829. Throwing a Large Lidded Moon Jar with Hsin-Chuen Lin 林新春 蓋圓瓶拉坯示範

Hsinchuen Lin
205 followers
11 Video Views·Dec 2, 2024
The tools and finished ceramic work can be purchased on my shops:
For customers living in the US, you might find it cheaper if order directly from My SquareSpace shop
https://sawfish-endive-kgks.squarespace.com/shop
For outside US customers, order from my Etsy shops
https://www.etsy.com/shop/Hsinchuen
https://www.etsy.com/shop/HsinCeramics
http://www.etsy.com/shop/hsintools
To watch more of my YouTube videos, please visit my channel:
http://www.youtube.com/@hsinchuen
To learn more information, please visit my Website:
www.mypots.net
Instagram: @hsinchuenlin
Facebook page: Hsin-Chuen Lin Ceramics
Pinterest: @hsinchuen6518
okay uh what I did was try to Center the
skin of the clay just the outer part
instead of pushing the lar mon clay and
calling up and calling down I'm just
kind of moving around the skin of clay
so it's very
effess even you have a large amount of a
clay
so what am I doing is try to use my both
hand Goen in there and then push down
slightly bump it this part here together
so kind of open it up and with my thumb
outside to control the wall so that when
I'm drilling
it the wall still under my control of my
thumb on the out to compress
it and I take it all the way until the
right thickness which is somewhere
around half of in to 3/4 inch I like to
have my foot slightly taller so that's
the thickness I usually leave
I'm using my tip of my finger pad to
compress the
floor and go directly from the center to
my right
slowly until it reach the
corner and some people do find this way
is hard so actually
I I designed this tool for the FL
compression which is very easy and very
efficient to do all you need to do is
using this part here to compress from
from the center and then gradually push
it out to the corner and with your both
hand hold it very steady and compress
from
the center and move it
to my
right so this is the tool for
compressing the floor it's very
efficient and very good to work
with so that you always have a very good
corner there instead of leaving too much
clay which might be a little bit too
heavy because you have too much clay
inside
corner and now I'm starting lift the
clay pinch the clay just using my left
thumb and the fingers and grab the clay
and then pull it
up and the outside hand slightly helping
my my thumb to strength and then pinch
the
clay and lift it up
it's easier to P your cylinder total
when it's narrower so after my initial
lifting I usually color my clay to get
it little bit
narrower and also I bring the corner of
the clay inward
bring it
in using
my right fingertip and then pinch
it and then after that squeeze the clay
squeeze the wall and
slowly move it
up and remove the slip up my finger
tips and put it
inside and grab that slip I just put in
and then coat it on the inside of the
wall I'm going to pinch in further so
that the base will be narrower
I do one more lifting from the
inside push the wall against my palm
outside and inside hand is
lifting okay focus on this part here and
lift the thin it down
further put the slip back to work put it
inside in the corner and then brush it
over all the way to the
top do it one more time
and outside is easy just tun my hand in
the water and brush
it bring the corner clay in
further color the clay up a bit
put the slip back to
work slightly compress the
rim for
all right so I try to get it as tall as
I can before I stretch it out to form
the shape slow down the speed the wheel
a little
bit this wheel is very uh good for
contouring the slow speed and also very
quiet the name of this wheel is called
bth
bth for
and as you can see I always keep my rim
slightly thicker so it'll hold the shap
better if you stretch it too thin the
rim usually becomes wobbly easily so
always make sure that the rim you you
leave it slightly thicker so it hold the
head a a little bit better
so usually when you stretching it out
especially like
the mja shape the shoulder here is
somehow slightly wobbly so what I did is
in my hand
inside the finger is kind of spread it
out so you will have more support can
see that my finger is kind of spread out
on the inner side here so I have more
area to support it while I'm stretching
it out
this is my hand inside
right so I'm going to make a little
jar I will put a gallery here on the
body and also put a gallery on my lid
so the tool I use is M the number one
number one wooden rep for nice 90°
corner so you will be able to push the
gallery with a fingers underneath inside
to support it
to use my number
17 to get the access CLEP from the
corner remember when
you cut the clay the clay coming up from
the tool remove it otherwise it might
stick back to
the side of the
pot okay so this is the final piece and
then I need to
measure I need to measure the size of
the lid
okay that's
good then I remove from the wheel
head I usually will wi it up later so if
you don't see me wi it up now I wi it up
maybe a couple hours later
so you have watch me you're doing the
little part many many times if you
follow my videos when throw upside down
LD meaning I'm putting a gallery on my
lid I usually Center my clay into a the
shape looks like a dut
dut and open a shallow shape of a
bow while keeping the rim the outside
part slightly thicker cuz you are going
to put the gallery
there I'm using that curve of my thumb
to squeeze it
on the inner
part so with the the two fingertips
pinch the thicker Rim I'm using one of
my finger you can use the thumb or your
index finger to squeeze a little nutch
here a little indentation there so that
that there will be your gallery
and then I bring back my number
one wooden rib the triangle
shape finger support on the inside and
then just squeeze using the corner of
my triangular rib and make sure I double
check the width of the rim this part
here
needs to go into the gallery of my body
so this is slightly too wide so I will
chop it off but after I clean up
everything I will do that
I'm getting my number
10 bra sh TP knife to chop it
off I like this knife to cut the rim is
it's compared with the um the needle
this is much
thinner thinner
blade and the less
resistance easier much easier to cut
all right so that's it
and use my number 17 wet
trimmer all right so that's the uh lid
for my one shap cover
jar okay thanks for watching and uh I
will see you in my next triming video
[Music]
[Music]
