Diesel Engine Oil Pressure Problems? Here's Why

Charley’s Garage
79 followers
Become a channel member and get lots of special perks and check out the merch store!
https://charleysgarage.myshopify.com/
A Basic overview of what diesel engine oil pumps do, what can happen when they get old and wore out, how to test them to see if they are worn out, and what some of the other reasons for a loss of oil pressure might be.
#diesel #training #mechanic #tech #automobile #basics #hydraulics #cummins #egr #emissions #international #DT466 #Maxforce
AI Generated·May contain errors
Hello, welcome to Charlie's Garage. Today's video is going to be about oil pumps. So,
what we're looking at right here is an oil pump that came off of a DT-466 International,
and I can take you over here and show you an example of what it looks like when it's installed
on the engine. So, right here on this MaxForce, it's the same water pump basically, but you've
got a hub right here that the vibration dampener attaches to, and then behind this hub, which
you have to use a puller to get off, and it's interference fit, so you actually have to
heat this hub up to get it to expand to fit back on. But behind the hub, this is the oil
pump housing, so that gear set that I just showed you over here is actually what it looks
like on the inside of it, right? So, the reason why we're talking about oil pumps is, of course,
oil pumps are designed to create the flow of the lubricating oil that travels through the
engine and helps lubricate and also, in some cases, cool certain components. And one of the
main things that you will have as an engine ages is a gradual loss of oil pressure that can be
attributed to primarily wear in one of two areas, and that would be your bearing oil clearance, so
where your crankshaft journals and your bearings meet, the space between the journals and the
bearings provides a restriction that creates oil pressure. Well, what can happen is that
the pump can also be one of the reasons for a loss of oil pressure, because like all pumps,
they will start to wear internally, and as the clearances get bigger inside of the pump housing,
you'll start to leak between places that you shouldn't. So, for example, when this one is
installed, it should be up against the block, and you shouldn't have too much leakage across
this face. So, one of the tests that we have the students here do is they'll take a straight edge
like this one, they'll put it over here, and they'll measure the clearance that we have between
the body and between the gear set, and if that clearance is below spec, then you know that might
be one of the reasons why you have low oil pressure or why the oil pump might need to be
replaced. Another test that we can do is if you look at this guy and we take this gear out,
do it with one hand again, there we go, we take that gear out, now it makes it easier to pull
this gear up, and you can see that this gear slides into this housing right here. So, what
we also measure is the space between the housing and this inner or outer gear right here, because
if that was excessive, that would cause a leak and cause a loss of oil pressure as well.
And then there's another test that I don't know if International actually lists this test in the
service manual. I know Cummins does, and they call it tip clearance. And tip clearance would be like,
this is your actual pumping chambers, and you can see that as this rotates around that the oil
clearance changes, right? So, it forms a big space that straws the oil in, and then as it
rotates, that space decreases and forces the oil out the outlet. And what'll happen is as you're
rotating this gear set, the space right here between the gears that separates the pumping
chambers from each other will start to leak by. So, tip clearance would be measuring the space
between these. And like I said, that this would all be reasons why you would need to replace that
oil pump. So, in addition to a long-term loss of oil pressure, bearing clearances, and then we'll
talk about those in a future video, maybe talk about how to use plastic gauge and how to measure
journals and bearings and find out what the clearance is. But this would be the other reason
for a long-term oil pressure loss right here would be the pump getting worn out. Some of
the questions I get a lot is what about the sudden oil pressure? Because usually wear happens slowly,
so this would be a long-term effect. If you have a sudden situation where your oil pressure gauge
is just doing this, right, fluctuating, then you probably have a high oil level that may be
getting aerated by the crankshaft. So, now the air is being sent through the lubrication system,
and since air is compressible, it makes the pressure really erratic. The other thing you
might have is where the gauge is reading high and then all of a sudden, boom, down to nothing and then
back up again suddenly, and that could be from a low oil level. So, sudden changes in oil pressure
are often related to issues with oil level. There could be another couple of few reasons out there,
but that's one of the main ones, whereas a sudden gradual loss is going to be a pump or the bearings.
So, I hope this helped explain some of the things that oil pumps do, what they can go bad, how we
can measure and test them to see. If you have any questions, please put them in the comments.
Please like and subscribe, and please share this video with other people that you think would be
interested in learning about diesel components. Thank you.
