Ford Transit 2.2 P0299 Turbo UnderBoost

AutoTuned TV
1 follower
Jul 19, 2024
Boost pressure leaking from fuel injector seals on diesel tdi transit van.
fault codes triggered were..
P0299 turbo underboost
P00BD:00-26 Mass Air Flow Circuit Range/Performance Air Flow Too High
[Music]
hello again Jimmy her Roy Mobile
Mechanic I have here for transic custom
so he's been having issues with this for
a few months again same reason um I know
people some people have had comments in
the past saying every every sort of
vehicle he has he claims that someone
has tried to fix it that's the only
reason people are driving 3 hours to
come to me when he could easily get a Lo
garage the only reason he's drove to me
today is because he's tried three or
four of his local garages and they
couldn't give them a resolution on the
problem so they couldn't fix the fault
or they couldn't find it now I wasn't
really going to make a video on it but I
just thought decided at the last minute
all right you know what I'll make a
video on it because you know it's
another one again we need to raise
awareness on what some of these common
issues are and why we're seeing them so
if I connect up this smoke
machine turn it on
and we'll just switch it on so we got
green and we connect this up here at the
inlet of the car or the van because what
this got is it's got an intermittent
issue it doesn't happen on every Journey
but it will give turbo under boost
p299 it's had all sorts of stuff done as
you can see in there it's had new
actuator put on it
um I'm not sure if that's even a whole
new turbo is it um but yeah it's had
loads of work done five or six occasions
they even changed the fuel pump I don't
know what that was about but he said
it's was going in Lim mode and they said
all right let's try changing the fuel
pump but obviously it's a it's a turbo
boost problem now the problem is is it
doesn't always give a fall coat and the
customer's got his own scan tool uh and
he's been clearing theault but yeah I've
done one of these before so if you have
a look here you can see the exhaust
gases or combustion gases are
um are leaking out there at a very high
rate
so not just slowly this one here got a
bit of a dribble from it as well as that
one we've got a massive leak there on
number
four now like I said the PCM here hasn't
got a fault at the moment because the
customer has been clearing his fault to
um be able to drive the van but what
some of the symptoms are with this is
what the customer saying to me is the
van would go in limp mode but if you
switch the engine off restart it and
your power is back again it'd be fine
but you would have the engine management
light on but the power would return with
an ignition off and on cycle okay so we
disconnect the smoke machine now to fix
this what I'm first going to have to do
is open the fuel rails here 17 mil
spanner get these
open that's actually turning the the
smaller bolt on here so we'll have to
come back to that in a
minute we'll get this one off
sorry just adjust the camera down there
so you can see what I'm doing so yeah
we've got that one loose and then we're
just going to do the same on all four
injectors here so you just use a little
pick tool get in behind here get these
little spring clips out okay so now
we've just popped out these injector
leak offs so you use a little trim tool
here like that push them
out so you can see all four of these are
now out they're all attached together
now we can just get the plugs off for
each injector
here okay now we've got all of the plugs
out we have already loosened these bolts
here 8 mm bolts just get those out and
these injectors they're not usually too
too tight you can see they're hand tight
didn't even use an in need need to use a
tool on that one let's give it a wiggle
sort of left and right there you go it's
out going to need to clean these
up okay so you can see see there we
haven't got the um seal so the seal
hasn't come out so it's going to be down
there you can see why these cause a
boost leak it's because obviously the
rubber gaskets on The Rocker cover here
they leak and then you lose your lose
your pressure out of
there cuz I use this special tool to get
the injector sealed
out that just goes down in there you can
screw it on on and then pull them
out just clean out the injector
SE okay now we can see that's a bit
cleaner so we're just using a little B
scope here just to make make sure that
the port is is
clean so I just used the same f tool
again get it under there we should be
able to just pry that old rubber SE seal
up okay so we just used a little wire
brush wheel to sort of clean break up
the carbonet on them now we can give
them a spray down get these cleaned
up so I just use a little dab of Grease
there and that'll
stick the new injector washer on place
so it's not going to fall out when
you're trying to put it in so this is
the K I'm using here we got set of uh
the rubber gaskets there seils and then
you got the copper one that goes down
the bottom of the injector so you can
see there now we've just basically
pushed all of those back on in reverse
the same way that we've done it as we
took them out so now we're just on to
number one and two here so we' got these
out and this one is in hell of a state
here so going to get this cleaned
up going have some wire brok in
see all of the stuff well that's no
sorry that's some of the metal but
that's some of the pieces of carbon
there that have been flying
off okay that's the four injectors
in put the smoke detector back up and
run it
[Music]
okay so you can see how much pressure
that was hauling and we haven't got any
more leaks around the
injectors okay now let all back together
okay back inside the van we just started
up make sure that it's all running
correctly it's not
misfiring we've not got any blowback
from the
injectors okay so just about finished on
that
one so that is it I'll see you on
another video
[Music]
