Ford Focus ST-D P253F:68-28 P244C:00-68 Oil Deteriorated & Exhaust Temperature Too Low Regeneration

AutoTuned TV
1 follower
2 Video Views·Nov 3, 2023
Ford Focus ST Diesel with blocked diesel particulate filter fuel vapouriser causing repeated DPF issues.
for repair bookings email: [email protected]
[Music]
hello Sim here got here to look at a
Focus ST diesel okay so I'm inside the
vehicle now there doesn't seem to be any
lights on but uh what he's saying is
happening is the vehicle is trying to
regen
every hour at least basically uh it'll
do a regen and then 10 minutes later uh
it'll do another
regen and then so every Journey he does
sorry not an hour yeah 10 minutes he
said every 10 minutes or so you'll hear
it doing a regen and the miles per
gallon has dropped considerably he says
um so he's getting around about 320 M to
a tank where he says he used to be able
to get around about 500
so he's had it at a garage five or six
times uh he's had multiple oil changes
uh DPF
regen Lambda sensors replaced and DPF
pressure sensors have been
replaced set up a diagnostic
scan manual
gearbox okay R so we're just going to
scan the
vehicle not worried about those faults
oil deteriorated and exhaust temperature
too low for the particle filter
regeneration so
uh it's pretty self-explanatory code
really I'm not sure why they've uh not
been able to fix that problem pretty
sure if I press search on that
code you have some of my videos
explaining what that code
means right so not for this particular
car but for transits yep not done one
one of these
before okay so outside here looking at
the engine it's a 2 L
and what I'm going to be looking for on
this is uh part called a vaporizer now
it's going to be down the back somewhere
and this vehicle is quite low to the
ground so I'm not going to be able to
drive it on ramps hopefully I can jack
it up have a look underneath see if I
can locate where the vaporizer is but I
remember doing this engine on a for coua
and it was in a really difficult place
down there managed to get it but this
looks like it may even be more tight
actually I can see the plug there for it
this is the plug but the part itself is
going to be attached to the exhaust
which is down the back of the bulkhead
so just opening these disconnect the air
pipe and try and get this air boox
out see if we can see where this
vaporizer is remove that plastic cover
there what else have we got hold in this
we got a little piece of uh plastic here
attached to that that just fell
off okay so this is the power supply for
the
vaporizer the cable runs around the back
so we might need to get the battery out
as well see if we can see where this
part
is okay I've got the airbox out the
battery out and if we come down
here just over there that's your
vaporizer unit there that's going to be
blocked and we need to get that
removed okay so I've just used some gas
there to R it
up okay so it does not want to come out
it's seized in so what I'm going to do
is connect an air compressor to it going
to put heat on it with the blow torch
and if we get it up to say
800° and use the blow torch sorry the
the airline along with the blow torch
then we should be able to clean it out
so what we'll do is we'll do this and
then we'll test the pressure on it okay
so that seems to have worked now because
we're getting Clear Flow going straight
through the vaporizer we'll get a a
gauge on there just to confirm that
okay I've got a medivac gauge here we
got that connected down there straight
to the
vaporizer absolutely no movement
whatsoever so it's as good as brand new
now really that's the only issue that
you usually get on these of course you
can get a glow plug issue on them but
this is the main issue is the blockage
so before that gauge would have been
reaching up to say 20
psi now we've got a clear
I would have liked to just replace it
but it is not coming out and to remove
it you're going to have to maybe take
off the complete exhaust drop subframe
maybe to take it all out okay so now
I've put it all back together here and
I'm not sure if we went through it at
the start but the live data shows 32
mbar at idle and round about 250 at
3,000 RPM so we're to be safe we're
going to clean the DPF rather than
setting off a
region and we're going to go under the
car to do that okay so what I've done
here is I've removed the tube that goes
into the DPF from the pressure sensor
there we filled it with our DPF cleaning
fluid you can see there Foams up and
expands everywhere into the uh
DPF I'll let that sit for 5
minutes okay so now I'm back in the car
and you can see that this code here
engine exhaust temperature too low for
the particle filter regeneration that's
because that vaporizer is blocked was
blocked and it's not sending fuel into
the DPF to get it heated up the DPF sits
way down the middle of the car here on
these and it needs the vaporizer to
increase the temperature by spraying
fuel in there so now I'm going to get a
few items up on live data differential
pressure have a look at the
soot
and exhaust
temperature this
one okay so now we can we've got all of
these items up we're going to start the
engine up on the vehicle
here let idle for a
minute give it a couple of
revs now we've got the DPF pressure up
live here so we'll hold the revs up at
round about 3,000
RPM try and get it to stay steady there
we
are
see a lot of vapor like that coming from
the
[Music]
exhaust
hold the revs and after a minute or two
there you should see the pressure has
come down to around about 50
m let's let go that and let it idle down
see where our idle pressure is 1 M
bar now if we watch the DPF sit at the
top there you can see that that's coming
down
so now that the pressure is down to a
safe level we're going to go to special
functions power control module reset the
particle filter learn values that's
going to reset set the I'll show you in
just a
sec okay now that's reset we're going to
go to clear the fall
codes if we go back to the Daily stream
again so you can see the top one there
was moving down but one of them will
lock in and that will not reduce without
resetting the um the DPF
values okay so now we've got the vehicle
running again we're sitting back at
around about 1 or 2 m of pressure
okay now we're just taking the vehicle
on a road test for maybe 5 miles or
so so usually these fors after a short
test drive they will trigger off a regen
so we'll see if that
happens so yeah the temperature did
increase there now these numbers should
start coming back down
again okay now back for my test drive
check Thea codes that they're all clear
okay so that's it we're all finished on
the Ford
Focus and see you on the next
[Music]
video
