43 Video Views·Oct 29, 2024 #DadHowDoI #RobKenney #HowTo How to Install a Ceiling Fan - Sponsored by Hunter Fan.
Here is a link to the Dempsey Fan that is in this video;
https://www.hunterfan.com/products/ceiling-fans-dempsey-low-profile-with-light-44-inch-fam773?variant=34520205033604
Disclaimer:
This video is produced by “Dad, how do I?” and it is provided for informational, educational, entertainment purposes only. Some of these projects, materials, and techniques may not be appropriate for all ages or skill levels. “Dad, how do I?” does not make any claims of the safety of the projects, techniques, or resources listed on this site including this video, and will not take responsibility of what you do with the information provided by this site. Viewers must be aware by doing DIY projects on their homes or vehicles, they are doing it at their own risk and “Dad, how do I?” cannot be held liable if they cause any damage to their homes or vehicles. “Dad, how do I?” assumes no liability for property damage or personal injury incurred as a result of any of the information contained in this video. Use this information at your own risk. “Dad, how do I?” recommends safe practices when working with tools seen or implied in this or any other video on my channel. Due to factors beyond the control of “Dad, how do I?“, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not “Dad, how do I?”.
Subscribe: https://rb.gy/rdm2sl | Make sure to enable ALL push notifications!
Watch the latest videos: https://rb.gy/rdm2sl
Watch More Dad how do I?:
Dad Chats: https://rb.gy/rdm2sl
Tool Tuesday: https://rb.gy/rdm2sl
Most Popular: https://rb.gy/rdm2sl
Follow Dad how do I?:
TikTok: https://www.tiktok.com/@therealdadhowdoi?lang=en
Facebook: https://www.facebook.com/dadhowdoi
Instagram: https://www.instagram.com/dadhowdoi/
Affiliate link to my book;
My Book: https://amzn.to/3idKKzq
About Dad How Do I: Welcome to the official "Dad, how do I?" YouTube Channel! Here you will find "How To" videos by a dad who has raised 2 adults (and we still talk). I will do my best to provide useful , practical content to many basic tasks that everyone should know how to do. On this channel, you will find a variety of content like How To's, Story times, Dad Chats, and more! Make sure to subscribe and enable ALL notifications!
#DadHowDoI #RobKenney #HowTo #HunterFan
hey kids so today i'm going to show you
how to install
a fan a ceiling fan uh and i
uh hunter fan actually reached out to me
wanting to sponsor this video um this is
something people have asked me for and
so i thought it's a perfect opportunity
to to work with hunter
uh you know they like what i'm doing
with my channel and so they wanted to
support me
and so and it made sense so uh
so installing a fan really you know it's
really not all that hard as long as you
just pay attention to what you're doing
and take it in baby steps that's what i
try to teach on my channels to
you know just slow things down and and
break it down into small steps so so you
can figure it out
um you know hunter fans is a quality fan
they've been around for 135 years
uh they're designed to be quiet and to
be wobble free
if if you've ever seen a fan maybe a
cheaper fan and
when it gets going fast it starts
wobbling which can be a little bit scary
uh these are meant to not do that so um
you know so first you'll need to pick
out your fan
uh you can go to www.hunterfan.com
and you can look at their complete
selection or they're also available in
lowe's and other
and other hardware stores and also have
a
link in the description of this video
to the fan that i'm using i pick out
this particular fan because it's
low profile so it sits closer to the
ceiling
so because if it got down too far you
know i'm fairly tall that wouldn't be
good right so you need to make sure that
it's
it's up there higher or they make some
that you know you can get a down rod
to make it longer so if you have a high
ceiling
then the fan can come down a little bit
lower so
um anyway so before we do this i have a
dad joke for you of course right
so uh you know i was gonna tell you a
joke about ceiling fans
but it was over your head ah so anyway
let's get started
all right so i thought i'd show you this
this is just this is disconnected right
there's nothing there's no power running
to it or anything but this is basically
what you're gonna this is what's behind
the the ceiling this is
see these nails here these are actually
pounded into a stud
for the most part you know obviously
it's going to vary depending on what
your setup is but basically you're going
to have a junction box like that
in the ceiling where the light attaches
okay that we're going to attach the fan
to
and then sticking out of that again this
is a basic real i'm showing you real
basic you got a black wire
and then you got a white wire and then
you got the ground
that's what that is okay and basically
um we're gonna
when we open up that light uh when we
remove the light we're gonna have three
wires sticking down just like that right
and so first thing we need to do is cut
the power right we want the power off
and then we're going to end up removing
our light and we're going to have this
sticking down
that we're going to um attach the we're
going to detach the existing light
and then we're going to attach that fan
to okay so
i thought i'd show you that first just
so you understand so you know what to
expect and what's behind there
uh before we take it apart all right
okay so this is the light i'm going to
remove
like i said i really like this light i
actually replaced it about a year ago
but i'm gonna go ahead and pull it down
and we're gonna replace it with a fan
and then like i said i'll move this
light to somewhere else because i really
like it i don't wanna
donate it i want to hang on to it so uh
anyway i'll show you what that looks
like we just got to start taking it
apart you know there's going to be
um like i said it's it's different for
every
every light you know it's going to be a
little bit different i'll probably start
here and unscrew that but first i still
haven't cut the power yet
um so before i start doing that start
messing around
right make sure to cut the power but uh
so we're just going to start taking it
apart and so we can get back to this
part
right where that that um junction box is
sticking out of the ceiling that we're
gonna uh attach the fan to
okay so i'm out at my junction box
and i know that number nine this is the
one
for that i need to flip off it's on
right now i just need to flip it off and
then that will cut the power to that
light so i just wanted to show you this
i think i showed it in a previous video
but wanted to walk you through that
again you got to go to your panel and
you got to figure out
uh which circuit it's on
um and i do have a circuit breaker
detective video
so you could refer to that to figure out
which circuits it's on if you need to
but i already know that this one's nine
so i'm turning that off
right so just flip it to the left we'll
go check and make sure that light's off
now
okay so the light is off and i'm just
going to double check with the switch
um i'll try to make it loud so you can
hear it yeah so there's nothing
there's no power running to that so i'm
safe to go ahead and start disassembling
this
and um yeah let me just get into it
um i think this just was like this
and again this is going to vary
depending on what uh
what your lamp looks like so i couldn't
remember what this is like
so let's just it had uh here that's
gonna stay there
so it just had these this little uh
screw on the top
um that was just screwed up onto there
and then now it's got another nut that
needs to come off
so i'm gonna work on that
okay so i moved the camera a little bit
so you can maybe see these uh these are
caps with that are threaded that are
gonna go right over the top of these
uh these bolts that are sticking down
that that's what's holding it up there
so i'm gonna remove those
um let's see here so you gotta unscrew
that i'll show you what that looks like
when i get it off here
yeah so it just looks like that and it's
got threads in
in it right so that's what's holding
that up and then there's one on the
other
side too try to get to it
okay and now that should just come down
there we go
okay so we got the wires
coming out here so there's a black wire
there's the ground and here's the white
wire
like we talked like i showed you at the
beginning okay got a black wire
a white wire and a ground pretty
straightforward so
um i always like to add a little bit of
electrical tape you don't have to it
doesn't ask you to
i just always it's like one less one
more thing to kind of hold those wires
together
okay so all i'm going to do now is i'm
just going to unscrew these caps
okay and that's just what holds those
guys together
uh here we go so basically that's all
that is that thing's just screwed right
on there and it screws the wires
together okay
so now that's that okay
and then this one here just unscrew it
okay and then that sets that free so now
we've got
these two free and it's still being held
up by this
one wire here it's being held by the
ground
um this thing isn't too heavy but i
gotta
i'm gonna have to figure out how that's
attached there let's see how did i
attach that
so we can undo this maybe this is all we
need to do
nope okay i think it's wrapped around
i did a pretty good job wrapping this
guy together so let's see
and again this is gonna vary so it's
gonna whoa there we go good thing i had
a hold up
so that set it free okay so now we got
we have our black wire our white wire
and then we have our ground
hanging out and hanging down right here
all right
so the first piece of advice i would
give you if you're ever
building anything that comes in a kit
like this where it's got
all kinds of different pieces is you lay
everything out
lay everything out first and then
most instruction manuals will have
a parts list and then you just walk
through
and see what each piece does and it'll
also help you when you're
you know as you're putting the fan up to
go oh okay i recognize that piece
because i already had some familiarity
with it right
and then that uh hunter actually does it
where they have little baggies
with each uh you know sets of screws or
whatever you're going to need
so that it just makes it that much
easier to identify it
and then you know even even before you
get started just
kind of read through this it's not that
big of a pamphlet uh
so you just kind of walk through it and
just kind of see what to expect oh okay
that's that and then
that's that right so just make your
install go so much easier and then you
know there could be a part that's
missing and you're frustrated you're
like ah
where is that thing it's just best to
just check everything make sure that
everything's there before you get
started
all right so the first thing we need to
do is install the bracket
and so this is what the bracket looks
like on this particular one
and see these little rubber feet here
that actually goes up against
the ceiling to kind of give it some
stability right it's got it's a little
bit of
flex to it so it um mounts up there
and kind of keeps it from that probably
helps with a little bit of the wobble
so basically what we need to do is
you're just going to feed these wires
these are all off right i'm going to
feed these wires through here
like that and then i'm going to secure
that like that
okay so you got your white your white
wire your black wire and your ground
right here okay just like that and i'm
going to secure that so that's what i'm
going to do right now
basically with just a couple screws so
the way this fan
is and the instructions try to make it
kind of easy for you
see how it's got that star on there it
tells you which bag you're looking for
and
in this particular bag it had these wood
screws
okay that's what it came with and then
so it tells you
you can either use these um to get into
a stud
which i always like to get into a stud
uh
or um you can actually the screws that
came
with your junction box that's what they
call that that junction box up there
right
um you can screw these things into there
so
um what i'm probably going to do i'm
going to get
one into the actual junction box and
then one into a stud
okay because i know there's a stud right
here and this gives me all kinds of
options there's lots of slots on this
and so i can uh
i can do it that way so that's what i'm
gonna do
okay so this one is what's considered
the machine screw the one that's going
into the
the actual outlet box okay
okay that's that one and then
i actually you know you can use the
screws that came with it i really like
these screws so this is the screw that
i'm going to use but you could
the ones that came with it were these
right so
i'm just gonna use this one and i'm
gonna get it into a stud
out here on the on this side
okay that's nice and solid that's not
going anywhere
right so you just want to make sure
because if you're if your junction box
is wobbly
that's not going to be a good thing
right you want to make sure that that's
nice and secure
okay okay the next thing it says to do
is
is this at the bottom here i'm rather
than read it all i'm going to just walk
you through that
you want to take this feed it through
here
and you have these holes here and
they're going to line up with these
holes okay
i'm going to put that housing on right
there
okay now those holes are still there and
then we put this on this is next
that's what that ring is and we just
basically put that
right there like that and then this is
the last piece
and you got the three holes again right
so we're gonna feed that through
just like that
okay that's that step and i just want to
keep that like that and then i move on
to the next one
and i'm going to put some screws into
there to to hold that
okay so when you put this piece on make
sure
you see how you got the three holes on
the outside and then you got this
this one hole over here by itself make
sure that lines up with this
right because if you put this on here
and if
that hole is not there you're gonna be
spinning this thing around you're not
going to be able to get that
that last little ground hole ground
screw in there okay
so let's go ahead and we tighten this up
tighten up on the long ones but don't
tighten it all the way just get it
started
okay
part way down let's even um we have this
little shorter screw that actually is
the ground
let's get that that guy in there and
that'll help everything line up
i'll show you a close-up of this in just
a second
my hand would be in the way for you
right now if i try to show it right now
but okay and then this last guy here
actually this is the last guy
okay so those are all loosely in there
let me just tighten them down
nice and easy
we'll leave the ground one loose a
little bit because i'm guessing we're
going to attach
a ground wire to that
okay so that's what that looks like
inside there
i just attached those
okay i actually have i cut my own little
ground wire here that i'm gonna put on
that ground
okay on that ground screw and then we're
just gonna go ahead and screw that down
and
okay and then we'll be able to screw all
the grounds together
okay so this particular fan actually has
a remote
so you may or may not have that but
basically you just gotta piece it
together so these
two are gonna go to
uh the wiring in my house okay
and then these are gonna connect to the
fan
okay and so basically it tells me
and so i just read the instructions blue
goes to blue that sure makes it easy
right blue goes to blue so basically you
just take these two wires like this
and you spin them together and then you
use the cap
and then you spin that together okay
just take that
spin it all together make sure you get a
good connection there okay
and then the next one is a little bit uh
tricky because you've got you've got a
yellow one and there's no yellow
right so what are we gonna do we're
actually gonna it tells you
to connect the yellow wire to the black
wire
okay so you actually need to take a look
at that
we're going to connect the yellow to the
black okay
we're going to get a good connection
there and then we spin those together
okay
okay so now we're ready to go
and that's just going to go down inside
there like that
okay and then we'll be able to connect
let's put these kind of together so that
they're all there
okay and then we'll connect the
the black the white and the ground once
we hang this from the
from the ceiling okay okay so now we're
just gonna take those two holes there
and they're gonna hook onto this side
over here okay now that we got our
our uh receiver hooked up on the inside
let's go ahead and do that
okay so you're getting close now
right so now we need to make sure we
have our
uh our spinnies right
actually i just need one more
okay so that way the ground can attach
so
if you remember we had the white okay
so the white wire we actually had an
extra white wire right
so here's our white wire our white wire
and there's one white wire coming out of
the coming out of the top
right so we're going to spin all those
together
okay so we just take this cap off
remember the power is off so we don't
need to worry about anything there
okay and then we just spin all of these
together we're going to put them all
together like that
and then we just spin them all together
so these my uh old
light that was up here this is where
these ones come from so
in the packet these are orange but i'm
just reusing the ones i had
okay spin that together nice and good
okay
that's that and then now we have the
black wire
right and then we're gonna have the
ground
too so let's go ahead and see what we
got for the ground we got the ground
coming from my outlet and then i got a
ground
coming from here okay
coming from my bracket so i'm going to
spin all those together too the ground i
connected in here the
ground here and then the ground that's
uh
coming from my outlet we're going to
spin all those together
okay so the last thing we're going to do
is just spin the black wire with the
black wire
all right we're going to line those up
and spin them together okay
just like that okay and if you want
you know you could add uh if you're
worried about this coming apart
too you could add um a piece of
piece of electrical tape i'll do that
occasionally
just to make sure if i'm worried about
the wires coming undone so you could
just use
just make sure you use a good one
because if you use a bad one
you know they unravel on you so
okay so we're gold and we can just put
all that right back in there
so now this is just going to come up
here and everything's tucked in
i'm just going to go ahead and put in
one screw for now
because i just want to double check
everything make sure we got it
and just get that thing started okay
yeah there we go
[Applause]
i just gotta attach the other you know
there's
three other two right we've already got
one attached now we're just attaching
the one on this side
okay and then there'll be one more on
the other side okay
we're almost there look at that so
and then you get to choose
the color that you want the fan to be
they usually give
you two colors depending on what color
you want facing down for the fan blades
so that's kind of cool and we'll decide
which one of those we want to do
okay so i think we're gonna go ahead and
finish this up
okay and that guy
my uh my ladder and my height is just
uh there's a step if i had to step in
between it'd be perfect but
um all right let me do that other one
and we'll move on
okay so now all we do here is this is a
canopy ring right that we put on there
before and all that does is we just
push it straight on up and it locks into
place
beautiful okay so now like i said you
have a fan blade
this way or this one these are this like
a gray and then like
a light oak and all we're going to do
here is we're just going to slide that
right in there
and then we just put three screws up
inside and we got to do that four
different times
okay so we're attaching the fan blades
and all you do is just
you know you want to attach and just
i say finger tight but maybe not quite
finger tight maybe a little bit tighter
than that you know just
to make sure that it's not going to fall
so we can just use that
and we're going to go ahead and screw
that in
i like to get all the blades up first
and then i'll come back and i'll tighten
all these things
see what we did there all right so when
you're doing these each one it comes
with a washer
and a little mini screw
really a bolt i guess you'd call it but
um yup and then just make sure your
blades are all facing the same way
right you've got your gray facing down
if that's the color you've chosen
right so you're not surprised when you
get down and
go oops i've got
three gray fan blades and one light oak
right so just pay attention to what
you're doing
all right i'll finish this up you get
the hang of this pretty straightforward
you just gotta
just gotta hand tighten those um for now
and then we'll come back and we'll
tighten them all up at the
at the end
just make sure they're secured so they
don't fall
okay want to make sure those are
snug though now
okay okay so we're back to where we
started
okay okay
there you go those are all secured now
we're gonna attach the light
it tells me to do is see these these
holes right here these three holes i'm
gonna put a screw
into two of them okay so
because and then i don't it doesn't it
says it doesn't matter which two
because you'll see in just a second the
the piece that's gonna attach to this
and don't screw them in all the way okay
i'm just gonna screw it in
part way and then the other one's just
gonna fit right on top of it you'll see
or the the piece that we're putting up
here's
okay not all the way okay and then now
i'm going to take this piece here okay
and it's going to feed i got to feed the
wires through here
okay just like that
and then those
the screws that i have i just put the
head over one and where's the other one
just gotta find it there we go and then
i just
twist it to the right
okay i don't think it's quite on there
we go
twist it to the right okay and now i can
just go ahead and attach that
the rest of the way i want to make sure
it's secured
okay and then this one actually let's go
ahead and put another screw in
the one on the opposite side here okay
okay and then we'll finish this one up
okay so that's nice and tight okay
so now in order to attach the light it
says to
put we got to put two
screws in here same thing again don't
tighten them all the way
okay and it says it doesn't matter which
two
and you'll see why
because we'll have
this unit with uh these holes here
right so and we want to
we want to attach this first
so we want to plug that in let's see
make sure you got it facing the right
way
it says aaa so
kind of makes it dummy proof for you
okay so now that's all attached now
we're just gonna put this guy up here
and we put it on that
that screw and twist it a little bit so
that it is where it needs to be
ah come on
okay okay
that's where it wants to go now we're
gonna go ahead and
let's attach the one
okay screw that down let's screw this
one in because we've still got a little
bit of wiggle room let's try to screw it
in
okay nice and tight same thing again
make sure all these are
tight like i said it's good to leave it
loose for a time
but then you want to make sure
everything's tight at the end okay
all right now we're just going to put in
our bulbs
okay make sure that's secure just hand
tight though
right
okay so we're gold in there and then
this last
piece is just gonna go on here
it should be pretty straightforward how
it goes on i think you can see the
notches here so just line up your
notches that
there you go pretty simple
right so there you go we got the
hunter logo there for you all right so
now we just got to turn our power back
on and we'll see
what we got all right so we're just
turning our power back on
there we go let's go check it out
okay this fan is too cool um so it
actually comes with a remote
um and so and it's pretty easy i can
just turn on the light
like that okay pretty cool
turn the light on turn the light off
okay
and then it actually has the different
speeds so i can have
that's one
that's two
that's three or if i want the fan off
and just the light
i hit zero okay so like i said
you know i'm pretty tall so i had to
pick something with a lower
uh profile so make sure you do that make
sure you check that out before you
buy your fan because you don't want it
to be too low
so i'll show you this in just a second
but inside here there's actually a
switch
uh to change the direction of the fan
because
because you want it going a certain way
during winter in a certain way
during summer you want the you know
during the
winter you want the warm air to be
pushing down
but during the summer you want to have
that warm air
uh going up right so that it
keeps it cooler down here so um anyway
i'll show you what that looks like
um and as you can see it's pretty pretty
sleek it's a pretty cool looking uh
looking fan that's why i chose it nice
and clean
and uh yeah so and then you know over
time these get a little dusty so you
just want to come over here and just um
how i normally do it is i'll just take
like one of those lysol wipes and i'll
just wipe it you know get on a ladder
and
and wipe it down good um you know
there's there's actually
uh uh cleaners that are meant to go
right off
the right on it too so and then that'll
take the dust away too because it does
accumulate no matter what you do right
so all right so let me show you that
switch real quick
okay remember how we removed this now we
just need to slide it
pull it off there and then there's that
switch okay
and you just gotta flip it for
winter or flip it for summer okay
okay all right so this is for summer
so this is counterclockwise for the
summer
okay and then we flip that switch to the
right if
for winter okay and then it takes the
takes the warm air and pushes it down
for us
so then you just want to if you want to
mount your uh remote
you just put it here there's just a
little uh
catcher you know a little place where
you can actually keep that remote
or you can keep the remote wherever you
want this way i guess it wouldn't get
lost
right if you just all you do is remove
these
screws here
okay and then you just put this back on
here
okay screw that back in
okay line up the other hole and put it
in
okay that just goes up right over the
top like that and then you just need to
put this guy on here it just slides
right down like this
like that and then the remote just goes
like let's see like that
beautiful
okay so there's my new light and fan in
my space you probably recognize this
space i've done a lot of interviews
here um so it'd be nice to actually have
some air circulation
in in this space uh you know and in all
honesty it probably took me about an
hour and a half to install it i just
went real slow and
you know took my time and i did have
some interruptions while i was doing it
too so i have my dogs
bothering me so uh so anyway i'm sure
that you can
you could do this if you just take it
slow and um yeah
and just be methodical about it the
thing i like about it uh the most
actually
um i mean i love the air circulation but
look how quiet it is
you can't even hear it so uh yeah it's a
very well designed fan so
anyway thank you for watching i hope
this was helpful for you so
um hopefully it gives you the confidence
to try it for yourself and
god bless you