Lecture 59: Euler’s equations of motion: examples

IIT Roorkee July 201
61 followers
7 Video Views·Oct 3, 2024
In this lecture, we discuss a few examples related to Euler's equations of motion.
Hello everyone.
Welcome to the lecture again.
In the last lecture, we looked at the rotating frame of reference and the Euler equation
of motion.
Today, we are going to look at couple of examples of the Euler equation of motion.
But before that, let us revisit the equation.
So, let's say we have a rigid body and on this rigid body, we can either have a fixed
point or let's say the center of mass Z and X, Y and Z are the fixed frame.
So that means they do not rotate.
So we have X, Y and Z.
These are the fixed frame and we have a small x, y, z axis.
So these frames are the rotating frame with let's say an angular velocity capital omega.
So it is rotating about some axis and let's say the angular velocity is omega.
So small x, y and z, these are rotating frame with angular velocity omega.
Now if the small x, y, z axis are the body frame, so that means that small x, y, z axis,
they are attached to the body.
In that case, if the body rotates, then the small x, y, z axis also rotate.
So in that case, small omega becomes the angular velocity of the rigid body.
And if our x, y, z axis, they are the principal axis of inertia, in that case, we have the
Euler equation of motion which is summation m x equal to I x x omega x dot minus I y y
minus I z z omega y omega z summation m y equal to I y y omega y dot minus I z z minus
I x x omega z omega x and summation m z equal to I z z omega z dot minus I x x minus I y
y omega x omega y.
Here this I x x, I y y and I z z are the moment of inertia about the x, y and z axis respectively
and omega x, omega y and omega z are the component of the angular velocity along the small x,
y and z axis.
Now let us look at an example and the problem statement is following.
A thin uniform plate having a mass of 0.4 kg spins with a constant angular velocity
omega about its diagonal AB.
If the person holding the corner of the plate at B releases his finger, the plate will fall
downwards on its side AC, determine the necessary couple moment m which it applied to the plate
would prevent this from happening.
So in this question we have this uniform plate, this length is 300 mm, this is 150 mm and
we have the x and y axis which are attached to the body and its center is the center of
mass G.
So, this is y axis and the x axis and this plate is rotating with an angular velocity
omega, this point is B and this point is B. So, because the x and y axis they are attached
to the body and x and y axis are also the principle inertia axis of this body.
Therefore, we can use the Euler equation of motion and the Euler equation of motion is
summation m x equal to I x x omega x dot minus I y y minus I z z omega y omega z summation
m y equal to I y y omega y dot minus I z z minus I x x omega z omega x and summation
m z equal to I z z omega z dot minus I x x minus I y y omega x omega y.
Let us call it equation number 1. Now, the first thing that we have to find out is the
moment of inertia about the x y and z axis, so that we get these values. So, I x x the
moment of inertia about the x axis that will be m a square divided by 12, where a is the
length of this rectangle, so that will be m by 12 and the length is 300 mm, so 0.3 square,
so that will be 0.4 divide by 12 because mass is 0.4 multiplied by 0.3 square and that comes
out to be 3 into 10 to the power minus 3 kg meter square.
Now, the moment of inertia about the y axis will be m by 12 into the length which is 0.15
square and m is 0.4. So, therefore, this comes out to be 0.75 into 10 to the power minus
3 kg meter square and the moment of inertia about the z axis can be find out by the perpendicular
axis theorem. So, I z z will be m by 12 I x x plus I y y, so 0.3 square plus 0.15 square
and that comes out to be 3.75 into 10 to the power minus 3 kg meter square. So, we have
the I x x, I y y and I z z. Now, let us find out the values of omegas,
now let us say this angle is theta, in that case tan theta will be 75 mm divide by 150
mm, so this gives you theta equal to 26.57 degree. And from here because we have omega
we can find out its component along the x y and z direction. So, therefore, omega x
becomes omega sin 26.57 degree, omega y becomes omega cos 26.57 degree and omega z is 0 and
you can see that omega x, omega y and omega z they are fixed values. So, therefore, omega
x dot is 0, omega y dot is 0 and omega z dot is also 0.
So, now let us put these values in equation number 1, so we have omega x dot, omega y
dot and omega z dot they are equal to 0. So, therefore, the first term will not contribute
and omega z is also 0, so omega z and omega z is 0. Therefore, summation m x is equal
to 0 or m x is equal to 0, similarly m y is also 0 and m z will be 0 minus let us look
at I x x, I x x is 3 into 10 to the power minus 3 minus I y y, I y y is 0.75 into 10
to the power minus 3 into omega x omega y. So, omega x is this and omega y is this, so
let us put it here omega sin 26.57 degree into omega cos 26.57 degree and this comes
out to be minus 0.9 into 10 to the power minus 3 omega square Newton meter.
So, this much amount of moment needs to be applied to prevent this plate from falling
down. Now, let us look at another question statement and it is following, the plate form
acceleration omega 2 dot. At the same time an internal motor spins the uniform disc B
about its axle which is rigidly mounted to the plate form at an angular velocity omega
to the disc B by its axle. So, we have to find the couple that is applied to the disc
B, again you can see here that small x y z axis, they are embedded in disc B and small
x y z axis are also the principle inertia axis. Therefore, we can use the Euler equation
of motion.
So, the Euler equation of motion is summation m x equal to I x x omega x dot minus I y y
minus I z z omega y omega z summation m y equal to I y y omega y dot minus I z z minus
I x x omega z omega x and summation m z equal to I z z omega z dot minus I x x minus I y
omega x omega y. And we can use this equation as I said because small x y z axis, they are
embedded or attached in disc B and small x y z axis are the principle axis. So, again
to apply these equation, we should know what is omega x dot, what is omega y omega z and
so on. So, let us find out these quantities. So, from the figure, you can see that the
disc A is rotating horizontally with an angular velocity omega 2 and the disc B is rotating
with an angular velocity omega 1. So, from the geometry, I can write down the
angular velocity omega which is a vector quantity as omega 1 i cap plus omega 2 lambda
cap, where this lambda cap is the unit vector which is perpendicular to the platform. So,
it is given here that this one is lambda. So, let us take the unit vector along this
direction. So, from here, you can see that we already have how much is omega x omega
y and omega z. So, omega x is omega 1, omega y is 0 and omega z is omega 2. Now, we have
to find out how much is omega x dot omega y dot and omega z dot. So, from this equation,
let us write down omega dot. So, omega dot will be let us differentiate this equation.
So, we have omega 1 dot i plus omega 1 i dot plus omega 2 dot lambda plus omega 2 lambda
dot. Let me write here again that this lambda cap is unit vector which is perpendicular
to the platform. Now, here lambda dot is not going to change. It is always along the z
direction. So, lambda dot, first of all lambda is in the direction of k and lambda dot is
0. Now, let us look at i dot. So, i dot will be, so you can use the relation v equal to
omega cross r. Here, r is the unit vector which is i. So, therefore, i dot will be omega
cross i. Now, we already have omega. Omega is omega 1 i plus omega 2 k and cross product
with i. So, this will give you omega 2 j. Therefore, my omega dot will be omega 1 dot
i plus omega 1 omega 2 j plus omega 2 dot k. Therefore, omega x dot will be omega 1
dot. Omega y dot will be omega 1 omega 2 and omega z dot will be omega 2 dot. Also, note
that here the x y and z axis, they are the principal axis. Because of the symmetry, the
moment of inertia of this disc B about the y axis and the z axis will be the same. So,
i y y and i z z will also be equal. Let us put this in equation number 1.
So, we have summation m x equal to omega x dot is omega 1 dot and i x x is i x x omega
1 dot minus. Now, omega y is 0. So, this will be 0 and therefore, this is equal to 0. So,
i x omega 1 dot and summation m y will be i y y omega y dot. Omega y dot is omega 1
omega 2 minus i z z. I z z is say i z z minus i x x into omega z omega x plus i y y omega
x. So, omega z is omega 2 and omega x is omega 1. Because of the fact that i y y and i z
z are equal, therefore, this term will get cancelled with this term and we have i x x
omega 1 omega 2. Now, let us look at the moment about the z axis. So, it will be i z z omega
z dot. Omega z dot is omega 2 dot minus we have omega x omega y, but then omega y is
0. So, therefore, it will be 0. So, that is equal to i z z omega 2 dot. So, these are
the component of the couple that are applied to the disc B by the axis. With this, let
me stop here. See you in the next class. Thank you.
