How to Install a Ceiling Fan | Hunter Fan Company #DIYHomeProjects #HomeImprov ementTips #diy #home

TV Electric Fan
2 followers
23 Video Views·Sep 29, 2025
Follow this easy guide for how to install your Hunter ceiling fan with light, with remote, and without the light.
Before you get started installing your Hunter ceiling fan, make sure that the distance between
the bottom edge of your fan blades to the floor is seven feet or more and 30 inches from blade
tip to the nearest wall or obstruction, like cabinet doors. If you're installing it on an
angled ceiling, you'll need a longer downrod. Those are sold separately. Also, measure the
ceiling's angle. If it's greater than 34 degrees, you'll need to buy an angled mounting kit.
Otherwise, you can use the bracket and canopy included in the Hunter box.
When you're ready to start installing your fan, you'll need a few tools.
First things first, turn off the power at the wall switch and the circuit breaker.
There are two options to securing the bracket to the ceiling. Use the machine screws provided with
your existing ceiling fan rated box. You can also use the washers and wood screws included with your
fan to secure the bracket to a structure with an approved electrical box. You'll need to drill
nine 64th inch pilot holes in the support structure to secure the bracket and wood screws.
Remove the pre-installed set screw. Don't lose it. You'll need it later. Feed the wires from the fan
through the downrod. Hand tighten it until it stops, at least four to five turns. Cut the wires
so eight inches remain from the top of the downrod. Then, strip three-eighths of an inch from the top
of the wires. Tighten the set screw with pliers. Do not hand tighten it. Slide the canopy over the
downrod and wires. Pick up the fan by the housing or downrod and place the downrod ball into the
ceiling brackets slot. There are two options to securing the bracket to the ceiling for a low
profile fan. First, you can use the machine screws that come with your ceiling fan rated box to
secure the bracket. You can also use the washers and wood screws included with your fan to secure
the bracket to a structure with an approved electrical box. You'll need to drill nine 64th
inch pilot holes in the support structure to secure the bracket and wood screws.
While holding the wires out of the way, lift the motor assembly and slide the square hanger
into the opening in the ceiling bracket. Make sure the ground wire attached to the square hanger
faces out of the large opening in the ceiling bracket. Use the two locking screws to secure
the motor to the ceiling bracket. When wiring your fan, push the bare metal ends of the wires together.
Slide a wire nut over them, then twist the wire nut clockwise until it's tight. Give it a gentle
pull to make sure none of the wires are loose. To wire a fan that has a remote receiver, you'll need
to use a wire nut to connect the yellow wire from the receiver to the black wire from the fan,
the blue wire from the receiver to the blue wire from the fan, the live wire from the ceiling
to the black wire from the receiver, the common wire from the ceiling to both the white wire from
the receiver and the white wire from the fan, and the three grounding wires coming from the ceiling,
downrod, and hanging bracket. They'll be green, green and yellow striped, or bare copper.
If you have a single wall switch, connect the common wire from the ceiling to the white wire
from the fan, the live wire from the ceiling to the black wire from the fan, and the three
grounding wires coming from the ceiling, downrod, and hanging bracket. They'll be green, green and
yellow striped, or bare copper. Cap the blue wire from the fan. If you have a dual wall switch,
connect the wires the same way, but connect the blue wire from the fan to the light wire
from the ceiling. Tuck the wires into the junction box. Lift the canopy into place so the screw holes
are aligned. Insert and tighten the two canopy screws. Tuck the wires into the junction box.
Raise the motor housing up over the motor and ceiling bracket. Turn the motor housing so the
screw holes align and the indentation in the housing locks into place with the notch in the
ceiling bracket. While holding the motor housing in place, insert and tighten the four motor housing
screws. Insert the grommets into the holes in the blades. Secure each blade to a blade iron with
the respective screws. Lightly attach the blade arms to the motor and align the screw holes,
then securely tighten. You can identify if you have the Quick Connect feature by looking at the
switch housing portion of your light kit. Quick Connect has a distinct locking mechanism on top
of the switch housing, as well as a ring that surrounds the middle of the switch housing.
Non-Quick Connect fans do not have either feature. Connect the plugs from the fan and light fixture,
making sure to line up the colored markings on the connectors. Push the connector and extra wire
into the hole at the top of the light fixture. You need to do this to mount the light fixture
to the fan successfully. Lift the light fixture to the bottom of the fan. Align the holes on the
mounting ring on the top of the light fixture with the spaces in the mounting bracket on the
bottom of the fan. Hold the fan body still while you turn the light fixture clockwise to engage
the locking pin. You'll want to listen for the click to know it's secure. Remove the socket rings
in order to install the light glass. After you install the glass, install the light ring back
into the socket. Tighten them by turning them clockwise with the socket ring glass tool that
came in the fan box. Repeat for all three glass shades. Install the included LED bulb into the
socket. Repeat for all three bulbs. Screw two housing assembly screws halfway into the switch
housing mounting plate. It doesn't matter which two holes you choose. Feed the wire connector
through the center hole of the upper switch housing, then wrap the keyhole slots around the
Insert the third screw into place, then tighten all three screws.
Connect the connectors from the upper and lower switch housing, making sure to line up the colored
markings on the connectors. Partially install two of the switch housing screws. Align the notches
in the sides of the lower switch housing with the screws on the upper switch housing. Twist the lower
switch housing clockwise to lock it into place. Install the third switch housing screw and tighten
them. Install the light shades by loosening the thumb screws, lifting the shade to the light
fixture, then tightening all the thumb screws. Repeat for all of the light shades. Install a bulb
into each socket. Connect the appropriate pull chain pendants to each of the short chains coming
from the switch housing. Connect the connectors from the fan and light fixture, making sure to
line up the colored markings on the connectors. Push the connector and extra wire into the hole
at the top of the light fixture. You need to do this to mount the light fixture to the fan
successfully. Lift the light fixture to the bottom of the fan. Align the holes on the mounting ring
on the top of the light fixture with the spaces in the mounting bracket on the bottom of the fan.
Hold the fan body still while you turn the light fixture clockwise to engage the locking pin.
You'll want to listen for the click to know it's secure. Lift the glass globe and attach
it to the light fixture using the three thumb screws, tightening the thumb screws by hand.
Install the included LED bulb into the socket. Partially install two of the switch housing
screws. Connect the connectors from the upper and lower switch housings, making sure to line
up the colored markings on the connectors. Align the notches in the sides of the lower switch
housing with the screws on the upper switch housing. Lift the lower switch housing and
twist it to lock it into place. Install the third switch housing screw and tighten all three switch
housing screws. Thread the fan pull chain through the hole in the light kit.
Install a light bulb into each of the sockets. Press the globe and globe keeper flush against
the metal plate. Thread the light pull chain through the hole in the center of the finial cap
and thread the fan pull chain through the hole in the side of the cap. Thread only the light pull
chain through the hole in the finial. Screw the finial onto the threaded rod. Connect the
appropriate pull chain pendants to each of the short chains coming from the switch housing.
Locate and remove the two screws on the light kit that attach the light kit to the lower switch
housing. This allows it to be removed from the lower switch housing. Disconnect the blue and
white wires in the light kit and lower switch housing. Install the dummy terminal provided
with the light cap to the end of each wire in the lower switch housing. Using a phillips head
screwdriver, install the switch housing cap using the two switch housing screws you removed earlier.
Connect the connectors from the upper and lower switch housings, making sure to line up the colored
markings on the connectors. Lift the switch housing to the bottom of the fan. Align the holes on the
mounting ring on the top of the switch housing with the spaces in the mounting bracket on the
bottom of the fan. Hold the fan body still while you turn the light fixture clockwise to engage the
locking pin. You'll want to listen for the click to know it's secure. Uninstall any pull chains,
cap, and finial, globe keepers, glass, and light bulbs as needed. Using a phillips head screwdriver,
remove the two screws from the bottom of the light cap. Disconnect the wires from the light
kit. Install a dummy terminal or wire nut to the end of each wire and tuck any remaining wires into
the switch housing. Install the cap with the two provided screws using a phillips head screwdriver.
Reinstall any pull chains as needed. Once you finish installing the multi-arm light,
globe light, or no light cap, you can turn the power back on.
Install the included battery into the back of your handheld remote.
Press the fan button to turn the fan on and off. Use the arrow buttons to change the fan speed.
Press and hold the fan button to change the ceiling fan direction.
Press the light button to turn the fan light on and off.
Enable light dimming and dimmable fan lights by pressing and holding the arrow buttons.
