I FIXED MY LAND ROVER TO PROVE IT S BETTER THAN A TOYOTA IN EVERY WAY

RetroCarz
284 followers
On today's episode of Watch Jericho we are back in the shop with my 2002
Land Rover Discovery 2 Kalahari edition and today we're going to make it drive
again because it stranded me at the worst possible
time. What is going on guys I am Watch Jericho
and today like I said we are back in the shop
with the Land Rover and today I found parts so we are going to put this thing
back together and take it for a drive hopefully by the end of the day.
So in the last video of course we found out that the tensioner
bearing here left the chat in multiple pieces it machined itself
just into nothing right it machined itself into metal dust
and this is what was left of the actual tensioner.
People were saying just put a pulley on that and run it but I don't think so.
We are going to get a brand new tensioner and a new accessory belt
because uh this one's not cutting it literally I
I cut it in half. All right guys here's the Land Rover all taken apart it's time
to clear all this junk out of here and I'm going to make a
parts runs today because I was able to get all the parts
locally so like I showed you guys yesterday the Land Rover is all taken
apart we had to pull all the shielding off over the radiator
we were finally able to get in here to the accessory drive it looks like I do
need to take this guy off because I need to get around the AC
compressor and of course we need to start by
installing the new tensioner so it goes right in that hole right there
and has a little alignment dowel so it's pretty easy
let's go buy some parts and when we get back we can start putting this all
together all right guys O'Reilly's did have some of the Land Rover parts so we
are here to pick them up right now it's not the
tensioner we had to order that but let's do this what's going on well
that's all we needed I see you had to go uh I mean it's it's up in the air
gotta fish it out of the rafters yes sir
gotta get the fishing pole out yep well sweet dude
that's all I needed there we go thank you absolutely I appreciate you brother
yep you too take care have a good one and you have a great day
all right guys let's go put this thing back together
we are back with a pile of parts this is our tensioner which is
pretty funny look at that forbidden in passenger aircraft
and then we have our v-bell here which is the k070922
now I just cross-referenced that from the belt that was on here but when you
look it up it does say that it fits the 99-04 Land Rover so I think that's
correct and I think this tensioner is correct as
well sure it looks right all right we'll just
let that fall down I was worried about that alignment pen
but it looks like everything is correct so
with that said fully matches up let's get to mounting our new tensioner
and then we'll move on to taking off the the ac belt cover here
because I do want to be able to route the belt correctly obviously
and also I need to look up the belt routing because I have no idea where it
is and as you guys know they don't print them anymore they used
to always be under the hood but it looks like it's relatively simple
it's got to be like you know up here there must be a pulley
over here oh there's not interesting this covers up
nothing I wonder if that's for like a second alternator or something
kind of strange uh well that changes my belt routing
but you know it must go under that over this
and then maybe down to the water pump back up to the alternator and the rest
of it should be should be self-explanatory but we'll
figure it out maybe I'll throw it on screen
but let me grab a tin pull this cover off of here and
go ahead and throw this back in which should be relatively
easy let's see if we can snake it in there
actually looks like it might be easy wow putting it back
is much easier than taking it out was all right let me get the bolt in there
and tighten it up well getting the tensioner in place was
super easy obviously just give it a little wiggle
get that bolt in there and it's finished right
access is a little tight I ran it in with the electric ratchet a little ways
and finished it up with a wrench because once you get close the ratchet doesn't
want to clear the pulley there it was easier before
because the pulley was falling off the tensioner so
now a little bit less easy so next up is the belt here
and to do that you'll want this panel off and you're gonna have to wiggle it
around the fan here so you're gonna have to snake it down
through here and go all the way around the entire fan assembly
and then slide back a stage and we'll figure out the routing
so i'm going to look up the routing right now as you can see i did pull that
cover off the ac compressor there so that's it's easy to get it off but
mine was broken so i did already repair that with a little jb weld right there
so all the way over it i use the clear stuff and put it on
pretty thick so i'm hoping that builds like
enough of a layer around it that that just sets up and stays together forever
right uh who knows vibration heat all that fun stuff
don't know if it's gonna hold up like a brand new piece of plastic wood but
that's kind of old brittle plastic just like the back bumper is on this
thing uh it's like an old thermal plastic you guys know the brittle black
stuff that's what it is so uh it's not the best
plastic i just hope my repair holds as we put this back together
and it looks a bit prettier it was broken before but
uh now that it's off we'll be able to get in here and put the belt on so let's
get to it all right guys we figured it out here's the belt routing diagram
if you have the active cornering which this one doesn't because this is
supposed to be the special off-road version
one they took away like the streetness of it when they lifted it and put the
big tires on it from the factory here so if you have the more streetable more
loaded one you have uh an active cornering hydraulic
pump hiding right here and i mean it looks like it has a little
dowel and everything for that pump to mount to but
this one does not have that so we get to use the much much simpler
belt routing diagram here which is just well i'm just going to jump in here and
do it but basically string the belt under the water pump and then
flinging around all this stuff and tighten it up so give me a second here
this isn't something that we can easily video we're just going to slide in here
and do it well it's been about 30 minutes since we started this was one of
my hardest fought serpentine belt battles of all time
it is nearly impossible to do without taking the fan off and
yes don't worry i read the comments and i saw that a couple people were saying
yes i'm screaming at the screen you know take off the fan these fans do
not come off and it's a mistake to take them off
usually if you take them off you're not going to get them back on
unless you do that cool trick that that one guy did that made him almost lose
his fingers where you like start the car and then float it right at the end of
the threads and then once it starts you just kind of let go and the engine
spins it up to speed instantly and then snaps it on that's like the only way to
put this back on there's no clearance anywhere around this thing because i'm
sure land rover has a special tool that removes its fan it's like some
crazy extended fan clutch tool and i of course have the normal lyle one that
every mechanic on earth has that has you know all the ones in it that
once in a while once in a great while i think this has ever worked
twice out of maybe 10 times we've dug it out and tried it
it never works and if you don't have the special one for the land rover that must
be like a foot long you can't get enough clearance for the
air hammer to even hit right because it's like everywhere you go it's up
against something and you can't counter hold the pulley
so you know i read the comments and i i think the comments were wrong
okay cool i'm a little concerned about clearance there but it looks like
everything is right and the belt routing is sure
right so we're ready to start this thing up now and see what happens
i was able to get it on i'm telling you it took a long time to get the belt
sorted out but i think we're good to go now so let's
start it up and then we can put all the plastics back on and refill
the coolant if i was wrong anywhere it's going to
throw the belt again so hopefully i wasn't wrong
all right here we go
but on the dash oh sorry it was out of focus the whole time but the dash is
awesome i love that there's a lot of air
all right guys let's put all this back together okay refilled the coolant
bled it again and it looks like i need to add a little
bit more to the reservoir but hey the hoses are nice and full it is time for
us to put all the plastics back on here so to
start with we're gonna put this guy kind of in
its place work it down in here and then we'll
move on to that top bolt which was the one that was broken i want to be gentle
with that tab up there that one's about where it needs to go
and this one goes oh it has a standoff okay so the bolt has
a standoff in it just like that and you slide that in
there and then run the bolt through it so that's what holds that up and off of
the belt there so let me reassemble all this and we'll
tighten it up and move on boom the land rover is all buttoned up
again oil check cooling refill i mean she is
happy the oil in this thing looks brand new so i think we are ready to rock
and of course all the covers shrouds are back on here so
let's take it out it's actually out of gas too so let's go fill it up
and take it for a little drive here so we can see
just how ready to rock the land rover is hopefully it's ready to take on a toyota
that's what we're going for here i posted my land rover will always be the
toyota post on the old internet and the toyota guys were mad as you guys
would expect right uh they they take it very personally so
they want to have a toyota land rover off now so we'll see we might actually
go crawling and see who wins because i think this thing is
insanely capable i just need it to not break
oh the hood prop just fell off when it shut
i gotta open it back up and what i tell you guys we're about to take on these
monster snow drifts oh the land rover does it with ease
all right abs actually traction turned on it's pretty funny this old school
traction and this does absolutely nothing you always hear it
start running and it just makes this little
noise and what else is there to do i mean it's like full-time four-wheel
drive with solid axles what is traction
control supposed to do i'm sure it's supposed to individually
break the wheels but it can't do too much for you at that
point you're you made your bed lying that's how traction works in this old
land rover oh oh more snow oh we hit it going right
through it anyway as you can see most of the snow
melted off today was 58 degrees so it was an
awesome day actually the perfect day to get rid of
the 10 inches of snow we had sent around here you can see it's still piled up
everywhere but i can't quite bomb over all these curbs
it would definitely wipe out their grass and i'm not trying to be that guy
but this thing drives so nicely so nicely it's like it's brand new
kind of unbelievable no lights on the dash it's just a great
old off-road truck apparently when kansas sprays all the roads down their
anti-ice solution is prune brine or something like that
so it's like fruit juice all over the roads and apparently that works
but all i can tell you guys is the land rover is back on the road
and i let a little pressure out of the tires and it's way quieter right it
sounds even better super solid now um i was running 60 psi
all the way around because they do recommend running truck pressures on
these good years these are the old kevlar good years but
i dropped it down to 55 all the way around and it seems
much quieter and nicer so there you go we're ready to go mall crawling again
and possibly take on a sahara or a safari or the tundra
one of these days all right guys there you have it the land rover is back in
action ready for the next winter storm i don't know if i'm going to actually
try my luck but it would be funny if we took it back out in the snow again
and it might be a lot better at it all i know is the next thing this gets
is a good detail because it is absolutely
destroyed we probably won't make a video on that though because well as you guys
know there's only so much saving you can do before this thing needs to repaint
that is it for today guys thank you so much for watching don't forget to head
on over to shopwatchjr.com for cool shirts
just like this and please like share subscribe do whatever you want to do and
i will talk to you next time and you know what that's what it
needed it needed a little oil check and a coolant flush and a new accessory belt
so now she's back in action and better than
ever i absolutely love this thing so i'll keep
driving it and we'll see if it breaks again it's a content machine like you
guys keep saying and i know the disco 2 community is
awesome before i even have questions about stuff on this
someone's always in the comments saying like you should do these things first
and believe me it's not the accessory belt the serpentine belt
but it's actual disco 2 specific things and it's really cool they're always on
top of anything that could go wrong with this
so that's the update on the land rover i'm
sure there will be more to come
