Peugeot Partner U029D Fault In DeNox Communication P2200 Nox Sensor Not Communicating

AutoTuned TV
1 follower
Mar 8, 2024
Peugeot adblue fault with the nox sensor
for repair bookings email [email protected]
www.orileysautos.com
[Music]
hello it's Jimmy here the R I have here
a perso partner van or citran Blingo
basically the same it's got an issue
with I believe to be no sensor so he's
had a a scan tool on it sent me a
picture of a code which I believe to be
the nox sensor Let's uh get inside and
have a look okay so inside the van we
don't currently have a on there but
looks of it just yet let's give it a
minute sometimes he'll get fault come up
here but he said it is intermittent he
can clear the fault and it might lastday
and then it'll come back on again so I
don't know if he's already cleared it
looks like he has cuz it's not coming
up so if I use the launch UK Euro Tab 3
we'll do an intelligence scan and it'll
find the vehicle for me and then we can
just do a quick code read and see what F
codes we
have okay so now we're in on the vehicle
we'll do highs speeed
[Music]
scan see what Falls that we have
here so like I said customer has already
sent me a picture of a fall code that
he's been deleting but it consistently
comes
back just waiting for it to scan through
the rest of these
modules
oil gauge fault elimination of
tur and then we've got
u029d fault communication with the doox
system no
communication
p2200 nox sensor component detected
communication on the emission control
Network uh let's go in
here and let's have a look at data
stream see what information I can't
remember don't really do a lot of these
noock sensors anymore just because
they're really difficult for me to get a
hold of them and I don't usually book
them in because of that
[Music]
um see what we have here quantity of
area temperature of the
doo
pressure
D system
to noock content Downstream
Upstream just see what else we have
here anything to do with the noock
sensor could be the noock sensor itself
or
uh anything related
basically let's just have a look at
those
two
right so we're not getting much of from
that because this is these are all
just standard readings because it's it's
not really um even activated Doo system
one Doo system 2 that's about it we'll
just go underneath we'll check the
voltages are at the pins for the no sens
sensor itself so where the plug comes
into these pins here we're going to
check that we've got power running to
the noock sensor and if we have got
power then it's going to point to a
faulty n sensor so we'll just replace
that if we haven't got power
unfortunately it gets a little bit more
complicated have we got a wire an issue
or ECU problem first thing I'll do
is spray this
up some penetrating fluid that's the one
from
launcher just going to let that sit for
a few minutes then if we follow this
cable back over here we have the unit
here that we're going to get
removed get these bolts undone how many
of we got I think we should have two or
is that just a uh yeah that's just a
clip so got one bolt get this
down the other side should just pull
out Okay so we've got this little
plastic casing off and we have this here
we're going to try and test the wire
into it all right so I can see there we
have 12 volts power supply into it and I
can also see we're getting signal there
to it as well and the big reveal is can
we open the center or is it going to
tread
[Music]
out so it looks like it's coming so far
right so we've got that
out um I think some of that penetrating
flu got in there you can see
there that is the tool that we used for
it uh 22 mil Coss foot spinner a nice
big heavy duty one now this new sensor
it's got some anti-seize Grace on it
already so we'll get this fited
in okay now we've got the new sensor all
bolted in we just fit it along here into
these little areas back in the plastic
casing and then we can just plug it back
in and then you got your little plastic
tab there just make sure it's
locked
okay now the sensor has been fitted we
come back in here we're going to look at
special functions replacement parts
emissions
control and have we got the noock sensor
there it
is switch off the ignition and wait for
30 seconds what I usually like to do
before I do this is open the door close
it it just makes the screen go off and
you're going to make sure everything's
going to shut down and I give it about 5
or 10 seconds before I actually press
this
because sometimes the 30 seconds is not
enough and shortly afterwards this light
interior light should go
off okay so that is now reinitialized
the noock sensor now we can go back and
clear theault
memory and we need to read the codes
first it says so read and then we can
clear so now we're going to try and come
back and have a look at some of these
live data what we'll do is come back
from this
one and go to doox
one operating status the bleed status
and the pressure of
the uh ad Blue System we want to wait
until that activates and see if the
pressure builds
up just going to hold the revs to get
the system warmed up once it's reached
temperature it should then reach about 5
and 1/ half bar on here so there we go
pressurization phase has started and
we're up to six six bar now that'll
slowly come down to about 5 and a half
bar there we are if we come back
to DX system 2 and we look at these
again see if anything's changed there
yet I think the car has got to be
driving for these to actually give you a
correct reading but the heating is not
activated
yet
let's take the vehicle on a test
drive okay test drive done now this is
fluctuating between sort of 16 to 50
ppms and if we hold the revs
up do like a 3,000
RPM it's around
120 I do need a little bit more
[Music]
um experience with these ad blue systems
because you know I don't really see a
lot um because like I said I don't
really get too much involved with adblue
because I do find them a bit of a pain
uh getting a hold of part so when people
come for adblue FSE you usually need a
knock sensor that can take sometimes 3
to six weeks to get a hold of or an ad
blue tank and there not something that
you can sort of repair there and then
now that we give it a REV let it idle
and it's down around sort of 10 ppms now
that will go back up again I think but
uh yeah I do need a little bit more
experience on looking at a few of
readings on what is a good a good
reading and what's a bad one but as far
as I'm aware anything under
50 uh at idle is
good but that doesn't mean that it's um
this is not testing the actual knock
Senter itself this is just reading the
effectiveness of the Catalyst
now and we're back here you can go in
read
defaults just make sure that they're
gone
and what we will do is we'll clear the
BSI FS as
well just a little clear from
there that doesn't work that didn't work
did it let's have a look what's going
on okay that's done so we're left with
two Fs in there about the
headlight and we're all done th I'm all
done on this one and I'll see you on the
next
[Music]
video
