Lecture 19 - Transceiver Architecture - VI

IIT Roorkee July 201
61 followers
Jan 25, 2024
Concepts Covered: Digital IF Receiver, Super Regenerative Receivers
[Music]
[Music]
uh welcome once again to RF transceiver
design course we are discussing about
trans architecture we left at the poly
uh RC polyphase filter discussion uh one
more thing I want to add in the RC
polyphase filter that we can also make a
cascaded polyphase section and what will
happen that you can make a uh same uh
output again connected to input and we
need to rotate it so here it is a
rotated one so this is a first section
and then there is a rotated section
again the output of one will be given to
uh input to the other and that uh widely
it is mentioned like this this is a
stage one this is a stage two stage
three stage four and what is the
advantage of this in uh simple if we
consider only R1 C1 it is a very limited
bandwidth however we can improve the
bandwidth of the rejection by adding the
cascaded stage but it has also some
disadvantage if there are more variation
in the r and C then there is a
possibility that you have a your image
rejection ratio throughout the band will
not be constant and uh there is a uh
loading means because there are more RC
there is a loading effect is also going
to come so that you need to consider
while designing a multiple stage
polyphase filters uh this uh we'll uh
here we are concluding for the fifas
filter and that are the all the image
reject receiver we have
discussed now there is a one more thing
you can also use uh you can also add the
uh 90° phase shift prior to the doing
after the uh down conversion um at the
input side but we the we generally avoid
this because at the input side if we try
to add the RC the it is possible that
your noise will increase and you can not
get sufficient pH change at very high
frequency but there are certain
application where uh let's say you can
use a quadrature hybrid couplers by
using inductor and capacitors which will
Prov provide you 0 and 90° pH shift at
the RF end then you can Al you can use
this kind of architecture where you
convert the RF signal to 0 and 90 and
then you just use apply sin Omega cos
Omega T and this is a how you can do the
image rejection there is another way
also which is a simplest way if you uh
don't want to uh Implement RC filter
just directly you convert the S and
cosine signal uh in ADC convert to the
digital and then again uh on the digited
domain you add the 90° pH sheet and then
add so this is how so here
also ADC or there is a quadrature ADC
that can be used and the complete down
conversion you will do and the digital
domain so uh where it is uh easy to add
the 90° phe shift in digital domain so
in many
application uh that on digital side also
uh people has a tried to in do in the
literature so these are the two
alternative way we can also add the 90°
phe
shift there is a uh digital I so in some
of the literature it is called as a
digital I where
mostly the Bas Band After the down
conversion I filter enti uh EDC has been
used and then you have a channel
selection which is a reconfigurable so
that can be a software defined so you
can easily do the image rejection and
the band selection but channel selection
so entire band will be uh converted to
the digital and then in digital we will
select the the channel instead of using
a channel select filter however in this
case you required a uh addic with very
high resolution and uh it dynamic range
should be high it require many bits but
but there is a flexibility in terms of
the reconfigurability you can easily
select the channel so it is called a it
is named as a digital if because you are
uh adding the uh Recon figura
reconfigurability at the
basement even uh there are some uh
receiver architecture for mostly for
radar application has been tried where
after the LNA direct ADC has been used
and uh the channel selection and
everything the means even down
conversion is uh also has been done at
the uh digital site so the this is a
special kind of ADC that will also help
uh this will work at very high carrier
frequency and it will uh convert to the
digital data so this is called a digital
if uh
receiver there is another class of
receiver that uh I have added here
because it was a uh in the uh Century
1914 Century uh at Edwin Armstrong has
invented and it is the first uh receiver
architecture that was employed in the
radio and it is called a
regenerative uh super regenerative
receiver architecture the it is very
simple architecture where positive
feedback is used and where your inductor
capacitor is a tuned so this is uh the
paper in which uh Edwin Armstrong has
discussed this architecture this is
referred from that paper and here the
due to positive feedback the moment L
and c will tune to the frequency of
incoming uh signal then you will have
the high output voltage the this is a
basic block diagram so this can be
converted into the block diagram where
there's a amplifier and feedback that is
a tune and at a tuning frequency this
will amplify the signal and and then
there is a detector which will in this
case it is a speaker so uh uh in 21st
century why I'm talking about the super
regenerative receiver because it has
also
application if you are going for the uh
let's say biomedical application or
where your uh RF frequency is in
megahertz there are in certain iot
application also where you don't want to
add too much complexity and you want to
reduce the power consumption in that
case we can use this architecture and uh
in some of the uh biomedical uh
architecture uh many papers are
published on super regenerative receiver
so the this can also be considered as
one of the receiver architecture it is
Advantage is that it is a simple and uh
it can uh easily implemented but the
disadvantage is it is involve positive
feedback so uh you required a very fine
tuning so tuning is very important in
super regenerative receiver
architecture then there's impulse radio
receiver architecture so it is used for
short range uh low power and high speed
application where very uh means a pulse
of the signal has been sent and uh for
short range uh we within a range of 3.1
to 10.6 GHz and what what you you can do
is just uh uh use a mixer and envelope
detector uh to down convert the signal
so it is mostly used where uh in radar
application this kind of impulse radio
receiver where you uh send a pulse and
then try to receive the pulse and find
out the distance
between the object and the receiver so
that that has a specific for specific
application impulse radio receivers are
used and it is a combination of mixer
and correlator the only the disadvantage
of this architecture is you need to have
a very wide band 3.1 ghs to 10.6 G that
means your LNA mixer all the components
should would work for that entire band
and that that will limits the
performance of this uh radio impulse
radio
receiver so let let we summarize we in
last one or two two three classes we
have gone through various receiver
architecture if we summarize the
receiver
architecture then uh these are the basic
summary you can keep in your mind so uh
just now we have considered the super
regenerative receiver architecture the
complexity is low you can also use do
the full integration is possible the
power consumption is also low and same
thing is applied to impulse radio
receiver it is a complexity low full
integration is
possible however no carrier impulse with
wide bandwidth can cause interference
with other system if emitted power is
not limited so we need we need to
consider that our emitted power is a uh
limited uh High sensitivity because of
the resonant feedback there is a
sensitivity is better in super
regenerative however uh in impulse there
is a high bandwidth of this allows the
high data rate so very uh let's say
because the wide and with it as a higher
data rate uh it can provide the high
data rate and you can uh easily also
reconstruct the image me in the mostly
in uh sensing image and sensing this
kind of impulse radio can be used then
super rodine uh we already seen the
complexity is moderate full integration
of cheap image eject and channel select
filter you we need to use so there
are it is a trade off it is it cannot be
have a uh all the cheap complete cheap
Solution on the single chip we have many
components need to use the op chip the
power consumption is a moderate and if
has to be trade off in channel selection
and image action so uh we already seen
that uh we need to consider the high
frequency so that we can all so use
channel selection and image rejection
both there is a d dual super inine
architecture it is very highly complex
we have seen that multiple down
conversion we are trying to do uh it is
a full integration is uh there are OB
components that's why it is not possible
power consumption is very high because
you have multiple components and at
least three or four cheap solution is
there each SE and you need multiple
synthesizer so power consumption is very
high and good image rejection so it has
a advantage that it will provide a very
good image rejection and channel
selection so where your uh mission is
very critical and you need uh uh your
accuracy to be very high at that time
this kind of superrod dine architectures
are used D now direct conversion
receiver it has a very low
complexity and there's a full
integration is
possible the power consumption is low
what are the problem of DC offset we
already have seen uh problem of direct
conversion receiver the that is a DC
offset or the it is a sensitivity to
sensitive to the flicker noise but this
is this architecture is also widely used
because uh it is is very simple and un
cheap the space and size it is taking is
too
low the uh another widely used on chip
architecture is a low if receiver it is
complexity is a low and moderate full
integration is possible power
consumption is low and moderate and
overall there is a good
performance and digital if RF very low
baseband and uh very high R frequency
complexity is very low but for base band
very high because here I told that ADC
required a high dynamic range so when we
are designing the Bas band the
complexity will increase full
integration is possible uh we can also
have a uh high power consumption because
of the multiple uh Bas band modules uh
very flexible archit Ure and can handle
different standards modulation and
frequency so there is a software defined
uh if so that is why we can have a more
flexibility in terms of selection and
all however ADC limits the dynamic range
and which is a major drawback so these
are the all
the receiver architecture here when we
have considered the hrod dine super Hine
and dual super rodine in uh both the
case uh you can also use
so uh either heartly architecture or
viewer architecture all the image
reject architecture are a part of Hine
architecture even a low if you need to
reject the image so that is a uh Hine
architecture and in direct conversion
you have a Omega RF is equal to Omega l
so it is a direct converted to the
basement so this is all about the
receiver architecture that we have seen
and uh this uh entire uh module will
help uh help you to uh Implement any
receiver architecture that uh you want
to perform now we will move to the uh
transmitter architecture so the basic uh
difference
between receiver and architecture so
when when we have considered the
receiver so if this this is a Omega
RF signal and if this is a Omega L
signal so uh ideally when when you
multiply these two signal you will get a
two term Omega RF minus Omega
L and Omega RF
plus Omega l
so up to now uh in entire all the
receiver architect architecture we have
added a low pass filter
here so what happens we have tried to
reject this uh frequency that is Omega
RF plus Omega L now when we are going
for the transmitter design we we are
going we are not going to use this
frequency uh our BAS band frequency is
less let's say 100 mahz and we want to
up convert into the 900 me at 2.4 GHz or
high
frequency so at that time uh so this is
a
receiver and in transmitter what
generally we'll do we will use a mixer
this is a base band signal so let's say
Omega base band and then Omega RF or
Omega carrier you can say and you have a
Omega RF plus Omega
base band and how we will do that we
will use a band pass filter
here
so so you will get Omega R
plus
Omega basement however transmitter has a
advantage of doing a multiple thing at
the base band and then you just uh do
the uh up conversion so this this is
called up conversion so in receiver we
use a down
conversion and in
transmitter we use a up
conversion so uh this is how the
transmitter will work so you can can use
all receiver architecture that we have
discussed uh in the uh last two three
lectures the same receiver architecture
can be employed in the transmitter the
only change is now we need to consider
the up conversion not the down
conversion and what is the another
difference that when uh we are receiving
the signal LNA is important
component but when we are doing the
transmission power amplifier because
that is a last component so this LNA is
a RF component and power amplifier is
also RF component so your low noise
amplifier here is important which is
connected to the antenna it should add a
low noise and have a higher gain however
power amplifier which is a part of
transmission meter it should provide a
sufficient power so that your signal can
travel to the long distance uh and
another important point is a it should
also H have a sufficient linearity we we
have seen in the basic of wireless
communication that when we are using a
complex modulation scheme like quam and
ofdm at that time
when when we are using this kind of
modulation we need our power amplifier
should be as linear as possible so that
while Recon converting the signal at the
receiver side we can easily reconstruct
the data which we have transmitted so
this is a basic difference in terms of
the architecture between the receiver
and transmitter now we will see one by
one all the transmitter
architecture and uh we will go through
uh the each components uh what are the
issues in the transmitter architecture
so same thing uh uh this is a very basic
transmitter architecture which has been
drawn here there is a baseband
data and then there is a address
generator uh which is generating the
address there is IR roome and Q roome so
in uh baseband you can easily do the uh
I data means I and Q data you can
generate then uh this I and q ro will
have all the information of the
modulation and everything your data is
there then you need a digital to analog
converter which will convert your
Digital Data to analog and then uh that
as a uh that data is a low pass filtered
and multiply with the cos Omega l t so
this is uh and then you will have a
modulated output signal after that you
can use a up conversion so means here
there is a COS Omega l t sin Omega l t
is applied so we are using a quadrature
modulation we are adding the signal and
then we need to use a power
amplifier so this is how the transmitter
architecture will work
so the basic transmitter architecture is
a high uh direct conversion transceiver
architecture where we directly convert
the uh baseband signal to the uh very
high uh frequency signal at Omega L2 so
if this is a COS Omega L2 and sin Omega
L2 if we multiply this is I data and Q
data it will it will be added so what we
will get I plus J q and we have seen in
the uh while discussing the Hilbert
transform if you do I + J Q you will get
the E to J Omega CT that is a carrier
the your signal is then of converted to
the carrier frequency positive carrier
frequency Omega c t and then there is a
power amplifier which will
amplify power amplifier has one
important component that is a matching
Network so your output of the power
amplifier should be match with the
antenna or this is a duplexer we have
seen the use of duplexer also if you
want to use a transmission and reception
both together we will use a
duplexer but there is a problem means
the same problem that we have discussed
in the direct conversion that that will
come in the uh direct conversion
receiver that will come in the direct
conversion transmitter also that is a IQ
mismatch and if uh IQ IQ mismatch uh it
follows that the power of unwanted
sideband uh divided by The Wanted
sideband is given by so what are The
Unwanted in when we have seen the image
rejection ratio also that same thing and
when we are uh discussing the IQ
mismatch also the change in the
amplitude so 1 + Sigma so Sigma is a
error in the amplitude and Delta Theta
is a error in the phase so if uh when
you are applying with cos Omega l t and
sin Omega l or t if there is a change in
the phase of Delta Theta or if there is
a change in amplitude of Sigma this is
what IQ mismatch you can
quantify by using this equation so if uh
you do not have the
uh uh Delta Theta is zero means there is
no phase difference then your IQ
mismatch is uh zero so there is a uh you
cannot find a sufficient uh IQ mismatch
but in reality there is a difference
between cos phase of cos Omega L and sin
Omega l t and it will add some IQ
mismatch there is another problem in the
RF frequency that is
carrier leakage same we have also
discussed in the direct conversion so
here what will happen that when you have
a COS Omega L2 T and sin Omega L2 T the
some of the portion if it is uh Power
amplifier and then that has a this
carrier because when we up convert the
signal some of the portion of carrier
will go and leakage
so that that will leakage to the
receiver and this leakage is very severe
when we are uh using uh direct
conversion architecture because your RF
frequency and ELO frequency both are
same and then you you also need to
consider the if mixer is also nonlinear
then it will add the uh sufficient
nonlinearity in your
entire uh receiver entire transmitter
architecture so the we we will discuss
about more in detail about the all the
transmitter architecture in the next
class uh thank you and uh all other
information about the transmitter
architecture will be uh we will discuss
in the next class thank you all of
[Music]
you
[Music]
