Mod 06 Lec 29

IIT Roorkee July 201
61 followers
2 Video Views·Dec 4, 2023
Lateral Stability, Construction and Sinking of Well Foundation
Prof. B. K. Maheshwari
Dept. of Earthquake Engg.
Indian Institute of Technology Roorkee
Roorkee -247667
[Music]
[Music]
new
nptel lecture on earthquake wrestling
design of foundations
this is 29th lecture on this prd of
foundations
and we are continuing with the fourth
module of the course
that is on the valve foundations so you
could see that
within the valve foundations we have
covered these topics
introduction which is already over
second part that is lateral stability of
well foundations
almost we have done with that and today
we are going to discuss the remaining
part of that
and then today we will also talk about
how to construction thinking of
a valve finally then in the next lecture
we will discuss the last two topics that
is tilting and shifting of wells and
some numerical problems
so let's start from lateral distribution
foundations
as discussed in the last lecture in 28
lectures
there are four different methods
for lateral stability of wealth tarjaki
we have discussed in detail
fender and banerjee and gongupada that
is also discussed and the last method
that is the fourth method is
by indian road congress called irc
method
which is from irc 45 1972
and formulated recommendation for well
in a cohesion-less soil
to estimate soil resistance below
maximum score level
and there are two methods of irc one is
elastic theory method
which we have discussed in the last
lecture today we are going to talk
ultimate solution method of irc method
so
let's start with ultimate solutions
method and you see in the ultimate
solutions
uh on the basis of elastic theory
the pressure on the sides and at the
base under design loads were determined
however to determine the actual factor
of safety and yes failure
calculation of ultimate soil resistance
is necessary
for checking the ultimate load capacity
of a valve foundation
the applied loads are increased by
multiplying them with suitable load
factors
and which is for various node
combinations and the ultimate resistance
is reduced by appropriate strength
factors
and two are compared so what is done
here the loads are multiplied by some
factor
while the resistance is reduced by
appropriate strength factors
so two things will be done so continuing
with that
so what these are the steps what are the
steps for the ultimate solutions method
the first
step the compute the applied nodes for
various combination flower factors
as given in this slide so there are
uh six different combinations has been
given here
first is 1.1 times d and then
second third fourth and like this
so you have here five combinations and
out of these five combinations what is d
here d is called dead load l is live
load including breaking effect
b is buoyancy wc water current force
ep is earth pressure force w is wind
force
ends as a seismic force here
as usual you know that out of wind force
or seismic force only one of them is
considered
ah we don't consider wind force and
seismic force together
as usual so out of these five
combinations
with load factors different load factors
for different types of load
whichever we give you the brush
combination that need to be considered
in the analysis
so the method assumes in this method
which is on ultimate solution method it
assumes the point of rotation
is at a height of 0.2 times the depth of
valve
above the base of that which we will
discuss later and the bending moment
should therefore be computed at the
point of rotation instead of the base
so first thing is that it assume that
point of rotation is not at the base
rather at a height of point two times
the depth of the one
so continue with that so step two is
here
the first chat needs to be applied in
the step two once you have calculated
the load
then maximum average pressure at the
base which is total load downward load
acting at the base of the valve
including the self weight of the vial
increased by suitable load factors
as discussed in step one once you know
the value of w
then it should be divided by the area of
the base of the valve
so you get the pressure at the base and
this pressure should not be
uh that q uh greater than q u by two
what is q u here
ultimate bearing capacity of the soil
below the valve base
so once you get the ultimate bearing
capacity of soil below
the base half of that that is the fact
of
safety two for ultimate bearing capacity
which will be your
sub variant capacity then
the pressure coming at the base should
not be more than that
so this is the first step suppose this
chat is not satisfied in that case the
diameter of the valve should be
increased
if the condition this condition is not
satisfied so this was step two
now in step three you calculate the
resisting moment of the base
which is denoted m subscript b at the
plane of rotation
and this resting moment is given by the
relation
q w b into 10 phi where b is the width
parallel to the
direction of forces in the case of
square
and rectangular wells or
diameter of circular wave so it will be
a width in case of in square case you
can have wait for length is same
but in rectangular case it will be width
parallel to the direction of forces
and or if you have circular valve then
we should be taken as the diameter of
the circular band
q is a constant which depends on the
shape of the valve
and the ratio of the depth to width b
so for a circular base a share factor of
0.6 shall be used
but for rectangular wells q depends on b
by b ratio
and this value of q lies between 0.41 to
0.64 depending on d by b suppose d by b
equal to 1
then it will be 0.45 if d by v is
increasing then the value of q is
increasing but the value of q will be
always less than one
that is need to be understood and phi is
the angle of internal friction
so using equation three one can
calculate
the value of resisting moment at the
base
continue with this in step four
what we calculate we calculate the two
moments
one is called on the surface and another
is at the
base so the compute the ultimate moment
of resistance in sides of the valve
and the moment of resistance is due to
fastest passive soil resistance ms
and frictional resistance mr what you
have
passive solar resistance ms is given by
the relation 4
where and for
frictional resistance is given by
equation 5 or 6
equation 5 will be applicable for
rectangular valves
while equation 6 will be applicable for
circular levels
in these equations gamma is unit weight
of soil
l which is coming here is positive width
of soil mass
offering resistance for circular wells
it will be 0.9 times the diameter
while d is grip length below maximum
score level
which is also called depth of valve
foundation i emphasize again here
that capital d in all these valve
foundations
is not the diameter of the valve rather
it is used at the depth of the valve
foundation
so capital d is will be depth of well
foundation
and that was the same thing in case of
tarjani's theory also
now what is kp and ka they are
basically active and passive coefficient
of earthquake to be calculated
using columns theory so k is active and
kp is
passive earthquake pressure coefficient
delta
is the angle of wall friction which is
taken as two third of phi
where phi is angle of internal friction
but the maximum value of delta should be
taken 22.5 degree
for example if you have phi equal to
30 degrees and two third of five will be
20 then it's fine
but if you have phi equal to let's say
36 degree
then it will be 24 degree two third but
we need to test
the maximum value upper limit is 22.5
degree
so the in equation 4 5 6 you calculate
ms and mr mb is already calculated
so we sum up all these moments
applied so the com applied ultimate
bending moment
m should be compared with the total
moment of resistance
what you have mv plus ms plus mf all
these combination will give the resting
moment
and this resting moment should be
multiplied by factor 0.7
which is kind of a strength factor and
so you got the
total value resistance moment mr
and this mr should be
uh should not be less than the applied
moment
or you can say that applied moment
should not be greater than mr
okay so we need to apply this check also
that the value of m1 should be
e less than uh should be should not be
less than
n okay and if this condition not satisfy
in that case the grip length of the well
needs to be increased
and computation is redone the equation
used in the plastic theory
so let's see that these equations which
are coming how they have been derived we
will discuss in briefly
first of all basic reaching moment mb is
the moment due to the frictional force
developed along the rupture surface at
the base
and b is the resisting moment of the
base and this rupture surface for square
walls is assumed to be cylindrical
passing through the corner of the wells
for circular wells the surface of the
rupture is assumed to be a part of a
sphere
with its center the point of rotation
and passing through the periphery of the
base
so it is explained in this figure so you
could see what is shown in this figure
you have a cylindrical valve the depth
of the valve
is d capital d and h is the height of
the score level
from the ground level small edge then
what you have the o
o is here set as a point of rotation
and r is the radius of this valve
cylindrical valve
and this point of rotation is at a
height nd where
n is normally point two as discussed
later also and this is the plan of the
valve
where width of the valve is b and length
of the wheel is l
so that means its cross section is a
reacting rectangular not the circular
and then what
you have here is shown is the forces
acting from
applied load which is per unit width
will be w divided by v
where v is the width of the well
foundation
and upward base pressure
for unit weight is also same so here w
is the total vertical load
taking into account the modification due
to load fractures
the load per unit width will be w by v
which will be equal to the upward
pressure
considering a small arc of length at an
angle alpha
from the vertical axis the vertical
component of force on element
is given by this relation rd alpha cos
alpha wb
okay and ultimate solar resistance
method
so what you have in the ultimate swivel
resistance method
uh this the forces we see the normal
force developed at the element
due to vertical force is given by this
relation
bf and w by b rd alpha cos alpha cos
alpha
in this case what you have uh you have
this
uh the value of this this is for
particular slide
okay and this should be because this is
a component
uh this uh force and uh the cos alpha
is its component now to calculate the
value of n it should be integrated from
zero to theta
once you do this integration then you
end up in this equation r w
d theta plus sine theta cos theta now
the value of sin theta and cos theta
are given from these relations and if
you
uh then you once you've got the sine
theta and cos theta from this figure v
by 2 r and d by r
then tan theta can be found from this
relation and
r will be simply the you can
sine square theta plus cosine square
theta will be 1 and then
r can be calculated and once we
substitute all these
bad in equation 9 a then you get
equation 9c all right continue with that
the moment has the moment of resistance
of the base about the point of relation
md is given by this relation where mb is
f1 tan phi into r okay
where irc 45 uh
method recommends a multiplication
factor of 0.6
to equation 10 to account for the
surface of rupture being a part of a
sphere
all right in both the cases i'm assuming
the point of rotation at point
2 times d as shown here the moment
transition the base can be expressed by
the equation 11
where it is 10 phi as it is fn
is uh like you know this f1 into
r is replaced by q into w so
ultimately the moment of resistance is
given from this relation
and this b is going through parallel
which we have already discussed
and for circular base mu should be 0.6
otherwise you need to be calculated from
the table
continue with that now ah continue this
derivation part side resistance ms how
to calculate the sine resistance
ms and then the friction force m
so for calculation first thing is here
that it is assume in this case that the
point of rotation o
is at a height point two times d here as
shown in this figure
now when we extend this od
so it cut at e and you have v1
v1 is this height let's say and d is the
total depth of valve foundation from
similarity of triangles
d1 will be one third of the total d
okay because this is uh this will be
our d1 will be one third of d that means
it will be
at the if we put this so it will be at
the centroid of this
now taking moment of force is about the
point of rotation o
moment per unit width is calculated from
this relation which is 0.096 is roughly
0.1
gamma d k p minus k this is for a unit
width
for a width of l the moment can be
calculated from this relation
and for uh when we to calculate the
value of
mf what is total friction force per unit
width is area of triangle aoe shown here
plus area of triangle body multiplier
sine delta
so all the numbers have been put it here
and finally
total frictional per unit width is
calculated
in uh equation this and
we get this for a rectangular value with
l
the moment about the center of rotation
is given by this relation
one point one by three gamma d k p minus
k s v by two so once you
uh uh simplified you get zero point one
eight three roughly zero point one eight
zero gamma
k p minus k lvd square sine while for
friction
for circular valve this equation get
hold 1 by 1.13
and gamma d so you have this for a
circular valve
where ah v will be the diameter of the
valve
and l is the projected way for us uh
for circular valve l is taken as 0.9 b
but for a rectangular valve this this
equation will be
given by from this relation which is
given in
0.11 gamma kp minus ks so this is coming
basically
once you you you do for circular once
you put this number here
so this was for a rectangular valve
and then you got when you put l equal to
0.9 b in this equation
then this equations become for the
circular one so this was for the
circular valve and this top one is for
rectangular
so this continues this now let's discuss
the construction and thinking of a valve
construction of well foundation consists
of the following
five stages first is laying the
cutting is second alignment control
third construction of well curve fourth
construction while staining
and finally well sinking so let's
discuss one by one
laying the cutting is well foundations
are constructed in stages by sinking
under self weight
as well as raising the soil inside the
raised hole and on the sides outside
the first step in the construction well
foundation is to lay the cutting edge
and welcome
if the riverbed is dry the cutting is
placed in position after removing the
top loose layer of
sand
the second stage which is alignment
control the center line of the valve
should coincide with the center line of
the abutments and tears end of the
breeze
pillars are constructed on the center
line of the breeze to serve as
registration points for checking the
alignment of the abutments and piers
third stage construction of velcro the
weld curve is assembled
on wooden blocks of sandbags plus at
suitable intervals
so that it doesn't sink while assembling
the curve
concreting is done after pressing the
reinforcement
m15 or which are great concretely used
for the
the weld curve is then allowed to set
for a week before sinking is started
the weld curve is allowed to sink alone
before raising the standing above
it so before you start the construction
of staining
the welcome should be finished now
fourth stage
which is the major stage there is the
construction of values training as we
discussed
that value standing is the measure or
body of the valve
and this is the the main body of the
valve
the grip length of the valve is very
small at the beginning of the sinking
operation
and the chances for tilting are more
therefore the
staining should not be raised to high in
the initial stress of well singles
which would otherwise lead to increasing
the tilting further
as the valve curve is first allowed to
sink alone and the staining is then
raised in small heights of
1.5 meter at a time allowing minimum 24
hours before adding the next height of
this training
so initially the first stage
uh once you have done with the valve
curve the next is the
uh raising the staining the initially
height
it should be at only in the in a small
height of 145 meter
and once you raise for 1.5 meter then at
least you should be allowed to
uh for 24 hours for that to get strength
before the
adding the next height of the system the
staining can be raised in installments
about three meter
once the well has sunk to a sufficient
depth you get a
minimum grip length of six meter so once
the your the
valve is sink to six meter then we can
increase the
standing in a uh increment of three
meter
before that increments should not be
more than one point five meter
the staining machinery should be
constructed perfectly vertical to ensure
vertical thinking of the wire
the stresses of the about two meter line
should be used for this purpose
along the outer periphery of the
standing at suitable intervals
when the straining is raised by this
height the straight edges are removed
and fixed at a higher level and the
entire height of the strain should be
raised
using this procedure
now the well sinking the soil in the
dress hole is excited
to facilitate sinking of the valve a
large size spread known as
jam is used for acceleration underwater
and this zhang consists of a sector
shaft steel pan
with edges connected by rope and wooden
ghoulies
when jam is used expression is done
manually hence well sinking slower
alternatively automatic graphs or razors
can be used for expression
operated by winch and the crayon many
times what is called bells razor is
commonly used for sandy soils
as the sinking proceeds more the depth
of the valve foundation will be below
the score level
increasing the frictional resistance
between the staining surface and the
surrounding soil
the staining is loaded with what is
called the net layers through a suitable
platform
and the sandbags piled on it to add well
sinking
overcoming this frictional resistance
the platform for the netherlands is
constructed in such a way
that it doesn't obstruct the grazing
process
air and water jets are also used in
addition to the networks to further
overcome the frictional resistance
and these are consists of gi pipes of
2.5 to 5 centimeter diameter with a
nozzle at one end
so this was the stage 5 where wells
which was related to well sinking so
in summary well sinking may stop and
tilting may also occur when the cutting
is encounters and over structure below
it
the obstruction can be removed by
dividing the vial using what is called
pulsometer
pumps and blowing the sand into it the
dewatering process should be
continuously washed and should be
suspended if there is a tendency for
tilting of the valve
dewatering also should not be used
unless the valve has sunk to a
sufficient length of minimum of nine
meters
okay so at least the valve is already
sunk to the nine meter then only
one should use the demand ah these are
the references
most of the material are taken from the
first reference
which is uh by a book by gopal ranjan
raw
bc and supplies applied soil mechanics
and he
is in india international okay
so this resource material is gratefully
acknowledged
and speaker is thankful to the authors
for such a nice excellent
literature so with that i conclude for
today's lecture
thank you very much
[Music]
you
[Music]
you
