Welcome back to Nomad Boatbuilding. I'm Mark Rutten and this is a bonus episode of my building the Tahit Kayak series.
This is a video diary to the client who
requested that I build the model Tahit Kayak that we've used in the rest of this series. Now just by coincidence
the last full-size Tahit Kayak that I attempted is back in the shop getting re-skinned. The customer wanted to make some changes and
so we have an opportunity to look at how we built that framework, how we've modified it,
because this is not its first re-skinning job and
perhaps you can pick up a few tips that will help you to build your version of the Tahit Kayak.
Now just a caveat, this boat is now going on to its third re-skinning as the client wanted to make more changes and
with each skinning the boat's gotten re-dyed and so this framework is looking pretty crusty. Now it's perfectly sound
but you'll notice all kinds of little changes have been made along the way at the request of the customer.
I just want you to know that normally these boats look a whole lot prettier when they're first done. Let's get right into it.
Okay, Patrick as luck should have it the
the Tahit Greenland Kayak has come back into my shop just while I was working on your model.
The client wants to re-skin it and make some changes so
you get to have a closer look at some of the details here.
Now,
so one thing I want to point out is that
this boat was not
specifically built to be as close to a replica as a Tahit as you could possibly make it.
But it's it's sort of starting out with the Tahit
sheer profile
but ultimately it's got to fit the paddler so
changes are made to accommodate that. So I just thought I'd show you a few things. I build things differently almost every time and
I don't like to prescribe exactly how
one should build stuff. So
this frame shows, you know, one approach.
The drawings I gave you is going to show a slightly different approach.
The model I'm going to send you is going to show you yet another approach.
So I think it's the greater value is in
trying to find the things that make that seem like the right way to go for yourself.
So one example is is the way I do decks here. This is sort of my standard deck configuration.
It's
normally about 12 inches long and
the idea is that the deck is
the thing that allows the transition from the gunnels here, of course, to the stem.
And the stem is always 3 quarters of an inch wide so
there's always a point at which it comes down to 3 quarters of an inch and then flares out.
But if you look at the Tahit lines, the Tahit lines are quite full all the way through here right to the end.
They don't have a hollow in here. And so if you want to mimic the Tahit deck line,
you're going to
you're going to think about that. You're going to make sure you're planning out your gunnel construction and
stem construction so that this all comes through and you bridge that gap.
And this might end up being almost like an overhanging T-section all the way through instead of coming into a pinch here.
And so this deck might just go right to the end of your stem.
Also, this is quite narrow
because that's the way I like to do it, because the way I like to close up the ends.
But if you look at a Tahit, it's probably closer to like
2 inches or something like that.
An inch and a half at least.
Deep there.
This boat was made much
with much a narrower chine
originally and then the customer wanted me to deepen the chines to give it a
harder turn of the bilge. So these have got like kind of stupidly, overly deep chines.
I would never do those normally that deep. Usually they're
3 quarters of an inch to an inch at the max.
And your model will be reflecting that. And then the
the massacre construction.
Here we're going with a very simple sawn massacre that's laid right on top of the gunnels.
And I think we had a different one the first time around. In fact, we had, yeah,
we had a much higher one that I think we had laminated, but that didn't suit the
woman who was paddling it in the end. And so this was a different
solution we decided to come up with. And then now she wants a secondary
deck beam farther forward that can catch her thighs and make for a tighter fit. So that's why we're doing that.
However, your model has got a style of
massacre knee brace that I would, that I bought and put into my regular boats.
And these would be like a typical sawn one or something similar to that.
Like I say, I do them a little different all the time. And then of course there's
a hatch going in here, which is why this hatch frame has been included. I don't like hatches,
but they have their uses. And this is a kayak sport hatch, which is quite a chunky
affair.
So there's the, there's the lip. You can see how we've got the lacing holes. You skin the boat,
you lace it on with this, with the seam still intact, or rather, I'll skin the whole, I'll sew the whole thing on.
I'll, I'll leave the seam in here a little slightly undone, but still stitched together. And then you stitch it down to the frame.
You do all your gooping and then you come back later on after everything's cured and then you trim out the hole.
Drop this guy on there.
Attach that with Sikaflex, and I've added just four small screws to keep it tacked in place. And then
the lid. So this thing's, like, sits quite high.
It's like a solid inch high, which is what I don't like about it. I prefer one that's something that's more flush.
I remember I was mentioning about the dropped
backrest.
So this guy originally was higher than we did, dropped it down to about, it's about an inch below the
edge of the gunwale. That's to allow layback roll.
So when you're looking at the boat when it's skinned,
you don't notice that this is dropped because the cockpit hoop just floats above it.
That's not until you lean down onto it that it drops down.
Also, the whole, the hoop sits quite a ways back. And so that's just to minimize as much
interference in the layback. So it's set quite far back from this, this position here, too.
Now, this thing looks rough because, of course, this is its third skin now. And,
and frankly, you know, skin boats
look fine when they're freshly built. But once they've had a skin on them for a while, they look pretty,
pretty rude once you peel that skin off. My typical gunwale construction here. I usually go about an inch deep and
roughly six inches long. This looks like it might be a little bit longer. Might have gone about eight inches.
So you might want to play on paper
what the best angle is for this.
Because, of course, the grain orientation of the stem itself can be affected by that.
And we're, I mean, we want to try and get this out of as narrow a place of material as possible.
So I think I was probably worked with something that was like four inches wide or something. And so the general
direction of the grain usually matches this angle for efficiency in getting the part out.
But, of course, you've got to make it from there all the way down to some sort of transition in here.
So that's the the trick of designing a stem is to try and work out
what's this geometry going to be and does it allow for a stem that's going to extend
far enough back for your tastes.
So again, that's something you could do on paper. Or look at the example I drew. Maybe that works out for you.
And you don't want to pre-make your stem
shape entirely necessarily. Like when I do these, I usually leave this
like full. And then when I'm building the boat, I'll lay the keel alongside of it to find the right
position that I want it to figure out the depth here. And then I'll mark the keel and cut it.
And I'll usually leave the keel stem and cut it. And then I'll usually leave this a bit rough too.
So I'm only worrying about this material in here. This joint here being the thing that I'll fit. And the rest I'll leave
just chunky until I've established
how the keel interacts with it.
Once I've done that, then I'll design what all the little swoopy-doos are going to look like.
And so I'll just attach this guy on with like some zip ties or hot glue or something like that to
tack it in place.
Same thing back here. I actually like the way this... I like the shape back here better. It's kind of a flatter
shape. And it kind of swoops up a bit too much for my taste up at the bow. But I think if we look at the...
Yeah, if you look at the drawings, the way the original Fahy is... Yeah, it's got quite a...
It's got quite a sweep at the bow as well. And then it's turned much flatter.
So I guess it's a reasonable representation.
You'll notice on the drawing how this kind of goes gonk, gonk, kind of a hard turn here. Well, that's... I mean, that's the
the deck beams will spring down to create the shape. And
this is... what you're seeing here is more like a cross-section where the deck beam lands right on this...
where the deck stringer lands on this deck beam.
But the shear itself runs through and it'll... the shape will all fair out. It shouldn't... there isn't like a hard turn here.
It should be a nice, fair, smooth curve.
So here in my drawings, like, this is how I would normally build a stem looking at it from above.
And from the side, as you can see in the example,
the built example, that's what it looks like.
But this is more what if you were to do something that matches the lines, you'd need to do a pole-sized deck.
I didn't draw a profile view of that. The drawings...
I'm sorry, the drawings are not a hundred percent
perfect.
As in some of those details don't entirely jive.
But you need to... it's important that you don't just follow my stuff
by rote. It's important that you try and figure it out for yourself and think. Think about how
you're trying to create these shapes. That's what I think the most important thing is here. Look at the shape and
think about how you need to build it in order to
recreate that shape because that's your goal.
You don't get... this isn't paint by numbers anymore like Brian's plans are. Time to put on big boy pants.
Now if you're interested in building your own skin-on-frame version of the Tahiti kayak, I have a set of drawings available on my website.
They're not prescriptive plans. There are a bunch of documents I produced as I went through this process myself.
Includes lines drawings, framework drawing, a bunch of details, and a few full-size mold drawings.
You can find links to those down in the description. By buying these drawings you're helping to support these videos, and I thank you very much.