer right but remember
this is amateur repair time and I've
never had to work on one that's this
screwed
up but I think what I'm going to do I'm
going break out the the uh um I'm going
to break out the the um my trusty fac
over there so we can bring this thing up
slow and I'm also going to put a um amp
meter on it so I can see how much
current it's drawing to see if anything
shorting and we should be able to watch
that and as long as it doesn't start
shorting we should be able to bring it
up and just see if we get glow on our
tubes which I have
reinstalled uh and see if we get any
kind
of anything out of this rectifier it
could be the rectifier is bad too you
know but I've probably got some more so
I think that's where we're at so I'm
going to try to plug her up and we'll
see what happens oh I've installed the
cord
back that wasn't there whenever we got
got it cuz they had the sense to cut it
off and I popped a little grommet in
there if you don't have any of these I
tried to get some that were made in the
USA but I couldn't find any you know I'm
big on made in the USA um so these are
made in China but I got this grommet
assortment all different
sizes so that we don't have to worry
about this cord getting all screwed up
all right so I think we're about ready
to mess with it now I know a lot of you
are frightened for me right now but if
you're seeing this video I must have
lived through it so don't be too worried
so here we
go all right now if you haven't seen me
mess with this before boy you're in for
a great
treat remember this is amateur repair
time so I have a varc it's on zero volts
right now I have it plugged in and it's
fused and then I have
this am meter plugged into it and then
the radio plugged into that so it's
going to get his power through that
meter and from the
variac
um and we're and I've had all kinds of
people complain about everything this is
not turn sideways that's how it's
supposed to be the feet are on the
bottom of it okay so that's the first
thing um but um I've got it set on its
lowest setting so it can go up to one
amp that's the meter that it's using so
we're going to turn it on this thing
should only pull like0 2 amps or
something like that I didn't do the math
but it's not much right and that's with
it fully working so all we're trying to
do is get the tubes up and warm so uh
we'll see here uh so first thing I'm
going to do is turn it on and see if we
blow a fuse or this starts shorting or
what now remember it has zero volts
really okay so it's just a switch and
the volume knob and the volume knob is
not going to work because the whole
meter is not doing anything I mean the
whole radio is not doing anything so I'm
going to slowly turn it up and let's see
if anything starts shorting once we get
up to like 20 volts or
something we're at 30
volts 40 volts
50
volts 60 volts that might be enough to
get some
glow keep in mind too if you've got a
bad connection on any of them
the string won't work nothing but it
could be our voltage is too low here we
go all right we're at 120
volts nothing
these are the lock tools that um Shango
was always complaining
about and you know we should be
getting our lamp on too
if the lamp's not burn
out well sure enough and I have seen
this before the rectifier tube uh the
heater is burnt out
so
basically this is not connected so since
that isn't connected they're all in
series so you won't get I mean most of
you watch watching this I'm sure know
all this more than I do but you you
can't get any of these to light up if
any of them are burn out and so this one
the heater element is open on it and the
way you can test it is just check the
resistance between pin one and pin 8 so
on this one for instance the resistance
is infinite it's not connected at all
and that's why the power won't run
through it I pulled all the other ones
and checked them and they have varying
measurements some of them are 10
something like that which I guess would
be these seven volt ones and then this
one was much higher it was like 40 or
something it moved around a little bit
but this one is completely open so I'm
gon to see in my great stash of
bulbs tubes do I have a 35 Z3 I'll bet I
probably
do I found one I had one just
one but I tested it and it is not uh
open but this one is now an interesting
thing I hated that I had to do this
originally was a 35
Y3 this isn't labeled anymore you can't
tell what it is but it must be a 35 y4
because it has an extra pin on
it so these two are the
heater and then this one is the anode or
cathode and this one is the anode or
cathode this extra pin which is pin four
one so you start at the dot and you you
count counter you count clockwise one
two three four pin 4 is just an extra
pin that they added in so that um
there's a tap for a light bulb right but
if this is you know this is an old
radio this is like
a 1942 was it
1942 um so they just wired it up
differently they just wired it across
that
resistor
um so but here's the problem on the
bottom of the radio they are using that
pin as like a tie off point so what they
would do a lot of times is if the if it
doesn't use all eight pins or whatever
if like pin four isn't used you would
just use that to jump jump uh Junction
some wires and jumper some stuff around
because you know there's no pin there
well that's fine until you put a
substitute tube in it that has an extra
pin on it so 35 Y3 is what's supposed to
be in there but 35 y4 appears to be what
was in there but this pin has stuff
soldered to the bottom of it they're
just using it as a as a junction so
you're not really it's not a good
substitution you're you're you're
running a voltage into a spot that's not
supposed to have a voltage because
they're just jump ring wires there they
may have done it in such a way that it
worked fine I don't know but not wanting
to repeat what I see as a mistake I cut
the pen off of my 35 y4 so I didn't have
a 35
Y3 I'm sorry 35 Z3 I had a 35
Z4 which is the updated version with the
extra pen that must be what this is too
they must have already done that this is
a Sylvania uh this is a fil code radio
apparent you would think originally they
um probably had fil Co tubes in it so
tube's probably been replaced at some
point so anyway I cut the pin off and
now we're ready to try it again so we're
going to turn it
on and we're going to watch our amps
over here to see if anything crazy
happens right so I'm at zero volts let's
try it I didn't measure them but I
measured all of all of them before and
they were all fine and then I measured
this one out of the radio so they should
all be linked together
now now we won't get any sound or
anything half of the radio is not even
hooked up we're just trying to see if we
can get glow out of the
tubes 20 volts yep
look I already got it on the
light so we got some glow on the bulb
need to watch that to make sure it
doesn't go
crazy it is going up a little bit but
nothing
crazy I'm watching the
meter okay I think that's about 120
volts and yeah we've
got filament glow if you've got one I
guess you must have all five or it
wouldn't it wouldn't be able to do that
okay so we apparently have the string
working you can kind of
tell I can see it a little
bit um so next thing I want to do is I
want to check the voltage that we're
getting out of the
rectifier so let me turn it back off
turn it up on its end so that we can get
to that capacitor and we should be able
to check it across
that okay so I was able to check
it and we are getting I have no clue if
this is correct we are getting
176
volts right there out of the rectifier
so we've got about 120 going
in and we're getting 176 out then it
runs through this field coil
and it should have 95 on the other
side so I'm sure there can be math done
to figure that out
but I think that sounds about right let
me see if I can figure out if I can
figure out what the DC voltage should be
coming out of the rectifier if 120 is
going
in all right so I checked our input
voltage is a little high it was like 128
I turned it down to 120 um and then this
lowered to about 160 8 so and then I
looked online and people are saying that
usually when you have 120 going in you
got about 170 coming
out so I think we're right on the money
um so I think what we've done is we've
gotten this figured
out and this figured out we've
discovered that our field coil is messed
up our speaker can't be used because of
that um and I think a lot of this is
going to be all right but uh that's
where we're at right now we're up to
here everything's cool up to here and
and we're not blowing fuses or anything
and we've removed almost all of the um
wiring that we need to so I need to I
think I'm just going to use a resistor
for it they say if you do this it can
add some noise but I don't really know
how to get a the right choke for this um
to replace that so I think I'm just
going to use this and see what kind of
noise we've got they're saying online
that if you up these capacitors it'll
filter out more of the noise but we'll
see how it is I'm not really that
worried about it usually uh if things
are noisy where there's a little hum
going on or a little buzz in the
background it doesn't bother me at all
but we'll see we can always adjust it
later too so we got to add this in and
then check what happens afterwards and
then we've got to get our output
Transformer back on with a well probably
a different one with a um a correct
speaker big
job but I feel good that we got the uh
the string
working and we got the we figured out
the rectifier tube was bad and uh worked
through that so that's where we're at so
far oh and by the way the amp gauge went
up to 02 that was as high as it ever
went which again it's probably about
right all right folks so there you go
this has been this week's amateur repair
time join us back next time when we'll
uh we'll get farther into it I I think
I'm going to sneak in a uh we haven't
finished this and we've been working on
for quite a while I also still have my
Majestic radio over here that we uh need
to finish
up uh so we've got two unfinished
projects here but my buddy Dennis wants
us to work on an eight track player that
he's trying to put in his in his car so
we might do that and take a little break
from this work on the eight trck player
and then uh
come back to this or come back to the
Majestics we'll see so if anybody's got
any ideas how would you do it because uh
most of you certainly probably know more
about it than I do um so uh what's your
opinion can we get away with this sand
resistor here or do we have to find a
choke um but leave your comments down
below let us know what you think and we
will see you next week hey make sure to
check out my brother Donnie if you don't
know about him my brother has his own
channel here on YouTube uh where we
lately have been doing a lot of work on
mobile homes and we've even been touring
like some new mobile homes and things
like that a fun time is had by all so go
check out his channel uh and if you like
watching me Tinker with these old radios
and I don't know what I'm doing check
out this video where I did something
similar a while back we'll see you on
the next one
