Building the Catalina Wherry - Part 31 - Joggling frames

Nomad Boatbuilding
98 followers
Nov 12, 2023
My website: https://www.nomadboatbuilding.com
Instagram: https://www.instagram.com/nomadboatbuilding/
It's not about the money but living isn't free...
Here are some ways you can support this channel.
Get 5% off TotalBoat products here: https://www.totalboat.com/?sca_ref=3715732.xvvNNHFDPJ
Get 10% off Starbond Adhesives. Use the Coupon code NOMAD10
Shop here: https://starbond.com/discount/NOMAD10
Buy some merch: https://www.nomadboatbuilding.com/shop/
Support these videos with monthly or annual pledges at Patreon: https://www.patreon.com/nomadboatbuilding
Or make a one time donation: https://www.paypal.com/paypalme/nomadboatbuilding
all right my flipping hat where's my flipping hat gone no wonder i've been having trouble
concentrating my thoughts have been pouring out the top of my head so we got all of our frames
glued up here and it all looked pretty good although i notice on a lot of them i can see
this low viscosity epoxy is poured down and glued like probably like 75 of my clamps to the
to the stock so we'll see how that all works out but just start peeling some off here
go over these make sure all the pads are clean all right this polyethylene here look at this
it's right off that worked out quite nicely so i'm gonna peel all the clamps off of these guys
and then i gotta come up with an efficient way of cleaning this all down probably maybe
belt sander fluff trim router yeah it's a bit fussy for that i realized pretty recently that
half of my clamps live on the other side of the shop away from my primary gluing area so i think
one of the things i want to do actually is reorganize all my drawers and move a lot of
clamps right back here which is going to mean i'm not going to find anything for about six
months to a year anyhow this is the kind of thing that i too often do like at night off the clock
which is good for the customer bad for my bottom line there's you know there's you'd be surprised
how much time you spend just unclamping things you know you think about clamping stuff up taking
time unclamping well it seems fast you still got to put all these clamps away and sometimes clean
up clamps and things like that it all adds up so i'm going to stop rolling camera on this because
it's boring and uh we'll come back after a bit when i figure it out how i'm going to clean these
up okay sound good let's do that okay so cleaning these up so i'm using this little jig here a bit
of blocking to try and raise it up a bunch of above all the pokey stuff and to get it up above
this little wedge here just quickly hit it with some sandpaper to knock off the worst of that glue
and then i'm starting by just leveling it out with a plane to begin with i'm just knocking
this down until i'm coming close to the surface not worrying about hitting it and then i got the
belt sander here get it with that real quick and that's it flip it over do the other side it's
going pretty fast the most awkward thing is that i don't have good geometry here for working the
plane here we go there's another one done worry about cleaning up this bit of squeeze out on the
face later on otherwise that's ready to get fitted uh so i got all of our frames were made up here
and they're ready to get fitted into the boat now they're not going to fit like a glove they
have every one of these needs bevels to be applied to them um i was really hoping that i could get
them sort of square to the planking and not have to do a lot of beveling but it just doesn't feel
like it's going to go that way for me so what i'm going to do is they're all going to be square to
the shear because at the shear we have the in whale resting against it and not too far below
that we'll be having the rubber rail or the the thwart riser against it so i'm just trying to
keep it squarish to that if i can anytime you've got sort of a tricky tricky fitting situation it's
a great idea if you've got a couple sort of mock-ups that you can try that out on first
now these uh my first couple frames are just basically out of a straight piece of stock so
it's easy to mock that up farther back where they're sort of out of goonie shapes not so easy
so uh if i were to if i were concerned about it i would probably get like a one by six or
something like that and just try and cut a single piece out of here i didn't do that but um i'd hate
to screw up one of these laminated ones and have to go back and start laminating a new one that
would be a real real pain i did these in two separate pieces from the start and that's only
because if i had if i had some two by stock on hand i would have done these up as a single blank
laminated my backs onto them and then split these on the band saw or the table saw and then
dress them out separately but i just didn't have the stock all i had was a one inch stock on hand
so i decided to make them all up individually a little bit of a hassle but not huge and now it's
done so it's not really a big deal i probably saved on the time it would take to split these
in half which is not necessarily inconsiderable um so the one thing that i've got the you know
the laps are not right on the edges of the planks they're all up about a quarter of an inch
and the one side is not going to match the other side exactly and i'm going to try and match the
location side to side as close as i can and i'm going to try and square them all up to the sheer
plank and the rest is going to sort of land wherever it lands uh so the sheer mark is the
only thing that i've carried across from one to the next right here and back down here i've got a
little this sort of shortcut here um the reason for that is i knew i was going to laminate here
i didn't this is this is a cutaway for the where it meets the bottom of the boat and i just wanted
to make sure that i had something to clamp onto when i laminate the these guys at the ends so i
think what i'm going to do is go through this i think i'm going to just fit them all and then
i'm going to deal with this limber hole last okay let's take a look at what it's going to take to
fit a frame here so first off i just want to sort of look at the frame on the other side and make a
little bit of a notation as to how it fits i've got marks here at the sheer line where my station
lines are i indicated all of those marks earlier in the process where i punched along a line here
with two marks close together with an awl and that's just to make it easy to find because
there's little tiny nail holes all over the place i need to be able to identify the ones that actually
represent my station lines and so that's just a sort of a standard that i use they're about a
quarter of an inch apart and i put them within three quarters of an inch of the sheer so here
we go we've got our two marks right here on this particular mark i've drawn a line on here and
down at the bottom i've noted where my frame hits the floor on the other side and i'm going to try
and match it on this side so if we take our made up frame here i'm going to drop it in place
and right off the bat there's decisions that i need to make about how i'm going to fit it
it actually doesn't fit all that well it's quite a ways off of the mark and so what i'm going to
start by doing is splitting the difference which is what i did on the other side in terms of how it
fits i'm going to isolate the frame in terms of its position and attitude and then we're going to
scribe it to fit this position so there's different ways i can do that i could use a piece of blocking
like this to isolate it in place that's how i did my initial spiling in the first place and if i
line this up here on my marks i can tweak this guy until it lands exactly where i want it to
now the problem with this is that i can't have access to the back of here in order to scribe
along this last little portion of frame and i've got my cross ball in the way on the other side and
i don't want to move that so i'm gonna have to come up with a different way the next way i can
do it is i can just try and clamp it in position and i'm just going to use some shims to sort of
block it up at one end so that i can put a clamp on it and hold it hold it in position so i'm just
using a stack of stir sticks here to decide how far i want to block that out so i think i'm going
to go with like four stir sticks yeah maybe we'll go three so i want to try and find the happy
medium between how it fits at one end and how it fits at the other end i'm going to lift this up
just a little bit till it matches the sheer mark now this first scribing is not going to get me
super close but it's going to get me in the neighborhood so i just want to raise it up so
i'm a little bit above my shoe marks up here got the attitude right and because of the amount it
needs to be scribed back i've basically got one spot where it's hitting hard which is the other
side of the frame at this position i'm going to use dividers and i'm going to scribe the whole
thing like i would if i were doing log cabin scribing you know so we're just going to open
up the dividers to the widest gap and i need to decide on what my attitude is going to be i think
i'm just going to go square try and keep the dividers square to the face of the planking at
the midship's point that's the hardest part it's just going to be trying to keep this keep these
dividers the same in the same attitude open it up down there a little bit okay so right about there
so i'm just going to take those dividers across trying to be careful i'm not rotating the
the dividers as i do this keeping them in the exact same attitude that's how i started looks
pretty good and i'll do the same on the other side now okay there we go it's a fair bit of
joggling i need to fix in order to get this to fit right so we're going to move over to the
bench here put it in the vice and start whittling this down tell you yellow cedar the grain is
almost invisible on the stuff the first thing i want to do is just deepen my joggles a little bit
because they're all going to go down a little ways more so i'll just start by
doing this by eye just taking them down to about the depth of the next joggle that i need to
accommodate this one's quite deep
in general i'm gunning for removing as little as possible up here in this area because this is the
part where there's two major parts that are going to attach down here it doesn't really matter nearly
as much okay with sharp tools we're going to start working this down so i've got basically two lines
and what i like to do is i like to start on one side of course we're checking our grain
orientation which can be a little hard to see i'm working my way down to my line down at the edge
where i've got a line in the center i don't have a line so leaving it crowned in the center so on
this side i'm doing the same thing i'm just i've got my line there and i'm just i'm leaving the
hair the line behind i'm not trying to make the line go away and just work my way down to it
so with both sides whittled down to the line i can just remove the crown in the middle
and i'll leave this last one alone i've only got a whisker of a pencil line here i'm not sure if
it was from when i marked it the first time so i've got just a little bit of left uh a little
bit of uneven surface left i'm just going to use a sanding stick here to just try and knock that
just try and knock that down a hair okay that looks reasonable i know it's not quite a hundred
percent but that's okay enough to get us moving i'm just going to whittle this down until i've
hit each of these steps and given it a reasonable flattening out and then we're going to offer it
up back in the boat and see how close we are now i know i'm not going to be a hundred percent but
this hopefully gets me to within like 90 percent and the reason it's not a hundred percent is
because it's almost impossible to keep your dividers maintaining the exact same attitude
through that whole scribing process you can try you can screw around with levels on it but i
guarantee you won't be able to keep your eyes on the level and keep your eyes on the work at the
same time i'm not worried about trying to remove all my tool marks just trying to get that line
close and the closer i am hopefully the closer will be when we offer it back up obviously
okay there we go that is it for that sort of basic shaping now we'll throw it back in the
boat and we'll have a look at how we did well that's a whole lot better so it's important to
get it in the exact same spot because it does make a difference okay so now what i want to do is just
decide on exactly where i want to put my emphasis be it on pushing down the toe and working
working it until i can get this guy fitted back here or doing the opposite i can
push back here and see how much you need to work to get the toe down so or splitting the
difference so usually i start by splitting the difference rock it back and forth and try and see
where am i having the greatest amount of hang up there's always a fulcrum somewhere and it might
be buried underneath all the edges you know because my edges aren't dead flat necessarily
and right off the bat it's this one in the middle here that looks like it's the biggest culprit
so i'll just start there i'll start by flattening this one out and probably the sort of heel of this
lap here i'm just going to go back to the vice and tweak those then i'll be right back
drop this back into place now okay now i've really not taken much off of those
one thing i'm going to do is just going to add myself a sir mark on the inside here just so
that i don't have to keep staring over the back side of this to figure out if i'm in the right
location so it's a mark there and a mark there we'll do one in the middle too okay now your
attitude up and down also has an effect on this so let's make sure we sort of pick a spot and
do our best to sort of keep working from that so i'll give myself a couple sir marks there as well
so even the the little bit i took off already has had a pretty significant difference so i'm just
going to keep going over this like that hitting it in a few spots look for the high spots take those
down try it again see i'm not taking very much off i'm just doing a small amount like that and
then i test it again each of these testings is bringing me a tiny little bit closer the thing
i wanted to point out is at this point i can make some choices about how to fit this and what i find
is this rocking technique is often the best way to do it so if i were to push this down at the heel
get that fitting really good then i have to look at if i rock it up here where's the the what's
going to be the fulcrum of getting this to fit nicely because it fits pretty good up here if i
sandwich this up tight up here it fits okay but now it's bouncing up bouncing loose down there so
where is the what what's the the one spot that's holding it up and it's right here in the center
so i'm going to concentrate my efforts there to try and bring that down a little further
okay so if i look at this this one needs mostly this area back here addressed this one needs the
whole length addressed this one needs the whole length addressed this one needs just a little bit
in the middle but i know it's going to come down a bit so i'm going to do the front end bit
back here i got gaps i'm going to leave those alone at the bow there at the down at the toe
i got gaps i'll leave those alone and i'm going to check the other side for similar things
so i've just given myself marks indicating where i need to hit this do that both sides and if i
leave any marks behind i'll erase them and then start again when we do the next fitting okay so
how much i take off to do that just take off that much that's all i'm not going to go back and check
it again that got us a whole lot tighter just that little bit now if i rock it it's showing this up
here that it is is the the bounce point back of this joint up here try that again and it's feeling
like there's a whole lot less rock already just doing those little bits so it's kind of a game of
chasing your tail back and forth like that until you finally get to the fit that
you want of course i can just fill this all in with epoxy right now but i like to get myself
a little bit closer before i decide to call it quits okay i've gotten this down to my final
fit you can keep going and keep going of course but for our construction this is perfectly
acceptable it springs into place well enough it's still got a little bit of a rock to it
but not enough that it's really a big deal and i'd rather just sort of move on to the rest and
not worry about it too much so from here on in this is uh we'll just leave this alone and move
on to the next one of course we still have to think about cutting a little limber hole down
in the corner there and i'll probably pre-drill a few holes for our fastenings through the plank
from the inside here and that's just going to allow me to make sure that my aim is correct
for my fastening later on okay so i've got a few more left to do and they all pretty much
go exactly the same this one is a little trickier having an s curve to it i had a hard time getting
my fit correct on the other side and in fact strangely enough it fits better on this side
than it does on the side that it was uh patterned from so on the other side i think it took me about
two hours to get about five of these frames fitted like that so i've got uh what one two
three more to do and i still have to cut all the scupper holes or the limber holes down here at
the heel of the frames so we'll do that and then we'll do a bit of a round over on the edges i
think before we install it all right one of the things i'm using to help me with alignment is
this little angle block i've got clamped onto the gunnels here and so this is just controlling my
the attitude of my frame and so as i drop it into place it nests right up against that block and
that not only helps to secure it in the orientation that i want this way but it also controls the
its attitude this way because i want it just square to the shear plank here and so by having
that there just ensures that every time i go to fit one of these i've got something that really
registers it positively and i can very easily sort of gently pinch over here and play around with the
fit you know i can do my like rocking trick trying to find my little high spots every little bit of
movement in one direction or another or a change in attitude this way or that way will change up
how this thing fits quite dramatically and so this is a really important little tool
once i've got it fitting the way i like and as i said i'm shooting for something like within about
a 30 second of an inch of a nice fit i mean a nice dead tight fit is great but i'm not getting too
concerned about that i'm just going to draw where this frame lies right up against the planking
this is going to be helping me make sure that i do a proper wet out on the planking before when i
do the glue up and when that frame clamped in place i'm just going to mark it for a couple of
for a couple of things one thing i'm going to do is i'm just going to mark it down here on this
particular frame i need to cut it off so i'm going to mark where the cut off is another thing i'm
going to do is i'm going to put a finishing nail in right up here where it hangs over the shear line
and that's just going to make sure when i go to glue this in it'll drop right into place
so i can do my final shaping and round over and all of that sort of stuff and i still need to
drill for my fastenings and all these other frames i still need to do my limber holes so
i'm going to be doing that next and i'll be doing a little round over on this very tip as well
yep damn it i screwed this up
feel pretty stupid so i think i need to fix this
