Keep your Freeze Dryer Vacuum Pump as clean as the day you got it and get rid of the messy oil changes after every batch with a DIY Filter/Dryer vacuum pump automatic oil filter.
This system keeps the inside of your vacuum pump clean and the oil crystal clear and looking just like NEW. No gunk or crud buildup. No rust and contaminants, just crystal clear oil running through your pump.
With this system in place I have added less than 1/4 cup of new oil to the system in over a year. The oil is crystal clean and the pump pulls vacuum faster than it did when it was new and our machine runs 24/7 from mid July through Jan 30 and the only downtime for the vacuum pump is defrost and freeze down.
We pre-freeze most of our produce so the freeze down is short, about 1 hour compared to the standard Harvest Right 8 hours freeze down.
I run this oil filtration and water separator system from before the pump kicks on and then for 2-3 hours after the pump and the freeze drying cycle is complete. This helps the pump and oil cool down and allows the filter to condense all of the micro water particles that are in the oil, keeping them out of the pump itself.
PLEASE SUBSCRIBE - It helps me a TON.
NOTE: I use a special vacuum pump oil made for Dairy Milking Machines that deal with a lot of moisture. It has some additives that help keep the oil clean and it gives your machine better vacuum and a longer lifespan. Find a link to this oil on my website below.
Some of the items listed below are NOT on my website but are readily available at your local hardware store.
THE FULL PARTS LIST 1- Heavy Duty Filter Mounting Base = WIX 24770 abt-$31.53 1- Fuel Filter & Water Separator = FRAM PS3712 abt-$14.04 1- JDMSPEED Universal 12v Heavy Duty Electric Fuel Pump abt-$11.84 1- ICstation Timer Relay, DC 12v abt-$11.99 1- 1/2" pvc slip female to 1/2" thread female coupler 1- 1/2" pvc slip tee 1- 1/2" pvc x 2" pipe (length may differ for your installation) 2- 1/2" pvc x 6" pipe (length may differ for your installation) 1- 1/2" pvc x 8" pipe (length may differ for your installation) 1- 1/2" pvc slip Union Coupling 1- 1/4" brass pipe x 6" 1- 1/4" brass pipe x close thread 1- 1/4" brass elbow - male to female 1- 1/4" brass tee 2- 1/4" brass male pipe to 1/4" hose barb 1- 1/4" brass female to female gate valve 8- 1/4" hose clamps or equivalent 1- 3/8" x 3/8" x 1/4" brass tee FFF (the 1/4" is the stem side of the tee) 1- 3/8" brass close nipple 2- 12vdc wire harness couplers to allow removal of electrical parts for replacement 1- 12vdc rocker switch, lighted or unlighted as you prefer
Misc 1- Roll of Teflon Tape 12vdc wire (length to fit your installation) 1/4" clear vinyl tubing (length to fit your installation) A container with a lid that you can make a 1" hole in the top to accommodate the pvc overflow pipe Mounting hardware & bolts or screws for the fuel pump and Filter Mounting Base (NOTE: the mounting base and full oil filter are heavy so secure the base securely) Tools as needed
My Social Links: YouTube.com/@CaptainWingnut Facebook.com/CaptWingnut Facebook.com/CougarRidgeRanch ganjingworld.com/s/pEngrr1BzX Instagram.com/CaptainWingnut Rumble = CougarRidgeRanch SnapChat = TheCaptWingnut TikTok = CaptainWingnut Truth Social = @CaptWingnut X.com/BWardleCW
As Always: This is what "I do", it's up to you to ALWAYS use your own research & more importantly...common sense. I welcome your comments & questions and I do my best to answer as many as I physically can If you decide to post a comment, be nice & post an educated, intelligent comment If YouTube doesn't, I may delete and mute/block any inappropriate, rude, mean, frivolous, unintelligent (stupid) or irrelevant posts or posters CaptWingnut
MUSIC FROM YOUTUBE LIBRARY: Russian Dance - Joey Pecoraro Positive Fuse - French Fuse Nothing On Me - Patrick Patrikios
Hi, Brad Wardle callsign Captain Wingnut from Cougar Ridge Ranch. Hi in the Uintah Mountains
of Eastern Utah. Today I'm gonna let you take a trip and be a fly on the wall. Watch what I do.
Yeah, Harvest Drite freeze dryer and the pump. And the pump, oh it's my nemesis.
Every time you finish a batch you gotta dump the oil and you dump the oil into this
fancy strainer thing and you gotta replace the filter and you gotta do all these funky things
to it and every 10 or 20 batches you gotta pull this off and clean it out because it's full of
gunk. I gotta come up with something different. So I've been doing a little research and a little
testing and I'm gonna let you come along with me for the ride to see what I do. I'm going to build
an automatic pump system for this baby so I don't have to take this apart every single time. See,
we start running our freeze dryer about 24-7 from about the middle of July until probably the end
of January with all of the garden and everything that we grow and get here. We're freeze drying all
the time and it's got to be able to run and it goes down and I gotta do the oil and oh it's just
a pain. It just can't happen. So I'm gonna set up an automatic oil filtration system for this
and I'm gonna let you come along for the ride. Let's go!
So here is why I'm building an auto filtration system. I've broken the pump down and put the
auto filtration system in. It has done two batches. Two batches since I replaced the filter
in another video and that's the scum and crud that you get and it's new oil but that's what
happens when when you're freeze drying in the pump. It just fills up with goop. So that's why
I'm building a filtration system because this goop is unbelievable crap. Can I say that? All right.
Before I forget, don't forget to subscribe and click the notify button so that you know when
I release new videos. First let me say that the time between shooting this footage and making
this video has been over a year and this baby works wonderfully. I opened the pump after 10
batches and it looks just like new. Shiny, clean, no gunk, no soot, no yuck. Okay so here we have
the parts that you're going to need to build the automatic oil filter and water separator.
From left to right we have a box of a quarter inch vinyl hose and that is a box. You probably
don't need a box. You can just go to the hardware store and measure what you need. Buy it that way
but I have a box on hand because I have lots of projects going. The next thing is the diesel
fuel filter water separator. Then we have some 12 volt wire, some connectors, crimpers,
the cheapy overflow reservoir, the fuel pump, a quarter inch by eight inch brass pipe. That goes
in the bottom of the pump where the original drain plug is now. Quarter inch brass tee,
quarter inch brass male pipe to a quarter inch hose barb, quarter inch brass closed nipple,
and a quarter inch brass female to female gate valve, quarter inch male to female,
and a half inch male to female pvc coupler decoupler, and then there's miscellaneous pvc
pipe and tees. You can look in the description for the details of all of the parts. Next there's a
120 volt ac to 12 volt dc 4 amp power supply, a timer, the electrical plugs, filter mounting base,
three-eighths by three-eighths by quarter brass tee, female female female, and special note here
the quarter inch part is the stem side of the tee. You'll want to make sure that's what you get.
And then there's a three-eighths brass closed nipple and some quarter inch hose clamps. All
these items are listed in the description and you can find them on my website that's listed in the
description as well. So here I'm putting teflon tape on all of the fittings, the pipe fittings,
getting them ready to put them all together. And it takes a little bit of time and now I'm
putting them together. All right now we've jumped into the completed assembly and I'm going to leave
it on this frame just for a moment so that you can get a good look at how it's all put together.
And then let's get on to the next part. So now the pump is all put together ready to go and I
need to install it on the machine. And so I'm just putting the filters and the barbs and everything
here getting them in place. And I decided I was going to mount it right on the bottom of the wood
that the freeze dryer is sitting on on my stand. But I did decide that I was going to put the timer
and the switch right on the face of the freeze dryer. Now if you do this you'll void the warranty
of the freeze dryer but ours is way out of warranty anyway so it didn't matter.
And then all my switches are right there with everything else on the freeze dryer. So doing a
little chopping, a little drilling, some pilot holes and get it all cut in. So I'm just going
to let you watch me finish putting this together for about the next 30 seconds. So here it is
complete. Let me show you what it looks like. Huh yeah goodbye to scuzzy moto here. Holy smoke
that's just that's just three batches right there. Oh yeah yeah that's ugly. So here it is.
Here's the pump and I use the I use the cap that used to be in the pump and that just goes right
back on top right here when you're done. You gotta try this when you're looking at the camera
left-handed. Okay so there it is and you can see the clear glass. Look at my
other video and you'll see my little short video on how to clean that glass real easy.
The the pipe comes out the bottom comes to this t-fitting that's going to pull out of the bottom
of the pump up and it's going to go into the filter and this is a water separator filter so
the water will pile up in here and I can just drain the water right out of there
and it's filtering the oil. This is a this is a diesel fuel filter so it's it's very good.
Then it comes out of here and it's pulled by the electric fuel pump and that comes back down in
and goes back in to the top through this three-eighths t back into the reservoir.
I'm going to turn it on and show you what it looks like.
So the timer here shows that it's timing down from 10 seconds and it's going to run for 240 seconds
I've just got that set to run so it'll keep running and you can see that it's pulling air
through the pipe through the filter it's purging the air this first time I run it
it's camera focus I'm a little too close there there we go so the oil is coming out of the bottom
up through the filter in and then out it's being pulled by the fuel pump and it's being put right
back in just uses a little just a little computer power supply it's a four amp power supply
and 12 volts and so that just plugs in and then I had this little timer that I had
bought for another solution another project and I decided to use it because the pump doesn't
need to run all the time so I'll probably set it to run 60 seconds on 60 seconds off
when uh when I uh when the pump actually comes on in this in the drying cycles so that's how it
works I actually I built this stand for the freeze dryer so that everything is up and out of the way
and you can see inside here I need to get you a light you can see inside here my wiring there we
go and that's just the timer over there with the switch and it just comes out the bottom
and works right there yeah cool now listen if you do this you're going to void the warranty on
your pump if your pump is still under warranty and just keep in mind that manufacturers look
for anything to void the warranty anything for them not to be responsible even though this is
going to preserve this pump and give this pump a greater life they would void the warranty
it's out of warranty anyway so that doesn't matter and I put the timer in the front of the
in the freeze dryer and that would void the warranty there too but it's out of warranty
we've had it for I don't know four or five years and it just runs and runs and runs it's it's a
very very very good machine but you can see that I put the pipe coming down so that it the vacuum
hose coming down and then it comes around through here I actually ordered another one from harvest
right so that I could basically connect them together and have a little more room and it
comes up and goes over and down to the pump so that's that's how to make yourself an oil
an automatic oil filtration system I'll put all of the information
in the description if you want to go to cougaridgeranch.com I'll put I'll put in the
parts list where I got all of these parts and and I'm sure I can figure out where I got this
and put it up for you you can see that it's got 24 seconds left then it's going to rest for 10
seconds and it'll just come on again I've just I've just got it running for 240 seconds just to
make sure that it purges out all of the air and I don't see any air coming through the pipes anymore
everything is purged everything is full my level is a little bit low I'll have to put it on the
timer just shut off and it's timing down it's coming to three two one and it's gonna go again
so there it goes again I'm just gonna let it run for a couple of cycles just to make sure that
everything's working you can see I put a valve and a little elbow here just so I can drain the
whole system if I want it doesn't give me much room from for the floor that's okay I could always
lift it up and put something else under it now one of the things that you saw when I had all the
parts out at the table is I had this funky little jar this is just a jar from the dollar store
and it's kind of cheap the lid shattered when I was making the hole in the top but
I just used a half inch pvc with this coupler right here so that I can uncouple it and and
move the pump around but what happens is when when the pump is warm oh there comes some air back
when the pump is is hot I've had some issues where the the power has gone out on us
in the house and then it comes back on and when it comes back on the pump kicks right back in
and when the pump is hot like that it blows oil it blows oil right up this tube and there's they
put a little filter thing on but it just blows oil all over so when you have this filter system
you're going to be able to have more oil in the reservoir than normal because as this filter
starts to fill up with water it's going to have more volume in the system and so this
this pump reservoir could get a little higher so I built this just so that I could
keep the oil from spraying all over another tip is I put it on a little cake pan I just went down
down to the second hand store and got this old burned up cake pan and put it on here just so if
the pump has a leak and it has the back seal look up my other video replacing the back seal
the back seal goes out occasionally about every two or three years and then as the oil comes out
it catches in this pan and it doesn't go all over the floor and everywhere else
so the first thing I do is I give myself a little paper towel and a just an old pill bottle
it doesn't have to be terribly big and then I put a little crack on the open of the
nut here at the bottom the drain and then you have to this the system is sealed so there's no
air that can get into this and so you have to kind of loosen the oil filter itself so a little
air you can see the air going in because it's dripping down back in the hose here to the
reservoir that lets me know that a little air is going in and then I can open this
drain and there comes the water see the water coming out and as it usually fills when the
comes to the end just before the oil starts to drip the water really stops and I can sometimes
get a little shake and loosen it a little bit and but the oil is thicker than the water and
so it kind of gets stuck in the little in the little opening here and most of the water will
come out you can see it's still still dribbling just a little bit if I open it a lot I'll start
to get oil there's a little bit of oil coming a little bit of oil there so then I'll just
tighten this back up and I'll tighten everything back up wipe it all down a little bit put a paper
towel down here underneath it and there's the there's the water and you can see a little bit
of the green dairy pump oil in there and I turn the pump back on and let it just cycle a little
bit longer so that I know that it's all clean and pretty and dump out the water and that's it
simple as that you don't have to take the pump apart the pump is just absolutely crystal clean
inside that's kind of how I run the freeze dryer I'm going to put the side back on here
and get it back in business it needs to it needs to be going 24-7 right now we've got a ton of
produce from the garden from this summer so thanks for watching Brad callsign Captain Wingnut from
Cougar Ridge Ranch 7,000 feet up in the High Uintah Mountains appreciate you watching
ciao that's cowboy talk right