Nissan NV300 13 Dealership Repairs But Fault Returns Same Day 253F29 Oil Dilution 200291 DPF 200292

AutoTuned TV
1 follower
5 Video Views·Dec 8, 2023
Particulate Filter & Oil Dilution Fault.
Oil Dilution Fault reappears same day after Oil change and reset.
same van as..
Vauxhall Vivaro
Nissan Primastar
Renault Trafic
Fiat Talento
DPF cleaning done to verify the Diesel Particulate Filter is damaged.
for repair bookings email [email protected]
[Music]
hello it's Jimmy here the Roes I have
here to look at a Nissan NV 100 which is
basically a Renault traffic or a vool
Vero so I've just finished one here
another one which is the fox ol varl
doing a DPF clean now this one has or
needs a similar sort of repair but it's
got a different side of a story to it
this one so I just thought I'd make the
video
and tell you what's been going on so
it's been back to Nissan more than a
dozen times and it's been to two
independent gares and it's had new fuel
injectors new EGR valve new glow plugs
new adloo injector and various other
bits and pieces turbo pressure hose and
pipe and a turbo pressure sensor and
within a few days after it's all been
done it's had uh five or six forc
regenerations but each time it leaves
the garage after a couple of days the
DPF block sign comes back on and he's
just come down to me
to get an answer on why it's happening
why does the DF keep getting blocked so
we're going to have a look at it and uh
find out okay so it's got engine failure
Hazard message on and a spanner on the
dashboard there it's got round about 180
MB of pressure at revs and we have I did
try and clear some of the codes but they
just come straight back so
20292 particle filter clogged and a 2002
91 particle filter outside tolerances
also an engine oil dilution comes up and
he said the engine oil has been changed
I'm think he said 13 times uh in the in
the last 12 months uh now the van was
under warranty it's been going to Nissan
uh it's been there more than a dozen
times like I said and each time they
just keep saying well we fix the problem
but then a couple of days later the
problem comes back and they send it
don't know why the particle filter keeps
getting clogged so now unfortunately for
me what I'm going to have to do for this
is we've got almost 200 mli of pressure
on the DPF so what I'm going to have to
do is I'm going to have to attempt to
clean this DPF to find out if it's if
it's cleanable because what we have here
is just a particle filter clogged and
engine oil dilution which is already
been done the engine oil has been
changed and the particle filter was
regenerated forced forced regenerators
um and a couple of days later it comes
back now I've just cleared these took it
for a drive and they've come straight
back
again
so what I'm going to need to do is try
and clean the DPF and hopefully if we
see that DPF pressure come down from 180
to 200 it was at 210 but it's come down
to 180 so if it comes down from around
the 200 meric down to what we wanted
sitting at idle is round about five or
six Ms of pressure if we get it down
down there we know all is going to be
good if it doesn't come down there the
reason these faults are going to be
coming back is because the DPF is
damaged or
melted okay if we have a look down here
we can see it's had a few shiny Parts
fitted to it so what we're going to do
is I'm going to remove one of these
sensor holes here and we'll get some
cleaning fluid injected in and then see
how it goes now before I finish this
video or started what I'm going to say
is I've I've already got a feeling that
I think the DPF is damaged but just to
confirm it we're going to have to put
some cleaner in there and what I'm doing
I'm not going to guarantee that this
cleaner is going to work but we need to
find out so there's only one way to do
that which is attempt to clean
it okay we've put the DPF cleaner pipe
in through the oxygen sensor I've
removed that with a 22 M spinner uh
we're now already just putting the
cleaning fluid in so I've got this kit
here it's a pressurize bottle with the
fluid from launch
UK getting that squeezed
in
okay that's all been connected back up
now what I've just been told by the
customer as well is they've put a new
catalytic converter on it and the ad
blue injector down down below so this is
the DPF and then further down you've got
the Cal
converter okay we're back in the van
we'll hold the ribs back up it's really
difficult to get these to stay at around
about 3,000 RPM but you see it just
starts creeping
up hold the pressure
there hold it
there we got around about 220 let's put
a put a graph on
this okay so that has come down yet um
should have probably showed at the start
of the video but we had like 850 mli of
pressure there but what we want to see
here like I said now on revs we want to
see this at 50 you know 40 to 60
Ms 200 is still not good enough but
we'll hold the revs here now for a
couple of
minutes see where we're sitting where
are we sitting at idle let's let the
idle
down oh we've got 50 but obviously
that's still high want to see that round
about 4 to 6 M of
pressure
so I'll continue to hold these revs for
a couple of minutes and then we'll get
back okay so we seem to have evened out
there around about 158 mbars let's Let
It idle down see where we're
at still
36 so that's what I was expecting to see
with this is that the DPF pressure is
going to be sitting a little bit too
high so it's constantly going to be
trying to regenerate and then the van
will just give up after a certain length
um what I'm going to do now is I'm going
to reset the DPF adaptions take the
vehicle on a test drive see if it's
going to do its own regen or see if it's
capable of doing its own region
and then we will know for sure after
that right adaptiv after replace into
EPF press
that turn off that
radio okay come is in
progress okay now that's all done we uh
can clear the faults
yes completed just read them make sure
that they have cleared
okay now I'm just going to reset the oil
change
interval I know I haven't changed the
oil but it's been done 12 times or 13
times
apparently just reset that just so I
know it's been reset okay now we've got
these two items to look at during the
test drive the particle filter pressure
and the temperature Upstream of the
particle filter so that should reach 6 °
if the Regeneration process is working
and this should come down to sort of
four to six mbar of pressure at idle uh
if it doesn't do that then we know we
have a problem with the
DPF okay we can see the DPF there is
coming up to
600° so I know the regen process is
working
now okay so what we've got is around
about 90 M of pressure now now after
clean's
done at
idle we've still got
20 so
unfortunately even though it's it's it's
kind of close 20 M of pressure is too
high it needs to be under 10 maximum
really you'd like to see it as 8 m of
pressure but 21 mbar of pressure is no
good and unfortunately that's why he is
going to get
again maybe within a few days or so he's
going to get the DPF issue comeb back
it's going to need a replacement DPF to
fix
this so that's it it's a Nissan
NV is it NV 200 or 300 this one
whichever anyway but uh that's it it's
going to need a new DPF unfortunately uh
I don't know why he wasn't told that
before but now he knows see you in the
next
[Music]
video
oh
